Austin Hughes Electronics Cyberview NCP-1716 User manual

User Manual
NCP-1716
16-port Console Terminal LCD Keyboard Drawer
-1U 17" screen size
- Designed for SUN, all headless
servers

Chapter 1 Getting Started
1.1 Important Safeguards..........................................................1
1.2 Regulatory Notice................................................................2
1.3 Package Contents...............................................................3
1.4 BeforeInstallation................................................................4
1.5 Unpacking...........................................................................4
1.6 OptionalAccessories...........................................................4
1.7 Structure Diagram...............................................................5
1.8 Installation...........................................................................6
1.9 How to Use "N" Series LCD Keyboard Drawer...................7
1.10 How to Use the Slides .......................................................8
1.11 How to Use "One Man" Installation Slides ....................9-10
Chapter 2 How to Connect Console Terminal LCD
Keyboard Drawer
2.1 Connection Diagram..........................................................11
2.2 Membrane.........................................................................12
2.3 Configuring the Local Console....................................13-15
2.4 Changing Operating Parameters.................................16-23
2.5 Local Keyboard Commands in Native Mode....................24
2.6 Connector Pin Assignment................................................25
2.7 Command Guide...............................................................26
2.8 Device Setup...............................................................27-28
Chapter 3 IP Setting
3.1 IPConfiguration.................................................................29
3.2 IP Filtering...................................................................30-31
3.3 Web Server Configuration...........................................31-33
Chapter 4 Serial Port Configuration
4.1 Serial Port Configuration.............................................34-39
4.2 Connection.........................................................................40
4.3 Serial-to-Serial Function...................................................41
Contents

Chapter 5 System Status & Log .............................................42
Chapter 6 System Setting
6.1 System Administration.................................................43-44
6.2 Date and Time..................................................................45
6.3 Fireware Upgrade........................................................46-47
Chapter 7 Operation
7.1 On-screen Display Operation............................................48
7.2 On-screen Menu...............................................................49
Chapter 8 Standard Specification
8.1 Specifications.....................................................................50
8.2 Keyboard...........................................................................51
Chapter 9 Optional Specification
9.1 DC Power Options............................................................51
Chapter 10 FAQ....................................................................................52-53
Chapter 11 Dimensions......................................................................54
Contents

1.1 Important Safeguards Chapter 1
P. 1
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
■Any product, on which the serial number has been defaced, modified or removed.
■Damage, deterioration or malfunction resulting from:
□Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modifi-
cation, or failure to follow instructions supplied with the product.
□Repair or attempted repair by anyone not authorized by us.
□Any damage of the product due to shipment.
□Removal or installation of the product.
□Causes external to the product, such as electric power fluctuation or failure.
□Use of supplies or parts not meeting our specifications.
□Normal wear and tear.
□Any other causes which does not relate to a product defect.
■Removal, installation, and set-up service charges.

P. 2
1.2 Regulatory Notice Chapter 1
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the
correctness of the contents. The information in this document is subject to change without notice. We are not
liable for any injury or loss that results from the use of this equipment.
Safety Instructions
■Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned enviro-
nment with temperatures not exceeding 40º Celsius (104º Fahrenheit).
■When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and
causing damage to other equipment or injury to persons nearby.
■When the drawer is in an open position, do not cover, block or in any way obstruct the gap between it and
the power supply. Proper air convection is necessary to keep it from overheating.
■Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage
and current labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be
higher than the one listed on the equipment’s ratings label.
■Observe all precautions and warnings attached to the equipment.
■If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent
being damaged by transient over-voltage.
■Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to
the power supply or on other hardware may cause damage, fire or electrical shock.
■Only qualified service personnel should open the chassis. Opening it yourself could damage the equip-
ment and invalidate its warranty.
■If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service
personnel.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equip-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
■Re-position or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

P. 3
1.3 Package Contents Chapter 1
Console terminal LCD keyboard drawer x 1 pc
RJ45-DB9 female adapter x 1 pc
RJ45-DB9 male adapter x 1 pc
Fasteners for rear L-bracket x 4 pcs
330mm rear mounting L-bracket x 1 pair
* NCP-1716 mounting depth-adjustable from 320 to 920mm
User manual x 1 pc
CD disc x 1 pc
Power cord x 1 pc
5
4
2
1
3
1
23
User
Manual
45
6
6
7
7
6
8
8

P. 4
1.6 Optional Accessories
■It is very important to locate the console terminal LCD keyboard drawer in a suitable environment.
■The surface for placing and fixing the Console Terminal Drawer should be stable and level or mounted into a suitable
cabinet.
■Make sure the place has good ventilation, is out of direct sunlight, away from sources of excessive dust, dirt, heat,
water, moisture and vibration.
■Position the console terminal LCD keyboard drawer with respect to related facilities.
The console terminal LCD keyboard drawer comes with the standard parts shown on the package contents. Check and
make sure they are included and in good condition. If anything is missing, or damage, contact the supplier immediately.
1.5 Unpacking
1.4 Before Installation Chapter 1
1. RJ45-DB9 adapter
1.1 SG-100F RJ45-DB9 female adapter
1.2 SG-100M RJ45-DB9 male adapter
2. Cat5 Cable
2.1 CU-3 3 feet Cat5 cable
2.2 CU-6 6 feet Cat5 cable
2.3 CU-10 10 feet Cat5 cable
2.4 CU-15 15 feet Cat5 cable
2.5 CU-33 33 feet Cat5 cable
2.6 CU-66 66 feet Cat5 cable
3. " One Man" installation slides
3.1 NBK-01 Single or "One Man " installation slides
* Please refer to P.9 - 10 for Installation guidelines
4. Power Cord
4.1 IEC power cord
4.2 NEMA 5-15 power cord (US)
4.3 BS 1363 power cord (UK)
4.4 CEE 7/4 power cord (German)
4.5 AS 3112 power cord (Australia)

P. 5
1.7 Structure Diagram Chapter 1
Adjustable rear mounting L-bracket
Micro switch for screen auto power off
Serial port status LED
Keyboard interchangeable module kit
Carry handle to release the 2-pt lock
2-point lock
LCD interchangeable module kit
LCD membrane
1
3
2
4
3
5
6
6
7
7
8
8
1
2
4
5

P. 6
1.8 Installation Chapter 1
■Install each rear L-bracket using two fasteners shown
in Figure 1.
■Leaving the fasteners slightly loose.
■Measure the front and rear mounting depth of the
rack.
■Align each rear L-bracket to a suitable length and
tighten the fasteners shown in Figure 2.
■Fix the the LCD keyboard drawer into the rack.
* Hardware (screws and cage nuts) for fixing the
mounting bracket to the rack is not provided.
Figure 2. Aligning the rear L-brackets to a suitable length for the rack.
Figure 1. Installing the rear L-bracket to the LCD keyboard drawer.
Figure 3. Fixing the LCD keyboard drawer into the rack.

P. 7
Chapter 1
1.9 How to Use "N" Series LCD Keyboard Drawer
■Gently pull the tab toward the front of the LCD shown
in Figure 4.
Figure 4. Pulling the tab toward the front of LCD.
■Operate the LCD keyboard drawer shown in Figure 6.
Figure 5. Flipping up the LCD to a suitable angle.
■Flip up the LCD to a suitable angle shown in Figure 5.

P. 8
1.10 How to Use the Slides Chapter 1
■Hold down the white arrow button until the LCD key-
board drawer is located in the rack (shown in Figure 9).
Figure 9. Pushing the LCD keyboard drawer into the rack.
Figure 8. Pushing the white arrow button.
■Push the white arrow button on either side of the LCD
keyboard drawer to unlock (shown in Figure 8). Avoid
pressing the red button located on either side.
■A white arrow release button is located on the outside
of each slide (shown in Figure 7).
Figure 7. White arrow button.

P. 9
1.11 How to Install "One Man" Installation Slides Chapter 1
4
5
6
7
Package Contents
Install the front mounting ear x 2 pcs
1
2
■Disassemble the standard front mounting ears carefully.
■Install the optional front mounting ears with M3.2*4.5mm screw x 8 pcs.
4
5
6
7
Mounting bracket x 2 pcs
Front mounting ear (left &
right) x 2 pcs
Support bracket x 4 pcs
M6 cage nut x 8 pcs
M6 washer x 8 pcs
M6*15mm screw x 8 pcs
M3.2*4.5mm screw x 14 pcs
5
4
2
6
1
3
7
1
2
3
4
5
6
7
Model No : NBK-01

P. 1 0
1.11 How to Install "One Man" Installation Slides Chapter 1
Install into Rack
1
2
3
■Attach mounting brackets to vertical mounting rails.
■Leaving the screws slightly loose.
■Attach support brackets to chassis with M3.2*4.5mm
screw x 6 pcs
■Pickup the unit.
■Insert inner members of slides into the already mounted
internal slide members in the rack.
■Attach left and right front mounting ears to vertical
mounting rails.
■Tighten the screws.
■Installation completed.
4
5
Model No : NBK-01

P. 11
2.1 Connection Diagram Chapter 2
NCP-1716 Ethernet Console
Hub
Router
Switch
PDU
UPS
Power module
Serially
managed device
SG-100F
RJ45-DB9
female adapter
SG-100M
RJ45-DB9
male adapter
Cat5 cable Cat5 cable Cat5 cable
Internet Hub
for
remote access
Headless servers

2.2 Membrane Chapter 2
Power ON
■Turn off all devices / servers and Cat5 IP serial console
■Make sure all cables / connectors are properly connected
16 ports
Port activity Status LEDs Reset button
Power Red: Power on indication
Link Orange: 10BaseT Etherent connection
Green: 100BaseT Ethernet connection
Ready Green: Blinking per second when system is busy
Port LED Green: Traffic activity
Reset button Press reset button to reboot the unit
P. 1 2
Front Panel - Port LED Indications
Warning :
Press “Shift+Esc” sets default, it will change the pre-set operating parameters and local access “Per-
sonality”, Please refer to FAQ (page 29-30) for detailed setting.

P. 1 3
2.3 Configuring the Local Console Chapter 2
Saving and exiting SETUP
The first menu seen when entering SETUP mode serves as a directory to the other SETUP menus. When
you depress F12 to exit Setup, you will return to this main directory and be given the option of saving your
selections.
The highlighted field at the right of the screen gives you the choice of saving or not saving parameter changes
in the nonvolatile memory before returning the terminal to the normal operating mode. If you don’t save your
setting before you leave the SETUP mode, any new selections will be lost when you power down the console
terminal drawer.
To save your SETUP selection, depress the Spacebar to change the save field at the right side of the screen
from NO to YES before exiting SETUP.
Depress F12 to exit SETUP mode and return to the normal display mode.
Entering SETUP
Hold down the Alt key and then depress the Esc key to enter SETUP mode.
When you enter SETUP mode, any text on the screen temporarily disappears, and the main SETUP directory
appears. When you leave the SETUP mode, the main SETUP directory disappears, and any text that was
on the screen reappears.
F1
Disp
Setup
( F1-F11 Selects menu; Shift+Esc sets defaults )
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Save ?
( SPACE toggles )
F9
Lan
F10
Colr1
F11
Colr2
F12
Exit
F7
Fkeys
F8
Ansbk
F3
Keybd
F4
Comm
F5
Misc
F6
Tabs
F2
Genrl
Switch on the power on the rear of NCP-1716.
(It takes about 60 seconds to initialize the device. Please do not input any key while initalize the device)
FDX 1-1
Caution: Scroll lock must be off for accessing setup menu by “Alt + Esc” key

1. Select the access port and configure each setting & type in the value for Inactivity timeout
2. Press SPACE bar to select other itemts
3. Complete the confiuration, and select <Yes> to confirm
The 16-port serial console drawer with serial-to-serial local access function which the data transfer can be between
one designated serial port (ESP) and one of the other serial ports.
FDX 1-1
FDX 11-59
IPCS Version 1.0 & 06/11/20
===============================================================
[StoS]
Serial to serial Conguration
Connect to [ 1]
Inactivity timeout [0 ]
Baud rate [9600 ]
Data bits [8bits]
Parity [None]
Stop bits [1bits]
Flow controls [None ]
Press: Space to select
TAB, ENTER:netx eld, ‘<’:left, ‘>’:right, ‘q’ or ESC:abort
FDX 11-59
IPCS Version 1.0 & 06/11/20
===============================================================
[StoS]
Serial to serial Conguration
Serial to serial Conguration
Connect to [ 1]
Inactivity timeout [0 ]
Baud rate +-conrm?-+ [9600 ]
Data bits |<YES> NO | [8bits]
Parity +----------+ [None]
Stop bits [1bits]
Flow controls [None ]
Press: Space to select
TAB, ENTER:netx eld, ‘<’:left, ‘>’:right, ‘q’ or ESC:abort
2.3 Configuring the Local Console Chapter 2
P. 1 4

2.3 Configuring the Local Console Chapter 2
4. Type in user name and password. The default login name & password are “root”
User Default
Name Password
root root
5. Press Ctrl and Ckeys to get out of Serial-to-Serial function and back to main console screen.
P. 1 5

2.4 Changing Operating Parameters Chapter 2
P. 1 6
To select one of the setup menu’s shown, press the indicated function key.
- The screen for that menu appears with the name highlighted.
- The fields in the middle of the screen, indicate the parameters that you can change in
that menu.
- The top line identifies the keys you press to highlight the parameter fields and change
the settings. The procedure is:
(1) Use arrow key to highlight the parameter field you want to change.
(2) Use the Spacebar to change the parameter.
F12 always returns you to the top menu.
The following tables list the parameters for each menu and explains their settings.
Default settings are listed first unless otherwise noted.
Columns Sets the screen display for 80 columns, 132 columns, or Econ-80.
(80 columns with more pages of memory)
Lines Sets the screen display for 24, 25, 42, or 43 lines.
(25 lines is normally required for PC Term.)
Page Length Sets the length of a page of display memory to:
1 x Lines: Equal to the number of lines selected in the lines parameter
2 x Lines: Two times the value of the lines parameter
4 x Lines: Four times the value of the lines parameter, or
*Equal to the value of the lines parameter, with a second page containing the rest of the
lines remaining in memory.
Cursor Sets the cursor display to blink or steady, block or underline.
Background Sets the screen display to Dark (light characters on a dark background) or
Light (dark characters on a light background).
Auto Page Cuses a new page of memory to move onto the screen when the cursor reaches the top
or bottom of the page.
Screen Saver Off, 1, 2, 3, 4, 5, 6, means no saver, 5, 10, .... minutes saver.
Width Change Causes the terminal to clear the screen when executing a command to change the num-
Clear ber of columns.
Reverse Off / On control function ANSI, VT-100 and VT-220:
"Off" means, when SGR command ESC [ 3? m and ESC
[ 4? m select background and foreground color change respectively.
"On" means, when SGR command ESC [ 3? m and ESC
[ 4? m select foreground and background color change respectively. (? can be 0,1,2,...,7)
Display Preset with LCD
F1 Display Setup Menu
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------