NTI RACKMUX-V17-N User manual

RACKMUX-V15/17
RACKMUX-D17
Rackmount Drawer with Keyboard, LCD
Monitor and Mouse
Installation and Operation Manual
RACKMUX®Series
RACKMUX-V17-N (Front and Rear View)
MAN047 Rev Date 10/18/2017

TRADEMARK
RACKMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.
COPYRIGHT
Copyright © 2007, 2014 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the
right to make changes in the product design without reservation and without notification to its users.
Typographic Conventions
The following table describes the typographic changes used in this instruction.
Typeface
Meaning
Example
AAaaBBaaCCcc123
On-screen computer output
C:>
AAaaBBaaCCcc123
What you type, contrasted with on-screen
computer output; keyboard keys to press
C:> L
Press the Fn key
i

TABLE OF CONTENTS
Introduction ...................................................................................................................................................................... 1
Features and Functions ................................................................................................................................................... 2
Installation ....................................................................................................................................................................... 3
Rack Mounting Instructions ......................................................................................................................................... 3
Extension Bracket Method ........................................................................................................................................ 3
One-Man Installation Method .................................................................................................................................... 4
Optional Telco 2-Post Mounting ............................................................................................................................... 7
Connect to a CPU ........................................................................................................................................................ 8
Connect Extra Device .................................................................................................................................................. 9
Connect Power .......................................................................................................................................................... 10
Power Up ................................................................................................................................................................... 10
Display Functions .......................................................................................................................................................... 11
Standard Controls ...................................................................................................................................................... 11
OSD Control Menu- 15 and 17 Inch VGA models (-V15/-V17) ................................................................................. 11
OSD Main Menu ..................................................................................................................................................... 11
Brightness/Contrast Menu ...................................................................................................................................... 12
Color Menu ............................................................................................................................................................. 12
Position Menu ......................................................................................................................................................... 12
Setup Menu ............................................................................................................................................................. 13
OSD Control Menu-DVI Model (-D17) ....................................................................................................................... 13
OSD Main Menu ..................................................................................................................................................... 13
Brightness/Contrast Menu ...................................................................................................................................... 14
Setup Menu ............................................................................................................................................................. 14
OSD Control Menu- 17 Inch Hi-Resolution Model (-HR) ........................................................................................... 15
OSD Main Menu ..................................................................................................................................................... 15
Keyboard Functions ...................................................................................................................................................... 17
Function Key Operation .......................................................................................................................................... 17
Number Pad ............................................................................................................................................................ 18
Other Uses of the Function Key .............................................................................................................................. 19
Numeric Keypad Option ............................................................................................................................................. 20
PS/2-USB Keyboard/Mouse Mode ............................................................................................................................ 21
Korean keyboard option ................................................................................................................................................ 22
SAFETY ......................................................................................................................................................................... 23
Rackmux-KVM Drawer Standard Specifications ........................................................................................................... 24
General Specs ........................................................................................................................................................... 24
LCD – 15” ................................................................................................................................................................... 24
LCD – 17” ................................................................................................................................................................... 24
LCD – 17” Hi-Resolution ............................................................................................................................................. 24
Display Controller: VGA (-15 & -17) .......................................................................................................................... 25
Display Controller: DVI (-17) ...................................................................................................................................... 25
OSD Control Board .................................................................................................................................................... 25
Keyboard.................................................................................................................................................................... 25
Touchpad ................................................................................................................................................................... 25
Troubleshooting ............................................................................................................................................................. 26
Index .............................................................................................................................................................................. 26
Warranty Information ..................................................................................................................................................... 26
ii

TABLE OF FIGURES
Figure 1- Mount RACKMUX to a standard rack ................................................................................................................................. 3
Figure 2- Adjustable rail depth ........................................................................................................................................................... 4
Figure 3- Install cage nuts .................................................................................................................................................................. 4
Figure 4- Install rail assemblies ......................................................................................................................................................... 5
Figure 5- Adjust distance between rails ............................................................................................................................................. 5
Figure 6- Slide the RACKMUX into the rails ...................................................................................................................................... 6
Figure 7- Secure the RACKMUX ....................................................................................................................................................... 6
Figure 8- Position RACKMUX with clearance to open ....................................................................................................................... 7
Figure 9- Mount to Telco post with optional mounting brackets ......................................................................................................... 7
Figure 10- Connect a PS/2 CPU ........................................................................................................................................................ 8
Figure 11- Connect a USB CPU ........................................................................................................................................................ 8
Figure 12- Cables used for RACKMUX with DVI video support ......................................................................................................... 9
Figure 13- Connect a USB 1.1 device to the front (optional).............................................................................................................. 9
Figure 18- Connect the power cord ................................................................................................................................................. 10
Figure 19- OSD Controls ................................................................................................................................................................. 11
Figure 20- US(English) Keyboard Layout ........................................................................................................................................ 17
Figure 21- Keyboard LED Indications .............................................................................................................................................. 17
Figure 22- Keys of the Number Pad ................................................................................................................................................ 19
Figure 23- Additional multi-function keys ......................................................................................................................................... 19
Figure 24- U.S. (English) keyboard with numeric keypad ................................................................................................................ 20
Figure 25- U.K. (English) keyboard with numeric keypad ................................................................................................................ 20
Figure 26- German keyboard with numeric keypad ......................................................................................................................... 21
iii

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
INTRODUCTION
The RACKMUX-V15/17 Drawer (RACKMUX) consists of a Keyboard, Touchpad, and LCD monitor integrated into a 1RU
rack-mountable drawer with wrist pads. When access to a server rack is needed, the drawer can be pulled out and the display
lifted up like a notebook computer, revealing the keyboard and mouse. When the drawer is not in use, the display can be folded
forward and down so the 1RU drawer can be pushed into the cabinet easily and smoothly, helping to organize and streamline
busy server rooms. The NTI RACKMUX product line offers a range of KVM Drawer solutions ideal for rack and server
management applications, which will ensure reliability and serviceability.
The RACKMUX will switch between USB and PS/2 standards for versatile connection to a CPU. The forward-folding LCD
monitor is offered in either 15” or 17” (designated in the product name as -15 or -17) and the video format can be either VGA or
single-link DVI (designated by –V or –D: example RACKMUX-V15). For user input, the drawer offers a notebook-style keyboard,
wrist-pad, and a three-button touchpad. The keyboard and mouse can be connected using USB and PS/2 cables. USB and PS/2
interfaces will remain active at all times and the keyboard and mouse can be switched, at any time, to use either one. The
RACKMUX-V15/-V17 also provides a front panel USB 1.1 port for the connection of an external USB device (such as a flash
drive).
The keyboard and mouse interface is compatible with Windows platform CPUs. This multiple interface capability reduces
equipment costs by ensuring that a single console is compatible with various PC/server input devices.
Installing the RACKMUX into any server environment will offer:
• A space saving 1RU design, easily mountable in any 19” cabinet/rack
• A forward-folding 15” or 17” TFT LCD with built-in OSD menu for screen adjustments
• Auto shut-OFF switch: Turns OFF the power to the monitor when the LCD is in a folded-closed position.
• Built-in 83-key (US) or 84-key (Europe) keyboard with wrist pad
• Standard 3-button mouse touchpad
• Support for PS2 and USB connections for the keyboard and mouse.
• Support for VGA (15” or 17” model) or single-link DVI signals (17” model only)
• Front-access USB port for easy accessory USB 1.1 device connection
• An internal cable arm for proper cable management when sliding the drawer open and closed
• Added security with a drawer lock to prevent unwanted access
• Locking rails to prevent movement of the drawer when fully extended
• Built-in universal (100-240VAC) low power consumption power supply
• Multi-language support including: US(English), UK(English), German, French, Italian, Spanish
Materials Included with this kit:
 NTI RACKMUX-V15/17 Drawer with VGA Video support
~or~
 NTI RACKMUX-D17 Drawer with DVI Video support
 2 Keys for Lock
 2 Rear Mounting Brackets w/nuts
 8 #10-32x3/4” screws and cage nuts for mounting to a rack
 IEC Power Cord- country specific
 USB-AB-2M 2 meter USB Type A male-to-USB Type B male cable
 VEXT-THN-6-MM 6 foot VGA video cable (models with VGA Video support only)
 DVI-DS-2M-MM 2 meter DVI video cable (model with DVI Video support only)
Alternative Cables (not supplied): (available in 3,6,10 and 15 foot lengths)
VKMEXT-xx-MM for VGA Monitor and PS2 Keyboard and Mouse input
USBVEXT-xx-MM for VGA Monitor and USB Keyboard/Mouse input and USB device support
where:
xx is the length of the cable in feet
MM indicates male-to-male connector
Option:
• Trackball option- for a RACKMUX with a trackball instead of a touchpad- add “T” to the part number (i.e. RACKMUX-V17-T)
• Numeric keypad option- for a separate 17-key numeric keypad, add “-N” to the part number (i.e. RACKMUX-V17-N)
• Hi-Resolution Monitor- for a 17” RACKMUX with hi-resolution monitor (1920 x 1200)- add “HR” to the part number (i.e.
RACKMUX-V17HR (available on 17” models only))
Cables can be purchased from Network Technologies Inc by calling
[phone] (800-RGB-TECH) in the US and Canada or (330) 562-
7070 (worldwide).
1

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
FEATURES AND FUNCTIONS
1. Power Button-press to turn the LCD monitor ON and OFF
2. Power LED- Indicates operation status
Green = Power-ON, Video Input Signal OK
Red = Suspend / Stand-by, or no Video Input Signal
3. Menu Button- press to turn ON the OSD menu
4. Up Arrow Button- press to move the cursor in the OSD menu up
5. Down Arrow Button- press to move the cursor in the OSD menu down
6. Select Button- press to select a menu item (when OSD menu is ON) or press to auto adjust the video quality (when OSD
menu is OFF)
7. NumLock LED- illuminates when the number lock is ON
8. CapsLock LED- illuminates when CapsLock is ON.
9. Scroll Lock LED- illuminates when the Scroll Lock keyboard feature is ON.
10. Fn LED- illuminates when Function Features (page 17) are enabled.
11. USB LED- illuminates when RACKMUX drawer is in USB mode
12. PS/2 LED- illuminates when RACKMUX drawer is in PS/2 mode
13. 3-button mouse- for controlling mouse movements on the monitor and controlling the computer
14. Keylock- to prevent unauthorized use of the RACKMUX
15. Auto Shut-OFF- switch automatically shuts OFF the LCD display when the monitor is folded down
16. keyboard- for manual data entry and computer control
17. USB Port- USB Type A female- for connection of any USB 1.1 compatible device (such as a flashdrive, printer, etc)
18. LCD Display- for viewing the video signal from the connected CPU
19. IEC Connector- for attachment of the IEC power cord to power the RACKMUX drawer
20. Switch- for powering ON and OFF the RACKMUX drawer
21. Video In-21A. 15HD Female- for connection of the VGA video cable from the CPU (only in models that support VGA video)
21B. DVI-D Female- for connection of a DVI-D video cable from the CPU (only in models that support DVI)
22. USB- USB Type B female- for connection of the USB cable from a USB CPU
23. Keyboard Connector- purple 6 pin miniDIN female- for connection of the PS/2 keyboard cable from a PS/2 CPU
24. Mouse Connector- green 6 pin miniDIN female- for connection of the PS/2 mouse cable from a PS/2 CPU
Front View
RACKMUX-V17
Rear View
RACKMUX-V17
24
18
16 14
15 1A
9
8
7
Fn
10
17
11 12
PS/2
13
1
2
3
4
5
6
19 22
2320
(RACKMUX-D17)(RACKMUX-V17)
21A 21B
- or -
2

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
INSTALLATION
Rack Mounting Instructions
The RACKMUX was designed to be mounted to a rack and includes mounting flanges to make attachment easy. The rails that
are provided for rack mounting will either be empty studs for insertion through slots in a rear extension bracket, or rail guides for
one-man installation to a front and rear bracket set. Depending upon the method provided, install your RACKMUX according to
the instructions below.
Extension Bracket Method
1. Determine the mounting height in the rack for the drawer. It should be a height comfortable to use the keyboard and see the
LCD display. Mark holes in each of the 4 corner cabinet rails at points all level with each other.
2. Secure the rear brackets to the rear rack cabinet rails. Apply the top screws (supplied) for each bracket to the holes marked in
step 1.
3. Lift the keyboard into position and line the studs on the left and right sides up with the slotted openings in the rear bracket.
Apply the nuts (supplied) to the studs but do not tighten the nuts yet.
FYI: There are 4 mounting studs provided on each side of the RACKMUX. Depending on the depth of the rack and
distance apart of the cabinet rails, the position of the rear bracket may make all 4 studs available for use. In this case,
apply the 2 nuts to the studs furthest apart from each other on each side.
4. Slide the drawer in until the top holes in the front bracket flanges line up with the holes marked in step 1. Secure the front
brackets on the drawer to the front cabinet rails with two screws per bracket. Be sure to tighten the screws securely. Then
tighten the nuts applied in step 3.
5. Apply one more screw to each of the rear brackets to finish.
Figure 1- Mount RACKMUX to a standard rack
Apply nuts (supplied) to studs and
secure rear brackets to drawer.
Front bracket
flange on drawer
Rear bracket
flange
Drawer
Front Cabinet
Rail Rear Cabinet
Rail
Rear bracket overlapping
drawer (Rear edge
of drawer)
Stud on drawer
Secure bracket
to rail using two
screws and nuts
(supplied)
Secure bracket
to rail using two
screws and nuts
(supplied)
Stud for mount to
extension bracket
Guide for one-man installation method
3

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
One-Man Installation Method
If you would like to see a video of this installation, see the “single-person-installation” video .
1. Locate and unpack the hardware bag. Your hardware bag will include all items necessary to install the specific RACKMUX
model (see the manual that accompanied your RACKMUX drawer), including the following hardware unique to the Single-Person
hardware installation:
•10- #10-32 cage nut
•2- #10-32 x 1/2” flat-head machine screw
•8- #10-32 x 3/4” pan-head machine screw
To install the rails you will need only a tape measure and Phillips screwdriver.
2. Unpack the left and right rail assemblies. Each are labeled “Right Front” and “Left Front” to indicate their intended position and
orientation. Extend each rail assembly to the dimension required for your rack. Rail assemblies are adjustable to fit within a rack
between 24” and 40” in depth.
Figure 2- Adjustable rail depth
3. Install six #10-32 cage nuts at the front of the rack in positions where the RACKMUX will be mounted (three in each side).
Install four more cage nuts at the rear of the rack in positions straight across from the upper and lower cage nuts installed in front.
Figure 3- Install cage nuts
Rail assemblies are adjustable in length from 24” to 40”.
XXXXX
Labeled
Cage
Nuts
Front Rack
Support
Extender Rail
Rail Flange
Cage
Nuts
Rear Rack
Support
Extender Rail
4

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
4. Install the right rail assembly. The end with the label “Right Front” mounts to the front rack support. Install only the center
screw through the rail flange to the rack support and cage nut using the #10-32 x 1/2” flat head machine screw provided. (See
image below.) Do not tighten at this time. Install the left rail assembly in the same fashion. The end with the label “Left Front”
mounts to the front rack support.
5. Install two #10-32 x 3/4” pan-head screws in the rear of each rail assembly as shown below. Do not tighten at the time.
Figure 4- Install rail assemblies
6. Measure the distance between the inside of the rails at the front of the rack. Adjust the distance to 17-1/4” and tighten the flat-
head screws to the rail flanges securely.
Figure 5- Adjust distance between rails
17-1/4"
Front Rack Supports
Left Rail
Right Rail
Install one flat
head screw in
the center in
each side at the
front
Install two
screws in each
side at the rear
Rack Front
Rack Rear
5

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
7. Lineup the rail guides on the RACKMUX drawer with the slots in the front of the left and right rails and slide the drawer into the
rack. The rail guides should be positioned such that the wide lip of the guide is on the backside of the rail. Slide the drawer in
completely.
View of rail guide from the front of the rack support View of rail guide from the backside of the rail
Figure 6- Slide the RACKMUX into the rails
8. Apply four more #10-32 x 3/4” pan-head machine screws (two for each) through the holes in the drawer flanges, through the
holes in the left and right rails, into the cage nuts in the rack supports. Tighten each securely.
Figure 7- Secure the RACKMUX
9. Tighten securely the four screws applied to the rear rail flanges in step 4.
Rail guides
Wide lip of rail guide
Apply two
more screws
on each side
There should
be a total of
six screws at
the front now.
6

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Note: To provide sufficient room for the LCD monitor to be opened to a proper viewing angle (a minimum 90 degree
position from the keyboard), ensure that all devices mounted above the RACKMUX extend no more than 1.75” from the
rack frame. (See Figure 8)
Figure 8- Position RACKMUX with clearance to open
Optional Telco 2-Post Mounting
If the Telco 2-post mounting bracket kit (NTI# RL-T15-TEL) is to be used, secure the short and long brackets to each side of the
drawer as shown in Figure 9. Apply 2 nuts (supplied) per bracket to secure the brackets to the drawer. Apply two #10-32x3/4”
screws (supplied) per bracket to the post at the desired height. Slots are provided in the brackets to make minor depth
adjustments easy. Be sure to properly tighten all nuts and screws before using the drawer.
Figure 9- Mount to Telco post with optional mounting brackets
Side View of RACKMUX
"X" must be
less than 1.75"
for LCD to open
to full 90
X
90
Server mounted
above RACKMUX
in the same rack
7

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Connect to a CPU
The RACKMUX may be connected to either a PS/2 or a USB CPU with a VGA video port. To connect to a PS/2 CPU, use a
VEXT-6-MM cable and VVKINT-6-MM cable as shown in Figure 10. To connect to a USB CPU, use the VEXT-6-MM and
USB-AB-2M cables(supplied) as shown in Figure 11.
Figure 10- Connect a PS/2 CPU
Figure 11- Connect a USB CPU
8

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
When connecting a CPU with DVI support to the single-link DVI port of the RACKMUX, use a DVI-DS-2M-MM (supplied) for the
DVI video signal, a USB-AB-2M (supplied) for the USB connection, and if using PS/2 keyboard and mouse connections,
connect a VVKINT-6-MM cable (sold separately) between the CPU and RACKMUX.
Figure 12- Cables used for RACKMUX with DVI video support
Connect Extra Device
On the front of the RACKMUX is an additional USB Type A port to be used, if desired, for an extra accessory. Any low or full
speed USB device may be connected to this port to be used. This port is fully compliant with USB standard 1.1.
Note: In order for the optional USB device port to be usable, the USB port on the rear of the RACKMUX must be
connected to a USB enabled CPU (a 2 meter USB cable is supplied).
Note: If a USB keyboard or mouse is connected, operation of the RACKMUX keyboard or mouse may cause
unpredictable results. Do not try to use both mice or both keyboards at the same time.
Figure 13- Connect a USB 1.1 device to the front (optional)
Note: If a USB 2.0 device is connected to the optional USB device port, it will operate at USB 1.1 speed.
CAMERA
PRINTER SCANNER
Connect optional USB 1.1 or 2.0 device
FLASH DRIVE
FRONT VIEW OF RACKMUX-V17
9

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Connect Power
Connect the IEC power cord to the power port as shown below.
Figure 14- Connect the power cord
Power Up
Power up the RACKMUX and connected computer in this order.
1. Power On the RACKMUX
2. Power ON the attached CPU.
If a device is plugged into the USB port on the front of the RACKMUX, it can powered-ON at any time.
Note: During power-up, do not attempt to type or otherwise use the keyboard. Doing so may result in boot errors and
loss of keyboard and mouse.
10

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
DISPLAY FUNCTIONS
An NTI RACKMUX with a 17” monitor supports resolutions up to SXGA (1280 x 1024) and a 15” monitor supports resolutions up
to XGA (1024 x 768), each with a refresh rate at between 55 and 76Hz. The quality of the image on the LCD monitor is adjustable
using an On Screen Display (OSD) menu using the control buttons on the RACKMUX.
Standard Controls
The RACKMUX has 5 standard control buttons and a power LED. The 5 standard control buttons operate as follows:
• The Power button turns the RACKMUX LCD and backlight ON and OFF as desired.
• The Power LED located immediately below the Power button is a dual color
LED. It will illuminate with a green color when the RACKMUX is powered
ON and working properly. It will illuminate with a red color if the RACKMUX
is powered ON but there is no input signal detected.
• The Menu button is used to bring up the OSD menu where the various
settings of the LCD display can be adjusted. Once the OSD screen is
displayed, the Menu button is used to make selections within the menus.
See "OSD Control Menu" (below) for more on LCD display settings.
• The Up and Down Arrow buttons are used to navigate through the menus.
Move the cursor up or down as desired to highlight an item for selection.
Once an item is highlighted, pressing the Menu button will select it.
Figure 15- OSD Controls
• The Select button is used to make selections within the OSD menus when the OSD menu is ON. When the OSD menu is
OFF, the Select button will act as an Auto Adjust button to keep the user from having to use the menus to adjust the quality
of the image on the monitor.
OSD Control Menu- 15 and 17 Inch VGA models (-V15/-V17)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the
OSD Menu, press the Menu button (above). To turn the Menu back OFF, either select "EXIT" from the main menu or just wait
10-60 seconds and it will automatically be cleared from the screen.
OSD Main Menu
Selection
Purpose
Range
Brightness/Contrast
Increase/decrease panel brightness/contrast level
1-100
Color
R,G,B color temperature control
1-100
Position
• Video Image horizontal and vertical position control
• Clock setting
• Phase control
1-100
Setup
• Control OSD Image position on screen
• Set time OSD will stay on screen before auto shutoff
• Select the language of the OSD menu
--
10 to 60 seconds
Several languages (see page 8)
Exit
Exit from the OSD control menu
Power
ON/OFF
Menu
Up Arrow
Select/
Auto Adjust
Power LED
Down Arrow Controls for the
OSD Menus
11

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Brightness/Contrast Menu
Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and contrast levels of
the LCD display. Using the Up or Down Arrows to navigate the menu, highlight either the BRIGHTNESS or CONTRAST
sections and press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting.
Select EXIT when finished to return to the Main Menu.
Color Menu
Selecting the Color menu will bring up a screen in which the user can adjust the Red, Green, and Blue color levels (values from 1-
100) of the LCD display. With the RED, GREEN, or BLUE sections highlighted, (use the Up or Down Arrow to move between
them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting.
Select EXIT when finished to return to the Main Menu.
Position Menu
Selecting the Position menu will bring up a screen in which the user can select AUTO ADJUST to automatically adjust the
horizontal and vertical position of the displayed image on the monitor, as well as adjust the clock and phase settings if they are not
correct. The user can also individually adjust these settings if so desired. With any of the sections highlighted, (use the Up or
Down Arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down
Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main Menu.
12

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Setup Menu
Selecting the Setup menu will bring up a screen in which the user can adjust
 OSD POSITION-the position of the OSD menus on the LCD display
 OSD TIME-the length of time the user can be idle before the OSD menu automatically exits (adjustable from 10
to 60 seconds)
 LANGUAGE-the language that the OSD menus will be presented in
With the item highlighted, (use the Up or Down arrow to move between them), press the Select button to choose the option to
adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main
Menu.
OSD Control Menu-DVI Model (-D17)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the
OSD Menu, press the Menu button (page 11). To turn the Menu back OFF, either select "EXIT" from the main menu or just
wait 10-60 seconds and it will automatically be cleared from the screen. Any changes made before exiting the menu will be
saved.
OSD Main Menu
Note: In order to display the OSD Menu, the RACKMUX must first be connected to a video source (see “Connect to a
CPU” – page 8).
Note: If menu does not appear when the Menu button is pressed, the monitor may be set for a “PC” (VGA) input source.
Press the Up Arrow button on the monitor to switch it to a “Digital” (DVI) input source.
OSD Image can be moved
to different points on the
display
13

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Image can be moved
to different points on the
display
Selection
Purpose
Range
Brightness/Contrast
Increase/decrease panel brightness/contrast level
1-100
Setup
• Control OSD Image position on screen
• Set time OSD will stay on screen before auto shutoff
• Select the language of the OSD menu
• Select Input Source to display
• 0-4
• 10 to 60 seconds
• English, Spanish, German, Italian, or French
• Digital or PC (must be set to Digital)
Exit
Exit from the OSD control menu
Brightness/Contrast Menu
Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and contrast levels of
the LCD display. Using the Up or Down arrows to navigate the menu, highlight either the BRIGHTNESS or CONTRAST sections
and press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting.
Select EXIT when finished to return to the Main Menu.
Setup Menu
Selecting the Setup menu will bring up a screen in which the user can adjust
 OSD POSITION-the position of the OSD menus on the LCD display (positions 0-4)
 OSD TIME-the length of time the user can be idle before the OSD menu automatically exits (adjustable from 10
to 60 seconds)
 LANGUAGE-the language that the OSD menus will be presented in
 INPUT SOURCE- the type of signal that is coming from the CPU, either Digital (DVI) or PC (VGA)
NOTE: As used on this RACKMUX, the INPUT SOURCE must be set to “Digital”.
With the item highlighted, (use the Up or Down Arrow to move between them), press the Select button to choose the option to
adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main
Menu.
14

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Control Menu- 17 Inch Hi-Resolution Model (-HR)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the
OSD Menu, press the Menu button (below). To turn the Menu back OFF, either press the Exit button or just wait
approximately 10 seconds (timing is adjustable) and it will automatically be cleared from the screen. Any changes made before
exiting the menu will be saved.
OSD Main Menu
The Main Menu is broken into five sections, Color, Picture, Function, OSD Menu, and Misc. Press one of the arrow buttons to
move between them. The Picture and Function sections only apply when the RACKMUX is connected as VGA instead of DVI.
To select a menu and move to characteristics within them (i.e. CSM, Brightness, or Contrast under the Picture menu), press the
Select button while the desired menu is displayed.
Characteristics that can be adjusted are described in the chart below.
Selection
Purpose
Range
Colour
Contrast
Brightness
Colour Temp.
Colour Adjust
• Increase/decrease panel contrast level
• Increase/decrease panel brightness level
• Set panel color temperature
• Select RGB balance (goes to submenu)
• 0-100
• 0-100
• 5800K,9300K,6500K,User
• 0-100
Picture (VGA Only)
H Position
V Position
Phase
Clock
Sharpness
• Control Horizontal position of screen
• Control Vertical position of screen
• 0-100
• 0-100
• 0-100
• 0-100
• 1-5
Function (Fx)
(VGA Only)
To manually force auto adjust of monitor settings
Select Auto Adjust or Auto Color functions
15

NTI RACKMUX-V15/17 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Menu
Language
OSD H. Pos.
OSD V. Pos.
OSD Timer
Translucent
• Select the language of the OSD menu
• Control Horizontal OSD Image position on screen
• Control Vertical OSD Image position on screen
• Control if OSD will time out
• Adjusts how boldly the menu is displayed
• English, Spanish, German, Italian, or French
• 0-100
• 0-100
• On/Off If On, select 3-100 seconds.
• -/+
Misc.
• Select Input
• Reset monitor to default settings
• VGA or DVI
• Yes/No
Press the Exit button or select “Exit” to exit the OSD menu.