auto maskin Marine Pro RIO 216 User manual

Manual# 1100373
Quick Installation Guide
RIO 216
I/O Expansion Unit

Quick Installation Guide
for
RIO 216 –I/O Expansion Unit
~~~
Revision
1.1
Revised
November 18, 2015
Revision history:
Rev.
Date
Description
1.0
Nov.2013
Initial realised revision
1.1
18.11.15
Minor updates

Page ii
Quick Installation Guide
Copyright
© 2010 - 2015 by Auto-Maskin AS.
All rights reserved. No part of this document may be reproduced or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Auto-Maskin AS.

Quick Installation Guide
Page iii
Table of Content
DOCUMENT INFORMATION ................................ 1
ABOUT THIS MANUAL .............................................. 1
Responsibilities .............................................. 1
ORDERING INFORMATION......................................... 1
INSTALLATION OF THE RIO 216 ........................... 2
INTRODUCTION ...................................................... 2
OPERATING CONDITIONS.......................................... 2
WIRING ................................................................ 2
Power Supply ................................................. 2
Communication to the DCU ........................... 3
CONFIGURATION .................................................... 4
PIN LAYOUT......................................................... 5

Quick Installation Guide
Page 1
Document
Information
About this manual
This manual has been published
primarily for professionals and
qualified personnel.
The user of this material is assumed to
have basic knowledge in marine
systems, and must be able to carry out
related electrical work.
Work on the low-voltage circuit should
only be carried out by qualified and
experienced personnel.
Installation or work on the shore
power equipment
must only be carried
out by electricians authorized to work
with such installations.
Responsibilities
It is the sole responsibility of the
installer
to ensure that the installation
work is carried out in a satisfactorily
manner, that it is operationally in good
order, that the approved material and
accessories are used and that the
installation meet all applicable rules
and regulations.
Note! Auto-Maskin continuously
upgrades its products and reserves the
right to make changes and
improvements without prior notice.
All information in this manual is based
upon information at the time of
printing.
For updated information, please
contact your local distributor.
Ordering information
The Marine Pro covers a wide range of
compatible products within both the
200- and 400 Series. Please visit our
web site for more information.
http://auto-maskin.com/marine/

Page 2
Quick Installation Guide
Installation of
the RIO 216
This chapter covers installation of the
RIO 216
Introduction
The RIO 216 is an I/O expansion
module providing 16 digital inputs.
Using the two-wire J1939 interface, it
communicates its measured data to a
DCU in the Auto-Maskin Marine Pro
range.
The unit can also be used standalone
and communicate its data to J1939
compatible devices.
Operating Conditions
Operating Temperature:
-40 to +70 °C
Wiring
The RIO 216 has these main
connections
24VDC Power Supply
Communication to the DCU
Digital Inputs
Power Supply
DC Power Supply
On the RIO 216, connect a DC power
supply to pin 6 (positive) and pin 5
(negative) on the Grey Receptacle.
Ground
On the RIO 216, connect ground to pin
4 on the Grey Receptacle.
Power Supply Fuse
The RIO 216 module shall be
protected with an external 2A fuse on
the supply line.
Wire Requirement
Supply wires shall have a minimum
area of 1mm2(~17 AWG) with a rating
of 70°C or better.

Quick Installation Guide
Page 3
Communication to the
DCU
The RIO 216 comes preconfigured to
communicate with the DCU 410/408
or DCU 210/208 in the Auto-Maskin
Marine Pro range.
It can be used together with other RIO
expansion modules.
Note! The RIO 216 shall be connected
to the DCU J1939 interface
Note! You can only have one RIO 216
connected to your system. Two units
are only supported by the DCU
410/408 with the CANopen port
configured to J1939
Communication Wiring
Connect the two wires in the shielded
communication cable as follows:
The 400 Series
DCU 410/408 wire
terminals (COM 4)
RIO 216 wire
terminals (Grey
Receptacle)
49 (GnD)
3
50 (L)
2
51 (H)
1
DCU 410/408 wire
terminals (COM 5)
RIO 216 wire
terminals (Grey
Receptacle)
46 (GnD)
3
47 (L)
2
48 (H)
1
Note! Only supported if CANopen is
configured to J1939
The 200 Series
DCU 210/208 wire
terminals
RIO 216 wire
terminals (Grey
Receptacle)
25 (GnD)
3
26 (L)
2
27 (H)
1
Communication bus
termination resistor
Note! Do not skip this section!
A 120 ohm (1/4 W) termination
resistor shall be connected in both
ends of the J1939 bus.
When the bus is properly connected,
the measured impedance between bus
terminals 2 and 3 shall be 60 ohm
(+/- 5 ohm).
Is the DCU communicating
with the RIO 216?
This can be verified in the DCU web
server or user interface under the
Troubleshooting menu. Look J1939
under the Communication section.
Note! The J1939 troubleshooting may
not indicate communication to the RIO
216 as other devices on the J1939 bus
will show activity.

Page 4
Quick Installation Guide
Modbus
Reference
The RIO 216 is not directly addressed,
but is available through the DCU J939
Modbus section as J939 “
Auxiliary IO
Number 1” (SPN 702) - “Auxiliary IO
Number 16” (SPN 716).
For the DCU Modbus I/O list, go to
https://docs.google.com/spreadsheet
/ccc?key=0Ao77erHB5iQKcFh3NFdLX1
ZoOUZkNWtLUXlranJWUUE&hl=en#gid
=5
Configuration
The RIO 216 comes preconfigured to
transmit J1939 PGN 0xFED9.
The DCU must be configured using the
web interface in order to read the
status of the digital inputs from the
RIO 216.
Configuration using the DCU
Web Server
Enter the J1939 section in the DCU
web server. Enter each channel’s SPN#
and apply the desired configuration.
Pin and Channel layout
RIO 216
Pin #
Digital
input #
J1939
SPN#
7 (Grey)
1
701
8 (Grey)
2
702
9 (Grey)
3
703
10 (Grey)
4
704
11 (Grey)
5
705
12 (Grey)
6
706
1 (Black)
7
707
2 (Black)
8
708
3 (Black)
9
709
4 (Black)
10
710
5 (Black)
11
711
6 (Black)
12
712
7 (Black)
13
713
8 (Black)
14
714
9 (Black)
15
715
10 (Black)
16
716

Quick Installation Guide
Page 5
Pin Layout
The following tables illustrate the pin
layout for the two RIO 216 Deutsch
connectors.