AutoJoe ATJ-CA100 User manual

CORDLESS
DIGITAL INFLATOR
140 PSI | 2000 mAh | 4 NOZZLES
POWER BANK + FLASHLIGHT
Model ATJ-CA100
EN
Form No. ATJ-CA100-880E-M
If you have any questions or comments, please call the
Snow Joe®+ Sun Joe®customer service department at:
1-866-SNOWJOE (1-866-766-9563)
© 2021 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1

IMPORTANT!
Safety Instructions
mWARNING! Read all safety warnings,
instructions, illustrations and specications
provided with this device.
General Safety
mWARNING! When using the device,
basic safety precautions should always be
followed. Failure to follow all instructions listed
below may result in electric shock, re and/or
serious injury.
• Work area – Keep your work area clean and
well lit.
• Device condition – Keep the device dry,
clean and free from oil and grease.
• Explosion hazard – Do not operate the
device in explosive atmospheres, such as in
the presence of ammable liquids, gases or
dust.
• Bystanders – All bystanders, children and
pets should be kept a safe distance away
from the work area.
• Stay alert – Remain alert at all time, use
common sense and do not operate the
device when tired, or under the inuence of
drugs or alcohol.
• Dress properly – Do not wear loose clothing
or jewelry. They can get caught in moving
parts. Non-slip footwear are recommended
when working outdoors.
• Do not overreach – Keep proper footing and
balance at all times.
• Usage – Do not use this device for any use
case exept for which it was intended.
• ON/OFF – Do not attempt use the device if it
fails to turn on or o
• Storage – When idle, store out of the
reach of children and do not allow persons
unfamiliar with the device or these
instructions to operate it.
• Accessories – Use the device and any
accessories in accordance with these
instructions, taking into account the working
conditions and the work to be performed
Electrical and Battery Safety
mWARNING! Do not expose the device
to rain or wet conditions. Water entering the unit
may damage the device and increase the risk of
electric shock.
mCAUTION! Recharge only with the
charging cable specied by the manufacturer
• Do not abuse the cable – Never carry the
device by the cable or yank the cable to
disconnect it from the outlet. Keep the cable
away from heat, oil, and sharp edges.
• Charging – Do not leave the device
unattended when it is plugged into an
electrical outlet. Turn o the device, and
unplug it before leaving.
mWARNING! Under abusive conditions,
liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, ush with
water. If liquid contacts eyes, seek additional
medical help. Liquid ejected from the battery
may cause irritation or burns.
mWARNING! Do not use the device if
damaged or modied. A damaged or modied
device may exhibit unpredictable behavior
resulting in re, explosion or risk of injury.
mWARNING! Do not expose the device to
re or excessive temperatures. Exposure to re
or high temperatures may cause an explosion.
NOTE: Follow all charging instructions and do
not charge the device outside the temperature
range of 41°F – 105ºF (5°C – 40.5°C). Do not
charge the battery outside in freezing weather;
charge it at room temperature.
mWARNING! Do not touch the inator or
its charging cords with wet hands.
mCAUTION! To reduce the risk of burns,
do not open, crush, heat above 122°F (50°C) or
incinerate.
2

Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read,
understand, and follow all instructions on the machine before attempting to assemble and operate.
Symbols Descriptions Symbols Descriptions
READ THE
OPERATOR'S MANUAL
Read, understand, and
follow all instructions in
the user manual before
attempting to assemble
and operate.
SAFETY ALERT –
Indicates a precaution,
a warning, or a danger.
WARNING! Do not
expose the unit to rain or
wet conditions. Keep dry.
RISK OF BURSTING –
Do not operate inator to
result in output pressure
greater than marked
maximum pressure of
attachment. Do not use
at pressure greater than
140 PSI.
WARNING! Do not direct
air stream at persons or
pets.
WARNING! Do not
expose the unit to rain or
wet conditions. Keep dry.
3

1. LED light
2. Air outlet
3. Barrel jack
4. USB-C port
5. USB-A port
Know Your Cordless Digital Inator
Read the owner’s manual and safety rules carefully before using your Cordless Digital Inflator.
Compare the illustration below to the actual unit in order to familiarize yourself with the location of the
various controls and attachments. Save this manual for future reference.
Technical Data
Pump ........................................................... 40 W
Battery Capacity .................................. 2000 mAh
Input ........................................5V DC | 2A USB-C
12V DC plug
Output ............................5V DC | 2A | 4Ah USB-A
Ination Pressure Max.*............................ 140 PSI
Working Pressure ....................................... 60 PSI
Duty Cycleɫ.................................................10 min
Ination Rate ..........................0.4 CFM (10 L/min)
Net Weight .................................... 1.3 lbs (0.6 kg)
11
21
14
20
3
4
5
BOTTOM
7
8
9
10
12
13
15
16
618
17
19
22
6. PSI volume buttons
7. Tapered nozzle
8. Short tapered nozzle
9. Sports ball needle
10. Presta valve adapter
11. Barrel plug
12. USB-C plug
13. Air hose
14. Air chuck
15. USB-A plug
16. 12V DC plug
17. Mode button
18. Power button
19. LED button
20. LCD display
21. Inator
22. Storage bag
*The device will automatically turn o after 15 minutes due to overheating. | ɫDo not operate for more than 10 minutes at a time, after
which it must be switched o and allowed to cool down for at least 15 minutes before restarting.
1
2
4

Unpacking
Carton Contents
• Inator
• Air hose
• Tapered nozzle
• Short tapered nozzle
• Sports ball needle
• Presta valve adapter
• Storage bag
• 12V DC plug
• USB-A to USB-C cable
• Manual and registration card
1. Carefully remove the inator and check to
see that all of the above items are supplied.
2. Inspect the product carefully to make sure
no breakage or damage occurred during
shipping. If you nd damaged or missing
parts, DO NOT return the unit to the store.
Please call the Snow Joe®+ Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563).
NOTE: Do not discard the shipping carton
and packaging material until you are ready
to use your new cordless digital inator. The
packaging is made of recyclable materials.
Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging
material are not toys. Do not let children play
with plastic bags, foils, or small parts. These
items can be swallowed and pose a suocation
risk!
Charging over USB
NOTE: This power station should be fully
charged before use or storage. Check the battery
level indicator for the remaining charge in the
battery.
Using the included USB-A to USB-C cable,
plug the smaller USB-C connector into the
corresponding USB-C port of inator. Then
plug the other end of the cable (USB-A) into a
USB port on your vehicle, or alternatively into a
USB adapter (not included) for charging at an
electrical outlet (Fig. 1).
NOTE: To maximize charging speed, use a USB
adapter rated at 10W or higher.
NOTE: You may also use other USB ports such
as those on computers, wall outlets and power
banks to charge your inator.
Power over 12V DC
NOTE: The 12V DC auto power cable only
provides working power to the device and does
not charge the internal battery. To charge the
battery use the USB-A to USB-C cable instead.
Using the included 12V DC auto power cable,
plug the barrel plug into the barrel jack of the
inator. Then plug the 12V DC plug into the 12V
DC socket of your vehicle (Fig. 2).
Battery Level Indicator
The battery level indicator can be found on the
LCD display, which will illuminate and indicate
the charge level when the unit is being used, and
when the unit is being charged.
• The three bars on the indicator corresponds
to low, medium and high.
• The three bars will cycle on from left to right
while charging.
Fig. 1
USB-C
USB-A
USB adapter
Fig. 2
12V DC socket
12V DC
plug
5

• Once the battery is fully charged, the three
bars will remain static at which point unplug
the USB-A to USB-C cable from the inator.
NOTE: Timely recharging of the tool will help
prolong its battery life.
mWARNING! The chargers do not
automatically turn o when the battery is fully
charged. Please take care not to leave the
inator plugged in. Unplug the charging cables
when charging is complete.
IMPORTANT! Never allow the tool to become
fully discharged as this will degrade the battery
life over time.
mWARNING! Continued and excessive
overuse of the ON/OFF button can permanently
damage the lithium-ion battery.
• During the charging procedure, the inator
will feel slightly warm to the touch. This is
normal.
• When no further use is planned for an
extended period of time, disconnect the
charging cable from the unit and the electrical
outlet/12V DC socket.
• Do not use the device while charging.
Battery Charging Tips
To obtain the longest possible battery life, we
suggest the following:
• Store and charge your inator in a cool area.
Temperatures above or below normal room
temperature will shorten battery life.
• Never store the inator with the battery in
a discharged condition. Recharge the unit
immediately after it is discharged.
• All batteries gradually lose their charge. The
higher the temperature is, the faster they lose
their charge. If you store your inator for long
periods of time without using it, recharge the
battery every 6 months. This will extend its
battery life.
NOTE: The inator has been shipped in a low
charge condition and should be fully charged
before use.
Operation
1. To turn on the inator, long press the power
button until the LCD display illuminates
(Fig. 3).
NOTE: The LCD display will automatically turn
o when not in use for 150 seconds or more.
2. Press the mode button to cycle between
4 dierent modes: ball, bicycle, motorcycle
and car (Fig. 4).
3. The +and –buttons allow you to manually
adjust the ination pressure. This determines
the pressure at which the inator will pump
up to. Press either the +or –buttons to
increase or decrease pressure by increments
of 0.5 PSI, or long press to quickly cycle the
psi value up or down (Fig 5).
4. Once the desired PSI has been set, short
press the power button to initiate ination
(Fig. 3).
NOTE: Should the pump fail to reach the desired
pressure setting within 15 minutes, the pump will
automatically shut o.
Fig. 3
Power
button
LCD
display
Fig. 4
Mode
button
Modes
Fig. 5
PSI
volume
buttons
Pressure
in PSI
6

Inating with the Air Hose
Schrader valves (cars, motorcycles and
mountain bikes) can be attached directly to the
air chuck without any additional attachments.
1. Screw the air hose clockwise into the air
outlet of the inator (Fig. 6).
2. Unscrew the valve cap from the valve stem
(Schrader) of your tire (Fig. 7).
3. Place the air chuck onto the threaded valve
stem (Schrader), then press down on the air
chuck clamp to secure the chuck onto the
valve (Fig. 8).
Fig. 6
Air Outlet
Air hose
Fig. 7
Valve stem
(Schrader)
Valve cap
Fig. 8
Air chuck
clamp
Air chuck
Valve stem
(Schrader)
4. Set the appropriate PSI according to
the label on the driver's side door or the
vehicle's user manual. Then short press the
power button to initiate ination (Fig. 3).
Inating with Adapters
The air hose can be used with the provided
adapters to inate a variety of items. To use
the adapters lift up the air chuck clamp, insert
your adapter of choice into the air chuck, then
press down on the air chuck clamp to secure the
adapter in place (Fig 9).
Presta Valve Adapter
Presta valves are commonly used on road bikes
and some mountain bikes. To inate a bicycle
tire, you will need to use the Presta valve adapter
1. Loosen the Presta valve locking nut on your
bike's valve stem (Fig. 10).
2. Thread the female end of the Presta valve
adapter onto valve stem of the bicycle tire.
3. Clamp the end of the air chuck down onto
the Presta valve adapter by pressing the air
chuck clamp down until it locks into place
(Fig. 11).
Air chuck
clamp
Fig. 9 Presta valve
adapter
Sports ball
needle
Short
tapered
nozzle
Tapered
nozzle
Fig. 10
To
loosen
To
tighten
Locking nut
Presta valve
stem
7

4. Set the appropriate PSI according to the
bicycle's tire wall. Then short press the
power button to initiate ination (Fig. 3).
5. After ination, remove the air chuck and
tighten the locking nut (Fig. 10).
Sports Ball Needle
Inate all kinds of sports balls with the Sports
ball needle (Fig. 12).
Tapered Nozzles
Inate small plastic or rubber inatables such
as pool rings, beach balls, air mattresses, travel
pillows and more with either of the two provided
tapered nozzles (Fig. 13).
Air chuck clamp
Fig. 11
Presta valve
adapter
Presta valve
Air chuck
Fig. 12
Sports ball
needle
Air chuck
Fig. 13
Tapered
nozzle/short
tapered nozzle
USB Power Bank
The Cordless Digital Inator may also be used
as a portable battery bank for remote, on-the-
go charging of smartphones, tablets, speakers
and more. Devices may be charged through
the USB-A port (Fig. 14). Charging will start
automatically upon connection.
LED Light
The LED button (labelled ) controls the LED
light on the top of the inator (Fig. 15). Follow the
table below to activate the three dierent modes.
LED Button LED
1st press Solid white
2nd press Slow red blinking
3rd press Fast red blinking
4th press OFF
Fig. 14
USB-A
Fig. 15
LED
button
8

Care and Maintenance
Use the included storage bag to protect the
digital inflator when not in use.
mWARNING! Store the inator away from
hot surfaces or under direct sunlight to reduce
the risk of a short circuit.
mCAUTION! Have your device serviced
by a qualied repair person using only identical
replacement parts.
mWARNING! Do not allow brake uids,
gasoline, petroleum-based products, solvents,
etc., come in contact with plastic parts.
Chemicals can damage, weaken or destroy
plastic, which could result in personal injury.
Disposal
Recycling the tool
• Do not dispose of electrical devices as
unsorted municipal waste. Use separate
collection facilities.
• Contact your local government agency for
information regarding the collection systems
available.
• If electrical devices are disposed of in
landlls or dumps, hazardous substances
can leak into the groundwater and get into
the food chain, damaging your health and
well-being.
Recycling + Disposal
The product comes in a package that protects
it against damage during shipping. Keep the
package until you are sure that all parts have
been delivered and the product is functioning
properly. Recycle the package afterwards or
keep it for long-term storage.
WEEE symbol. Waste electrical
products should not be disposed of
with household waste. Please recycle
where facilities exist. Check with
your local authority or local store for
recycling regulations.
Service + Support
If your Auto Joe™ATJ-CA100 Cordless Digital
Inflator requires service or maintenance, please
call Snow Joe®+ Sun Joe®customer service
at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Model + Serial Numbers
When contacting the company or arranging
service from an authorized dealer, you will need
to provide the model and serial numbers, which
can be found on the registration card. Copy
these numbers into the space provided below.
Record the following numbers from the registration card
of your new product:
Model #:
Serial #:
A T J - C A 1
0 0
9