AutoMotionShade EL-204P-1 User manual

407: R-1: 02/20
Effective Date: Feb 2020
Quick Reference Guide (QRG) #13
Pairing of 2nd Generation RF Transmitters with
Double shafted Motor 4240N, using external RF Receiver Module 216P:
Important: on the back of each transmitter you will find a small hole with a micro push button switch behind, used for
the pairing with Module 216P (see pairing instructions below).
Wall Mount Bracket (included)
EL-203P Single Channel Transmitter with
LED Light; Dimension: 1 1/8” x 2 1/8”
(1
st
generation transmitter has no LED light)
Magnetic
Wall mount
(included with
all transmitters)
EL-204P-1
Handheld
Transmitter
(1-channel)
EL-204P-2
Handheld
Transmitter
(2-channels)
Dimension of all shown
Transmitters: 2” x 5”
EL-204P-6
Handheld
Transmitter
(6-channels)
EL-204P-16
Handheld
Transmitter
(16-channels)
EL-213P “Wizard”
16-Channel handheld and/or
wall mounted RF Remote
Transmitter with LED Display
(1st generation Transmitter
has no LED display)
Dimension: 4 1/4” x 6 1/4

407: R-1: 02/20
Effective Date: Feb 2020
All above transmitters will work with Motor 4240N in conjunction with Module 216P.
Please note that 1st and 2nd generation RF Transmitters are not interchangeable; the external Module 216P only
works with 2nd generation RF Transmitters.
Special Feature: Module 216P gives you the option to control a motor both remotely with an RF transmitter and
by means of a wall switch.
1. Connect the Module output wire (A) to the short Shade power wire (B); if wired switch control is desired,
connect the wire coming from the wall switch that controls the shade to Module wire (C). This wire can be
left unused if no hardwired wall switch control is needed.
2. Ensure the Module is connected to a 12V DC power supply (white wire to ground, black wire to 12V power).
A green light on the Module must be lit. If you do not see a solid green light, the Module is either not
properly powered or the Module may be faulty.
3. On the RF Transmitter, select the channel you want to program by pressing the button of that channel.
4. On the Receiver Module, press the small micro push button (D) with a ball pen point and hold until the color
of the light changes from green to red; now release it and immediately without delay press and hold the
micro push button inside the small hole on the back of the transmitter (using e.g. a paper clip) for few
seconds (on transmitter EL-213P “SET” appears on the display), then release it and immediately press the
stop button on the front of the transmitter.
For internal wiring and limit adjustments of Cellular Shade refer to QRG #21;
to 12VDC Power
(C)
- to wired switch (optional)
External RF Receiver Module EL-216P
(As an option, Module 216P can also be
fitted inside the headrail)
(D)
Micro Push Button
(A)
(B)

407: R-1: 02/20
Effective Date: Feb 2020
Note 1:
To clear or un-pair a single channel on the remote, first select that channel on the remote transmitter, then
press and hold the pair button hole on back of remote for a few second (on transmitter EL-213P “SET” appears
on the display), then press “down” button on front of remote. Now only that single channel is cleared from the
remote. (This procedure only clears that single channel from the remote).
Note 2:
To reverse direction, press and hold the pair button hole on the back of the remote transmitter for two second
(on transmitter EL-213P “SET” appears on the display), then release it and press “up” button on remote.
Note 3:
On 16-channel remote, for any specific shade there are two different buttons on the remote to control this
shade
a. One individual button (that controls this single shade only)
b. All-Shades button (that controls a group of shades including this specific shade).
As a result, when you replace a motor on a shade, you have to program this motor two times with two different
buttons on the same 16-channel remote. The procedure of programming remains exactly the same.
Wiring Diagram
Optional wired switch
Red/Green/Blue wires
BLK/WHT
Cellular Shade
216P
External
Receiver
Box
Power (12VDC)
Power (12V)
BLK/WHT
Green/Blue wires
Green/Blue wires
(Red not used)
Molex Connector
Optional