Autonics KRN1000 Series User manual

LCD Touchscreen Paperless Recorder
KRN1000 SERIES
Thank you for choosing our Autonics product.
Please read the following safety considerations before use.
I N S T R U C T I O N M A N U A L
Input/Output
Input/Output Circuit
Universal input Communication output
Option input/output 1
(alarm output 8 channels)
Option input/output 2
(alarm output 6 channels + digital input 2 channels)
Option input/output 3
(alarm output 6 channels + power for transmitter output)
Option input/output 4
(alarm output 4 channels + digital input 2 channels
+ power for transmitter output)
DAQMaster is the comprehensive device management software for setting parameters and monitoring processes.
DAQMaster can be downloaded from our web site at www.autonics.com.
Comprehensive Device Management Program [DAQMaster]
Error Message
Error message Descriptions
HHHH
When input type is temperature sensor (Thermocouple, RTD) and the measurement value is higher than high-limit value of input
range, it ashes HHHH. It is cleared when the measurement value is within the high-limit range.
When input type is analog (voltage, current (shunt)) and the measurement value is over 10% of high-limit input range, it ashes
HHHH. It is cleared when the measurement value is within 10% of high-limit input range.
LLLL
When input type is temperature sensor (Thermocouple, RTD) and the measurement value is lower than low-limit value of input
range, it ashes LLLL. It is cleared when the measurement value is within the low-limit range.
When input type is analog (voltage, current (shunt)) and the measurement value is over 10% of low-limit input range, it ashes
LLLL. It is cleared when the measurement value is within 10% of low-limit input range.
BURN When input type is temperature sensor (Thermocouple, RTD) and input is break, it ashes BURN.
It is cleared when input is connected.
ASKey When forgetting and entering unvaild password 3 times, “ASKey” appears with error message.
Contact our service center with ASKey.
※Please read “Safety Considerations” in KRN1000 user manual before using.
Case
Communication output
Power supply
Option input/output
Input channels
Item KRN1000 Paperless recorder
04 4 channels
08 8 channels
12 12 channels
16 16 channels
0 None
1Alarm relay output 8 channels
2Alarm relay output 6 channels + Digital input 2 channels
3Alarm relay output 6 channels
+ 24VDC power output for transmitter
4Alarm relay output 4 channels + Digital input 2 channels
+ 24VDC power output for transmitter
S Standard panel installation type
1RS422/485+Ethernet+USB Device
0 100-240VAC 50/60Hz
KRN1000 04 0 1 0 S
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic
loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety
equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, re, or economic loss.
2. The unit must be installed on a device panel before use.
Failure to follow this instruction may result in electric shock.
3. Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock .
4. Do not disassemble or modify the unit. Please contact us if necessary.
Failure to follow this instruction may result in electric shock or re.
5. Check the terminal numbers before connecting the power source.
Failure to follow this instruction may result in re or burning the unit.
Safety Considerations
Warning
1. Do not use the unit outdoors.
Failure to follow this instruction may result in shortening the life cycle of the unit, or electric shock.
2. Use the unit within the rated specications.
Failure to follow this instruction may result in shortening the life cycle of the unit, or re.
3. Do not use water or oil-based detergent when cleaning the unit. Use dry cloth to clean the unit.
Failure to follow this instruction may result in electric shock or re.
4. Do not use the unit where ammable or explosive gas, humidity, direct sunlight, radiant heat, vibration, or impact may be
present.
Failure to follow this instruction may result in re or explosion.
5. Keep dust and wire residue from owing into the unit.
Failure to follow this instruction may result in re or product damage.
6. Check the polarity of the power contact before wiring the unit.
Failure to follow this instruction may result in re or explosion.
Caution
Ordering Information
※Please observe all safety considerations for safe and proper product operation to avoid hazards.
※Safety considerations are categorized as follows.
Warning Failure to follow these instructions may result in serious injury or death.
Caution Failure to follow these instructions may result in personal injury or product damage.
※The symbols used on the product and instruction manual represent the following
symbol represents caution due to special circumstances in which hazards may occur.
User Manual
※The above specications are subject to change and some models may be discontinued without notice.
For the detail information and instructions, please refer to user manual and user manual for communication.
Download manuals from the enclosed CD-ROM or our web site (www.autonics.com).
Item Minimum specications Item Minimum specications
System IBM PC compatible computer with Pentium Ⅲor above Hard disk 1GB+ of available hard disk space
Operations Windows 98/NT/XP/Vista/7/8/10 VGA Resolution: 1024×768 or higher
Memory 256MB+ Others RS232C serial port (9-pin), USB port
Specications
Unit Description
※1: For more information of universal input, refer to ‘ Input/Output’.
※2: The weight includes packaing. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.
Series KRN1000
Power supply 100-240VAC 50/60Hz
Allowable voltage range 85 to 110% of rated voltage
Power consumption Max. 23VA
Screen
Display method 5.6 inch TFT Color LCD
Resolution 640×480 pixels
Adjusting brightness 3-level (Min/Standard/Max)
Input method Touch screen (Pressure sensitive type)
Number of input channels 4 / 8 / 12 / 16 channels
Universal input※1Temperature sensors (thermocouple, RTD), Analog (voltage, current (shunt))
Sampling period 1 to 4-CH: 25ms/125ms/250ms, 5 to 16-CH: 125ms/250ms
(internal sampling period is average movement lter and alarm output operation unit time)
Recording period 1 to 3600 sec
Internal memory Approx. 200MB
External memory SD / USB memory max. 32GB
Dielectric strength 2300VAC 50/60Hz for 1 min (between power terminals and case)
※Except ethernet and USB device
Vibration Mechanical 10 to 60Hz 4.9m/s2in each X, Y, Z direction for 1 hour
Malfunction 10 to 60Hz 1m/s2in each X, Y, Z direction for 10 min
Insulation resistance Over 20MΩ (at 500VDC megger)
Noise immunity Square shaped noise by noise simulator (pulse width 1µs) ±2kV
Time accuracy Within ±2 min/year (available up to 2099)
Protection structure IP50 (front part)
Environ-
ment
Ambient temperature 0 to 50℃, storage: -20 to 60℃
Ambient humidity 35 to 85%RH, storage: 35 to 85%RH
Approval
Weight※2Approx. 1290 to 1400g (approx. 590 to 700g)
1. Sensor input terminal: Connects universal input.
2. Ethernet port: Connector for ethernet cable.
It communicates Modbus TCP.
3. RS422/485 port:
Connects RS422/485 for Modbus RTU communication.
4. Option input/output port: Connects for option input/output (digital
input (non-contact/ contact), alarm output,
power for transmitter).
5. Power input: Power connection (100-240VAC 50/60Hz)
1. Power indicator: Power turns ON and the red LED turns ON.
2. Screen: Measrued value is displayed as trand graph, bar bar graph,
digital gures.
3. Front cover: Open the front cover. There are power switch and, USB
Host/Device, SD card slot.
4. Power switch: Turn ON/OFF the power of KRN1000.
5. USB host port: Connect the USB memory.
It recognizes up to 32GB. When using extension cable,
cable length should be up to 1.5m.
6. USB device port: Used for parameter settings.
7. SD card slot: SD card memory slot. It supports up to 32GB.
8. Stylus pen: Used for touching screen.
※Do not connect the other USB devices except USB memory at USB host
port.
Front part
Rear part
7
8
4
5
6
1
2
3
Dimensions (unit: mm)
144 ● Bracket
15
14
10.4
M4
11.5 69.2
137.5
● Panel cut-out
138 +1.0
0
138 +1.0
0
Min. 175
Min. 175
Type Input/Output type Description
Universal input
Input type
RTD JPt100Ω, DPt100Ω, DPt50Ω, Cu100Ω, Cu50Ω (supplied current: approx. 190µA)
Thermocouple B, C (W5), E, G, J, K, L, L (Russia), N, P, R, S, T, U
Analog Voltage: ±60mV, ±200mV, ±2V, 1-5V, ±5V, -1V-10V
Current: 0-20mA, 4-20mA (measureable when using 250Ω shunt resistance)※1
Input impedance Voltage (V): Approx. 205kΩ
RTD, Thermocouple, Voltage (mV): Min. 200kΩ
Display
accuracy※2
RTD Warm-up time: Max. 30 min
At room temperature (25±5℃): ±0.1% F.S.±1-digit
Out of room temperature: ±0.2% F.S.±1-digit
Thermocouple
Analog
Resolution 16-bit
Option
input/output※3
Digital
input
No-contact input ON: Residual voltage max. 1V, OFF: Leakage current max. 0.1mA
Contact input ON: Max. 1kΩ, OFF: Min. 100kΩ, Short-circuit: Approx. 4mA
Alarm relay
output
Capacity 250VAC 3A, 30VDC 3A, 1 Form A (resistive load)
Life cycle Mechanical: Min. 20,000,000 operations
Electrical: 100,000 operations (3A 250V AC, 3A 30V DC)
Power output for transmitter※424±2VDC, Max. 60mA ※Built-in over current protection circuit
Communication
output※5
RS422/485 Modbus RTU ※It is recommended to use shielded cable over AWG 24.
Ethernet IEEE802.3 10 BASE-T / IEEE802.3U 100 BASE-TX (Modbus TCP)
USB Device USB V2.0 Full Speed (Modbus RTU)
※1: Current measurement and connection examples
Connect 250Ω shunt resistance and set analog input type 0-20mA (shunt) / 4-20mA (shunt).
It is available to measure 0-20mA / 4-20mA current.
※2: At room temperature (23℃± 5℃)
RTD Cu50Ω (-200≤T≤200): (±0.1% F.S. or ±1.5℃, select the higher one) ±1-digit
RTD DPt50Ω (-200≤T≤500): (±0.1% F.S. or ±1.5℃, select the higher one) ±1-digit
Thermocouple R, S, C, G type (0≤T≤100): (±0.1% F.S. or ±4.0℃, select the higher one) ±1-digit
Thermocouple U, T type (-100≤T≤400): (±0.1% F.S. or ±2.0℃, select the higher one) ±1 digit
Thermocouple B type, below 400℃: There is no accuracy standards.
All thermocouples, below -100℃: (±0.3% F.S. or ±4.0℃, select the higher one) ±1-digit
Out of room temperature range
RTD Cu50Ω (-200≤T≤200): (±0.2% F.S. or ±3.0℃, select the higher one) ±1-digit
RTD DPt50Ω (-200≤T≤500): (±0.2% F.S. or ±3.0℃, select the higher one) ±1-digit
※3: Input/Output is different by option. Refer to ‘ Ordering Information’.
※4: For supplying power for transmitter, it is recommened to use shield cable to reduce noise.
※5: RS422/485, ethernet, USB device communication outputs are not used at the same time.
※If sensor input line is longer, it is recommended to use shield cable to reduce noise.
5
4
3
2
1
AEP-E-0180C

4) Memory Management [Menu → Memory Info. → Memory Management]
It manages internal/external memory. You can check memory usage and move and copy data files.
No Item Descriptions
1Internal Memory Displays each memory usage.
Touch ‘Clear’ to initial the memory.
2 SD Memory
3 USB Memory
4 Move/Copy
Moves/Copies les of internal memory to SD/USB memory.
- Move: Moves the le to external memory and deletes the existing le at internal memory.
- Copy: Moves the le to external memory and maintains the existing le at internal memory.
- Delete: Deletes the le.
- Move All: Moves all les to external memory and deletes the existing all les at internal memory.
- Copy All: Moves all les to external memory and maintains the existing all les at internal memory.
- Delete All: Deletes all les.
5 Storage Select the memory to save the data.
1
4
5
2
3
Status Display Part
1 2 3 4 5 6 7 8
Section Item Description
1
Menu Displays menu.
Esc Moves from menu to current screen.
Home Moves to main screen.
2Group
Displays currently displayed group name.
Touch the icon and select the group. You can set the group name and the set
group name is displayed.
3Graph
Select the displayed graph at the current screen.
Select one among bar graph, vertical/horizontal trend graph, divided vertical/
horizontal trend graph, vertical/horizontal mixed graph, digital group/all.
4
Lock Displays at standard user mode.
(activated log-in function or log off status)
Lock Setting Displays at administor mode.
(activated log-in function and log-in as administor mode)
Unlock Displays at unlock.
(inactivated log-in function)
No Alarm Displays at no alarm.
Alarm Displays when alarm occurs.
5
Internal Memory
Record
Displays when displaying measurement value and no recording it at internal
memory.
Internal Memory
No Record Displays usage details of data recording space.
6
Data Record Space Displays usage details of data recording space.
Alarm Record Space Displays empty space of alarm data memory.
Event Record Space Displays empty space of event data memory.
7
USB Memory
No Connection Displays when USB memory is not connected.
USB Memory No Save
(gray) Displays when internal memory data does not save at USB memory.
USB Memory Save
(yellow) Displays when internal memory data saves at USB memory.
SD Card
No Connection Displays when SD card is not connected.
SD Card No Save
(gray) Displays when internal memory data does not save at SD card.
SD Card Save
(yellow) Displays when internal memory data saves at SD card.
8Date/Time
Displays date and time.
If summer time is set, "(s)" marks in front of time.
Menu
3) File [Menu → System Info. → File]
It manages parameter setting files which are saved at KRN1000 memory, resets parameters.
No Item Descriptions
1Parameter
Setting File Displays parameter setting le name.
2Internal Memory
Save the set parameter information at the dedicated memory or open it.
3 SD Memory
4 USB Memory
5 Reset Parameters Reset parameter settings as factory default.
6Screen Simulation
(Demo)
Execute simulation the set parameters.
Touch ‘Start’ and re-boot the unit and simulation mode starts.
Touch ‘Stop’ to exit simulation mode and re-boot the unit.
1
4
2
5
3
6
※For more information about menu, refer to KRN1000 user manual.
Major Products
Photoelectric Sensors Temperature Controllers
Fiber Optic Sensors Temperature/Humidity Transducers
Door Sensors SSRs/Power Controllers
Door Side Sensors Counters
Area Sensors Timers
Proximity Sensors Panel Meters
Pressure Sensors Tachometer/Pulse(Rate) Meters
Rotary Encoders Display Units
Connectors/Sockets Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System(Fiber, CO₂, Nd:YAG)
Laser Welding/Cutting System
Recorders Thyristor Power Controllers
Indicators Pressure Transmitters
Converters Temperature Transmitters
Controllers
It sets initial setting and option of KRN1000.
2) Device [Menu → System Info. → Device]
No Item Descriptions
1 Device Name Set KRN1000 device name.
It supports English capital/small letter, sign and number up to 16 characters.
2 Language Set KRN1000 display langauge.
It supports Korean, English and Chinese.
3 PWR ON Record
Set record status when supplying power or re-supplying power at power failure.
- Hold: It maintains record status (recording/stop) of before power OFF.
- Record: It records when power is ON.
- Stop: It does not record regardless when power is ON.
4 Sampling
Set internal sampling period of measurement value.
Setting range(varied by number of input channel connections)
- Below 4CHs: 25, 125, 250ms
- The others: 125, 250ms
5Log Record
Speed
Set log speed for recording measurement value at system memory.
Setting range: 1 to 3600 sec
E.g.) When setting as 3 sec, it records present value and the value after 3 sec.
6 Backlight Set display backlight level.
Setting range: Min., Standard, Max.
7 Screen Save
For saving LCD life cycle and power, screen can automatically turn OFF.
Even though during screen save status, it maintains recording. Touch the screen and it turn ON the screen.
Setting range: 0 to 360 min (0: disable screen save)
8 Alarm Sound Set alarm sound volume.
Setting range: OFF, Min., Standard, Max.
9 Touch Sound Set touch sound volume when toucing the menu or button of screen.
Setting range: OFF, Min., Standard, Max.
1 4
25
36
8 9
7
Major Menu
1) Input/Display [Menu → Input CH Info. → Input/Display]
1
4
2
5
3
6
8
9
10
7
No Item Descriptions
1 Channel Moves channel. Touch 'CH1' or to change the channel.
2 Copy Copies the other channels parameters of the same group. Select the channel to be copy.
3Input Type Set the input type. Input types are total 27: thermocouple, RTD, voltage, current (shunt).
4Low-Limit Graph Scale/
Low-Limit Input
In case of temperature sensor input, set the low-limit graph scale value within the input range.
Setting range: Min. value of input range to high-limit graph scale value-F.S. 5%
E.g.) In case of TC-K input, -200.0 to 1350.0℃of input range, and setting range is -200.0 to 1272.5℃.
(-F.S.=77.5)
In case of analog input, it displays low-limit input value.
5
High-Limit Graph Scale/
High-Limit Input
In case of temperature sensor input, set the high-limit graph scale value within the input range.
Setting range: Low-limit graph scale value+F.S. 5% to Max. value of input range
E.g.) In case of TC-K input, -200.0 to 1350.0℃of input range, and setting range is -122.5 to 1350℃.
(+F.S.=77.5)
In case of analog input, it displays high-limit input value.
6 Point - Temperature sensor input: 0, 0.0 (set the decimal point for the measurement value)
- Analog input: 0, 0.0, 0.00, 0.000, 0.0000 (set the decimal point position for the scale value)
7 Tag Name Set the channel name.
8 Low-Limit Scale Set the desired display value based on the measurement value.
It is activated only for analog (voltage, current (shunt)) input type.
9 High-Limit Scale
10 Display Unit - Temperature senosr input: Temperature units, ℃, ℉, ˚K are available.
- Analog input: 72 display units are available. When not using unit, select blank.
It sets input type of each channel of KRN1000.
Display History
File History
Group Setting
Touch Calibration
Input CH Info. Input/Display
Input Option
Alarm
User Unit
Option Info. Alarm Output
Digital Input
RS422/485
Ethernet/USB
Status Alarm List
Event List
AO/DI Status
Screen Capture
Log OFF/Power OFF
Memory Info. Memory Management
Internal Memory
System Info. Date/Time
Reservation
Device
Log In
File
System Info.
http://www.autonics.com
HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, South Korea, 48002
OVERSEAS SALES:
#402-303, Bucheon Techno Park, 655, Pyeongcheon-ro, Wonmi-gu, Bucheon,
Gyeonggi-do, South Korea, 14502
TEL: [phone] / FAX: [phone]
E-mail: [email protected]
AEP-E-0180C