AuVerte GK10 Series User manual

Version 1.02 28 May, 2020 AuVerte AG Rothusmatt 14, CH-6300 Zug, Switzerland www.AuVerte.com
GK10x Optical Door/Window Sensor
Benefits
Optical sensing of a barrier, such as a door or window
Wireless communication to room automation equipment
Simple to use –simple to maintain
No drilling of doors and frames for installation
True IPv6 IoT connectivity to all devices
Low cost
Ten-year warranty
Powered by CR2450 lithium coin cell battery lasting 5 years
Designed for end-of-life product recoverability
Models
Black and white housing colors
The GK10x optical sensor from AuVerte is part of a modern room automation solution. When used for a room entry door, this sensor is a key element to
determine the occupancy status of an enclosed space in combination with one or multiple motion sensors. When used to monitor windows and balcony doors,
this sensor can curtail HVAC energy during periods when the room is exposed to the outside environment. Battery powered and utilizing wireless RF
communication, the GK10x is simple to install and to maintain.
C5xx Ondur Thermostat
FS10x PIR Motion Sensor
GK104 Aux. Temperature/Humidity Sensor
Model：GK100

GK10x Optical Sensor Cut Sheet
Page 2 © AuVerte AG
Specifications
Sensors
Optical Sensor
Two optical reflection sensors, sensing
distance 3-10mm depending on reflexivity
of detected surface
Sampling speed
Dynamic, less than 500 milli seconds
Radio
Standard
IEEE 802.15.4
Frequency band
ISM 2.4 GHz
Interference
immunity
DSSS (Direct sequence spread spectrum)
Data rate
250 kbps
Antenna
Build-in
Indoor range
Up to 50 m (150 ft)
Transmit power
+3 dBm
Receiver sensitivity
-95 dBm
Channels
16 (11 to 26, default 25)
Protocol
AuVerte mesh
IPv6 over 802.15.4 with forward error
correction (FEC-ECC) via proxy
Software
Encryption
AES128
Routing
UDP over AuVerte Rf mesh and through
an IPv6 proxy device
Cyber security
Packet authentication, configurable
encryption keys with no backdoors
Device
Power
CR2450 3V/620mAh coin-cell (not included)
Approved battery vendors:
•Panasonic
•Mitsubishi
•Murata
Battery life
5 years
Mounting
Surface mount, double-sided adhesive tape.
Environmental and Physical Specification
Dimensions
49mm x 27.5mm x 12mm
Weight
0.018 kg, 0.42oz (incl. battery)
0.012 kg, 0.63oz (without battery)
Operating
temperature
10 °C to 40 °C (50 °F to 104 °F)
Storage temperature
-20 °C to 70 °C (--4 °F to 158 °F)
Operating humidity
10 % to 95 %RH, non-condensing
Storage humidity
5 % to 90 %RH, non-condensing
Electromagnetic
emissions
FCC Part 15 Class A
EN 62311 (EMR)
ETSI EN 300 328 (2.5GHz ISM Band)
ETSI EN 301489 (EMC)
Safety approvals
EN 60950
Environmental
RoHS
Cleaning
Mild cleaning liquid, soft towel
Recycling
6.5g ABS, 5.5g electronics, 6.0g battery
Ordering Information
Part numbers
003003.GK101
Package content
6 GK101 sensors
Color Options
◼White
◼Black
Options
None
AuVerte AG
Rothusmatt 14
CH-6300 Zug
Switzerland
www.auverte.com

FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.