Output protocols Wiegand or RS485
Power requirement 8VDC to 16VDC (nominal operating voltage 12VDC)
Current
consumption
60mA (Average)
160mA (Peak)
Read range 20mm to 40mm (0.8” to 1.6”) at12VDC
depends on the type ofcard used
Operating
temperature -25°Cto +65°C(-13°Fto +149°F)
Relative humidity 90% max, operating non-condensing
Reader dimensions AU Perplex plate (BT510)
116mm(L) x 84mm(W) x 26mm(D) (4.57” x 3.31” x 1.02”)
UK Perplex plate (BT511)
116mm(L) x 80mm(W) x 26mm(D) (4.57” x 3.15” x 1.02”)
Status LED Green & Red
Audible tone Internal and external buzzer control
Colour finish Charcoal
IP rating IP65
Wiring diagram
Note:
•Ashielded cable is recommended to beused. The shield is connected to controller 0Vreference
•Maximum wiegand data cable length: 150 meters (500 feet)
•Buzzer and LEDare low activated.
•RS485 lines areonly for optional use.
•Insulate all un-used wires (do not terminate).
Regulatory Information
C-Tick: This device is C-Tick complied.
CE: The device has passed all relevant tests and obtained CE approval.
FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device
may not cause interference and 2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this
equipment.
Warranty
Unless specified otherwise, the Company warrants tothe Customer that’ BQT Solutions Branded
Products’ (excluding third party products and software)are covered by a return tobase warranty on
defects in materials and workmanship affecting normal use fora period of the Warranty offered under
the Standard Terms and Conditions of Sale from BQT invoice date (‘Standard Warranty’)
This standard warranty does notcover damage, fault, failure or malfunction due toexternal causes
including; accident, misuse, problems with electrical power, servicing not authorised by the Company,
usage and/or storage and/or installation not inaccordance with Product instructions, failure toperform
required preventative maintenance, normal wear and tear, act ofGod, fire, flood, war, any violent or
similar occurrence; any attempt by any person other than Company personnel orany person authorised
by the Company to repair orsupport the Products and problems caused by use of parts and
components not supplied by the Company. The standard warranty does not cover any items that are in
one or more of the following categories: software; external devices; accessories or parts added to the
product after the product hasbeen shipped from BQT Solutions.
During the warranty, period beginning on the invoice date, the Company will repair or replace faulty
products (at its absolute discretion) returned to its’ factory. The Customer must prepay shipping and
transportation costs and insure the shipment oraccept the risk of loss ordamage during such
transportation.
The Customer shall be solely responsible for determining suitability for use and the Company will, in no
event, beliable in this respect. This standard warranty is given in place of all warranties, conditions,
terms, undertakings and obligations implied by statute, common law, trade usage, and course of
dealing or otherwise including warranties or conditions ofmerchantability, fitness for purpose,
satisfactory quality and / orcompliance with description, all of which are hereby excluded tothe fullest
extent permitted by law.
BT510
INSTALLATION GUIDE
Rev 002
Specifications
© 2015 BQT Solutions (Australia) Pty Limited. All rights reserved.
BQT Solutions (Australia) Pty Limited will not be liable for any direct, indirect, incidental or
consequential loss or damage in any way related to this product. BQT Solutions (Australia)
Pty Limited reserves the right to upgrade or change this product or instruction manual
without prior notice. BQT Solutions (Australia) Pty Limited assumes no liability for damages
incurred directly or indirectly from errors, omissions or discrepancies between the product
and the manual.
The product is designed by BQT Solutions (Australia) Pty Limited.
For more information and contact details please visit,
www.bqtsolutions.com
