FlexiForce 9700V12 User manual

Keypad/Card reader
manual
www.flexiforce.com
FF-MANUAL SuperClick
9700V12 - 9700V24
9700CARD
Keypad/Card reader
© All rights reserved. FlexiForce®, 2012

forceR600
manual
www.flexiforce.com page 2
Keypad/Card reader
manual
www.flexiforce.com page 2
1. description of LED and buzzer indicators:
Description Red LED Green LED Buzzer
Normal mode ON
Program mode Flash
Under program mode ON
Non registered card ON Di (long)
Card only mode ON with same dura-
tion of door open Di Di (short)
Card and password
mode (after card
swipe, waiting for
password)
Red and green LED blink alternatively
Card and password
mode
Flash for each 0,5
second
Password only mode Flash for each second
Button tone Di (short)
Successful setup Di Di (short)
Faulty setup Di (long)
Invalid command Di (long)
Alarm mode Di Di Di (continuously)
Programming guide:
1. Get into programming mode:
Press ####: Red LED is OFF, Green LED is ON. Then press 123456#
Now Red should be off and Green should flash. If not: try again (provided the program password was not
modified before). Default program password is 123456.
2. Changing the program password:
Press 0 “new password” # “new password” # (new password must have 6 digits). Please beware this ac-
tion is only possible when in program mode (see step 1)
3. Adding cards with automatic number assignment
Press 1 - swipe card - # (only possible with unregistered cards!)
The 9700V12/24 will assign an individual card number to each registered card. If this is a new installation
the numbering of cards will start with 0001, 0002 etc. If this 9700V12/24 already has card programmed to it,
the next card will be assigned the next available number.
If the card you swipe is an already registered one you’ll hear a long warning signal (Di). You can still con-
tinue programming other cards.
4. Adding cards with specific number assignment
Press 2 - swipe card - “card number” # (repeat this step until the last card) #
If the card you swipe is an already registered one you’ll hear a long warning signal (Di). You can still con-
tinue programming other cards.
If the number you enter is already in use you’ll hear a long warning signal (Di). You can still continue by en-
tering another card number.

forceR600
manual
www.flexiforce.com page 3
Keypad/Card reader
manual
www.flexiforce.com page 3
5. Deleting registered cards
Press 30 - swipe card - # the swiped card is now deleted
Press 31 - “card number” # the card with that number is now deleted
Press 32 - 9999 - # all cards are now deleted
6. Setting the access mode
Press 40 # card or personal code to access (default)
Press 41 # card AND personal code to access
Press 42 # personal code only
8. Program personal access code
Press 6 “new code” # “new code” # must be a 6 digit code
Press 6 # # personal access code is deactivated
9. Exiting program mode
Press *
10. Changing the card password (only needed when in card AND personal code mode)
The 9700V12/24 recognizes a different pass code for the ‘card AND personal code’ mode. In other words:
this code is not the same as the regular pass code.
Press * (green LED will go ON) - swipe card - “old password (default is 888888)” (red and green LED flash
alternating) “new password” # “new password” #
Green LED will be OFF and you’ll hear two short (Di Di) signals to confirm. In case of failure to program
you’ll hear a long (Di) signal. Try again.
11. Back to factory settings
Cut off power. Put jumper JP1 in 2-3 position. Re-connect to power. After you hear two short (Di Di) signals,
put jumper JP1 in position 1-2.
Examples of programming:
1. Change program password to 789000:
a. enter program mode by pressing #### 123456 # (green LED flashes)
b. press 0 789000 # 789000 #
c. press * (to exit program mode)
2. Add new cards in a continuous way:
a. enter program mode: #### 123456 # (green LED flashes)

forceR600
manual
www.flexiforce.com page 4
Keypad/Card reader
manual
www.flexiforce.com page 4
b. press 1 - swipe all cards you want to add -
c. press * (to exit program mode)
d. all added cards are ready for use.
3. Add two new cards numbered 0088 and 0099:
a. enter program mode: #### 123456 # (green LED flashes)
b. press 2 - swipe card - 0088 # swipe second card 0099 ##
c. press * (to exit program mode)
4. Delete cards numbered 0088 and 0099:
a. enter program mode: #### 123456 # (green LED flashes)
b. press 31 0088 # 0099 ##
c. press * (to exit program mode)
5. Change access mode to Card Only:
a. enter program mode: #### 123456 # (green LED flashes)
b. press 40 #
c. press * (to exit program mode)
6. Change access code to 147258:
a. enter program mode: #### 123456 # (green LED flashes)
b. press 6 147258 # 147258 #
c. press * (to exit program mode)
Wiring Diagram
Green GND push/exit button
Green OPEN
Blue NO
dry output contactWhite COM
Yellow NC
Black GND power supply
Red +VCC