Avallon ABR151BLSS User manual

USER’S GUIDE
Installation, Operation, and Maintenance for your product.
Built-In Beverage Refrigerator
Model –ABR151BLSS
www.avallon.com
V2.1-03182020

ii
Important Safety Information
Improper handling can cause serious damage to the Avallon beverage refrigerator and/or injury to the user.
This beverage refrigerator is designed for domestic indoor use only. Do not use the unit for industrial or
commercial use. Any other use may invalidate the warranty. Please review the rating label located on the
rear panel of the unit for electrical and other technical data related to this unit. The unit must be used in a
properly grounded wall outlet. Please read and follow the safety information listed below to reduce the
risk of fire, electric shock, or injury.
ELECTRICAL SAFETY
•Do not exceed the power outlet ratings.
•It is recommended the beverage refrigerator be connected on its own circuit.
•The unit must be installed in accordance with state and local electrical codes.
•A standard electrical supply (115 V, 60Hz), that is properly grounded in accordance with the National Electrical
Code and local codes and ordinances is required.
•Use outlets that cannot be turned off by a switch or pull chain.
•Always turn the unit off and unplug it from the outlet when cleaning.
•Unplug the unit if it is not going to be used for an extended period of time.
•Do not operate the unit with a power plug missing the ground plug, a damaged cord, or a loose socket.
•Be sure the beverage refrigerator is properly grounded.
•Avoid installation in high humidity environments such as bathrooms and non-acclimatized basements. Excess
moisture may create condensation on the door and impact the performance of the refrigerator.
•Never plug or unplug the unit with wet hands.
•Do not bypass, cut, or remove the grounding plug.
•Do not use extension cords or power strips with this unit. You may need to contact your electrician if it is
necessary to use a longer cord or if you do not have a grounded outlet. Do not modify the power cord’s length
or share the outlet with other appliances.
•Do not start or stop the unit by switching the circuit’s power on and off.
•If the power cord is damaged, it must be replaced by the manufacturer or a qualified technician.
•Never repair the unit while it is plugged in.
•Immediately unplug the unit if it makes strange sounds, emits smells, or smoke comes out of it, and contact
customer service.
•Do not remove any part of the casing unless instructed to do so by an authorized technician.
•You should never attempt to repair the unit yourself. Contact customer service for service options if the unit
needs service.

iii
Note: Flammable Refrigerant Used! When handling, moving, and using the refrigerator, make sure to
avoid either damaging the refrigerant tubing, or increasing the risk of a leak.
Disposal: This appliance may not be treated as regular household waste, it should be taken to the
appropriate waste collection.
point for recycling of electrical components. For information on local waste collection points, contact your
local waste
removal agency or government office.
GENERAL SAFETY
•To prevent injuries, use at least two people to move and install the beverage refrigerator.
•Install the beverage refrigerator in a well-ventilated area where the ambient temperature is above 50° F and
below 90° F.
•The temperature range for this refrigerator is optimized for beverage storage. Perishable food items may
require a different storage environment.
•Do not place hot or warm items into the refrigerator before they cool down to room temperature.
•This unit is designed to be installed indoors, and protected from rain, sleet, snow, and / or moisture.
•This unit is not intended to be used by children.
•Children should be supervised to ensure that they do not play with this product.
•Never allow children to crawl inside the refrigerator. If you are disposing of the unit, remove the door.
•Do not use this appliance near flammable gas or combustibles such as gasoline, benzene, or thinner.
•Do not store explosive substances such as aerosol cans with flammable propellant in this appliance.
•Do not place the unit near heat sources such as ovens, grills, or direct sunlight.
•Only use in an upright position on a flat, level surface and provide proper ventilation.
•Do not pinch or kink the power supply line between the unit and cabinet.
•Do not leave any cleaning solutions in the unit.
•Do not use solvent-based cleaning agents or abrasive solutions to clean the unit as they may damage the
interior and exterior.
•Do not place any other appliances on top of the unit.
•Do not turn the unit upside down, on its side, or at an angle off level.
•If your model of beverage refrigerator is equipped with a lock, keep the keys away from children.
•Do not move the unit without emptying the contents and securing the door in a closed position.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory, or
mental capabilities unless they are given supervision or instruction by a person responsible for their safety.
•This appliance is meant for use in the household or similar settings.
•Keep all ventilation openings clear of obstruction.
•Do not use mechanical devices or other means to accelerate the defrosting process.
•Do not damage the refrigerant circuit.
•Do not use other appliances inside the refrigerator unless recommended by the manufacturer.
•If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly
qualified individual.

iv
Table of Contents
Important Safety Information..................................................................................................................................................ii
Table of Contents....................................................................................................................................................................iv
Introduction ............................................................................................................................................................................ 1
Parts Identification.................................................................................................................................................................. 2
Full View.................................................................................................................................................................................. 2
Empty View ............................................................................................................................................................................. 2
Back View................................................................................................................................................................................ 3
Installing Your Beverage Refrigerator..................................................................................................................................... 4
TYPES OF INSTALLATION:........................................................................................................................................................ 4
Installation Clearance Requirements:..................................................................................................................................... 5
LEVELING:................................................................................................................................................................................ 5
RECOMMENDED GROUNDING METHOD:............................................................................................................................... 6
Installing Your Door Handle and Shelves ................................................................................................................................ 6
INSTALLING THE DOOR HANDLE:............................................................................................................................................ 6
INSTALLING THE SHELVES: ...................................................................................................................................................... 7
REMOVING THE SHELVES:....................................................................................................................................................... 7
Reversing Your Door Swing..................................................................................................................................................... 8
REVERSING THE DOOR:........................................................................................................................................................... 8
Operation................................................................................................................................................................................ 9
INSTALLATION CHECK-LIST BEFORE OPERATION:................................................................................................................... 9
USING YOUR CONTROL PANEL:............................................................................................................................................... 9
Internal Light......................................................................................................................................................................... 10
Defrosting ............................................................................................................................................................................. 11
Normal Sounds...................................................................................................................................................................... 11
Temperature Alarm............................................................................................................................................................... 11
Door Ajar Alarm .................................................................................................................................................................... 11
Cleaning and Maintenance ................................................................................................................................................... 12
INTERIOR CLEANING: ............................................................................................................................................................ 12
EXTERIOR CLEANING:............................................................................................................................................................ 12
Preparing Your Beverage Refrigerator for Storage............................................................................................................... 12
Troubleshooting .................................................................................................................................................................... 13
Specifications ........................................................................................................................................................................ 15
Avallon Product Warranty .................................................................................................................................................... 16

v
First Time Operating Instructions:
Before use, make sure all packaging labels and materials are removed from the unit. Be sure to keep
track of all included parts and pieces before discarding packaging materials. It is advised that you keep
the original box and packaging materials in case you need to move or ship the appliance in the future.
Allow the unit to stand for at least 24 hours before you use it; this allows the cooling components time to
settle from transit. The instruction manual should be read before use.
This owner’s manual is provided for reference use only. Specifications may change without prior notice.
Refer to the product label on the back of your beverage refrigerator for the latest technical information.

Introduction
Thank you for purchasing your Avallon beverage refrigerator. Avallon is dedicated to developing products
that will enhance your lifestyle with superior quality and distinctive features. Please visit www.avallon.com
for more information on your product and other Avallon products.
This manual contains important information regarding the proper installation, use, and maintenance of your
beverage refrigerator. Following this manual will ensure that your product will work at its peak performance
and efficiency.
Please save the original product packaging in case you need to safely transport your beverage refrigerator.
For Your Records:
Please write down the model number and serial number below for future reference. Both numbers are
located on the rating label on the back of your unit and are needed to obtain warranty service. You may
also want to staple your receipt to this manual as it is the proof of your purchase, and is also needed for
service under your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer service:
• If you received a damaged product, immediately contact the retailer or dealer that sold you the
product.
•Read and follow this instruction manual carefully to help you install, use, and maintain your beverage
refrigerator.
• Read the troubleshooting section of this manual as it will help you diagnose and solve common
issues.
•Visit us on the web at http://www.avallon.com to download product guides, additional
troubleshooting resources, and up-to-date information.
•If you need warranty service, our friendly customer service representatives are available via email at
[email protected].

2
Parts Identification
Full View
Empty View

3
Back View
Carbon Filter
A built-in carbon filter protects your beverages by acting as a natural barrier against harmful odors.
Internal Fan
This is an air-cooled unit equipped with an internal fan that maintains a consistent internal temperature.
Note: The carbon filter should be replaced every 3-6 months depending on the unit’s exposure level to
odor. If the unit is placed in a kitchen, regular replacement every three (3) months is ideal.
Tip: Gather the model and serial number from the product label and write them down before installing the
beverage refrigerator.

4
Installing Your Beverage Refrigerator
The beverage refrigerator should be installed in accordance with local electrical code requirements. It
should also be placed in a location that is strong enough to support its total weight, keeping in mind that it
will weigh substantially more when fully loaded than when empty.
Before you plug the beverage refrigerator into a power supply, be sure to let it stand upright for at least 24
hours to allow the compressor’s oils to settle.
TYPES OF INSTALLATION:
This beverage refrigerator has been designed for freestanding or built-in installation. In every case, there
must be adequate ventilation and access for service.
Freestanding Installation
A freestanding installation will allow you to install the beverage refrigerator in almost any place you desire.
You must follow the stated instructions for electrical requirements and leveling the beverage refrigerator.
Built-in Installation
A recessed installation will allow you to install the beverage refrigerator under a counter or in a kitchen
cabinet provided the clearance space requirements around the beverage refrigerator are followed. It is
necessary to allow adequate ventilation space around the unit (make sure there is at least some
ventilation room for the back of the unit). The following additional items must be observed:
1. Place the beverage refrigerator in front of the installation location.
2. Adjust the feet and place the unit flat on the floor or on a platform depending on your installation
requirements.
3. If the electrical outlet for the beverage refrigerator is behind the cabinet, plug in the beverage
refrigerator.
4. Push the beverage refrigerator into position.
5.
Warning: Use two or more people to move and install the beverage refrigerator. Failure to do so can result
in back or other injury. Carefully remove the packaging materials. Remove any shipping tape and glue from
your beverage refrigerator before using. Do not use sharp instruments, rubbing alcohol, flammable fluids,
or abrasive cleaners to remove tape or glue. These products can damage the surface of your beverage
refrigerator.
Important: Do not remove any safety, warning, or product information labels from your beverage
refrigerator.
Warning: DO NOT install the beverage refrigerator behind a closed cabinet door.

5
Installation Clearance Requirements:
When installing the beverage refrigerator under a counter, follow the recommended spacing dimensions shown.
•To ensure proper service access and ventilation, allow between 1 - 2 inches of clearance at the back as
shown in the diagram.
•The installation should allow the unit to be pulled forward for servicing, if necessary.
•A standard electrical supply (115 VAC only, 60 Hz), properly grounded in accordance with National
Electrical Code and local codes and ordinances, is required.
LEVELING:
The beverage refrigerator should be installed on a firm and level surface that will be able to support the
entire weight of a fully loaded unit. It is important for the beverage refrigerator to be leveled in order to
work properly. It can be raised or lowered by rotating the plastic sheaths around each of the feet on the
bottom of the machine. If you find that the surface is not level, rotate the feet until the beverage
refrigerator becomes level. You may need to make several adjustments to level it. We recommend using a
carpenter’s level to check the machine. Turn the leveling feet clockwise to lower that side of the
refrigerator. Turn the leveling feet counterclockwise to raise that side of the refrigerator.
Important: Once you are ready to install the unit in a cabinet or directly on the floor, you must adjust the
feet to level the beverage refrigerator.

6
RECOMMENDED GROUNDING METHOD:
For your personal safety, this appliance must be grounded. It is equipped with a power supply cord having a
3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-
pronged wall socket, and grounded in accordance with the National Electrical Code and local codes and
ordinances. If a mating wall socket is not available, it is the personal responsibility of the customer to have a
properly grounded, 3-prong wall receptacle installed by a qualified electrician.
Before you move your beverage refrigerator into its final location, it is important to make sure you have the
proper electrical connection. A standard electrical supply (115 V, 60Hz), properly grounded in accordance
with the National Electrical Code and local codes and ordinances, is required. It is recommended that a
separate circuit, serving only your beverage refrigerator, be provided. Use receptacles that cannot be
turned off by a switch or pull chain.
The fuse (or circuit breaker) size should be 15 Amps.
Installing Your Door Handle and Shelves
INSTALLING THE DOOR HANDLE:
1. Open the door and carefully pull the door gasket around the area where the handle is to be installed.
2. Insert each Phillips head screw through the gasket side of the door until the screw passes through the
door.
3. Align the handle with the screws and tighten using a Phillips head screwdriver until the handle is flush
against the door frame.
4. Carefully press the door gasket into its original position.
Electrical Shock Hazard!
•Plug into a grounded 3-prong outlet.
•Never remove the grounding prong from the plug.
•Never use an adapter to bypass the grounding prong.
•DO NOT use an extension cord.
•Failure to follow these instructions can result in fire, electrical shock, or personal injury.
Caution: Do not over-tighten the screws as this may cause damage to the handle or to the stainless steel
door.

7
INSTALLING THE SHELVES:
1. Open the door completely.
2. Ensure that the metal guide posts are attached to the rear of the shelf.
3. Tilt the shelf 45° counterclockwise. The metal guide post on your left side should rest on the shelf track.
4. Gently push the shelf back towards the rear of the unit until the right side metal guide post meets the
vertical indentation in the plastic interior cabinet.
5. Gently set the right side of the shelf down on the shelf track. The shelf should move forwards and
backwards smoothly.
REMOVING THE SHELVES:
1. Open the door completely.
2. Make sure the shelf is pushed back completely.
3. Lift either the left or right side of the shelf to create a 45° angle from its original position. Make sure not
to lift either side of the shelf too hard as it may come in contact with the inner wall mount.
4. Pull the shelf outward until it is removed from the inner compartment. You may encounter some
resistance from the shelf guard rail.
Tip: To prevent damaging the door gasket, make sure to open the door fully before pulling the shelves out
of their track.
Note: The refrigerator may experience decreased cooling efficiency if air flow is restricted due to a fully
loaded cabinet.

8
Reversing Your Door Swing
REVERSING THE DOOR:
A. Open the door to a 90 degree angle, take out the 2 screws from the lower door axis (1), remove the
door (2) and the axis plate from the door.
B. Take out the 3 hinge screws from the top right hinge (3) and remove it.
C. Unscrew the 2 screws at the bottom of the door and remove the door switch (4), then install the door
switch at the top of the door.
D. Remove the decorative covers (6) from the top left of the cabinet and install the new top hinge (5) at
the tip of the cabinet with 3 screws.
E. Install the door once correctly aligned.
WARNING: Disconnect power before removing door.
Note: Door reversal operation requires at least two persons.

9
Operation
INSTALLATION CHECK-LIST BEFORE OPERATION:
1. Have all packing materials and tape been removed from the interior and exterior of the beverage
refrigerator?
2. Have the installation instructions been followed, including connecting the machine to electricity?
3. Has proper grounding been installed for the beverage refrigerator?
4. Has the machine been leveled?
5. Is the beverage refrigerator in a site where the ambient temperature is between 50° F and 90° F all year
round?
6. Is there a clearance of at least 1”to 2” at the rear for proper air circulation?
USING YOUR CONTROL PANEL:
This beverage refrigerator has a temperature range from 34° F to 50° F.
Power Button
Press and hold this button down for three seconds to power your unit on. Once pressed, the “Run”
indicator light will illuminate to indicate the unit is on and running. Press and hold this button for three
seconds again and the unit will power off and the “Run” Indicator light will turn off.
Increase Temperature
Press this button to increase the temperature by one (1) degree increments. 50° F is the highest
available temperature on this unit.
Decrease Temperature
Press this button to decrease the temperature by one (1) degree increments. 34° F is the lowest
available temperature on this unit.
Interior Light
Press this button to cycle through the different internal light settings. There are four light settings:
Constant Blue, Constant White, Automatic Blue, and Automatic White. Press this button to choose the
next option in the progression, eventually cycling back to the original setting. The lights will fade out of
the previous setting and into the next setting in the cycle each time you press this button. Press and hold
this button for three seconds to turn the lights completely off or to turn them back on. Open and close
the door to check the internal light color and whether the lights stay on with the door closed (Constant
Mode) or illuminate only when the door is open (Automatic Mode). Please refer to the “Internal Light”
section on the next page for further detail.

10
Warning: Allow at least 24 hours for your beverage refrigerator to run before storing your beverages and to
allow the temperature to acclimate. Whether your beverage refrigerator can reach the actual set
temperature depends on the ambient environmental conditions.
Internal Light
This refrigerator is equipped with top and side internal lights that can be set to a blue or white color.
Because the unit comes with a glass door, the inside will be seen whether the door is open or closed. You
can choose to display each color of light in two different modes: Constant Mode and Automatic Mode.
Constant Mode
The internal lights will stay constantly illuminated whether the door is open or closed.
Automatic Mode
The internal lights will illuminate each time the door is opened and fade off once the door is closed. This
feature is triggered by a sensor located on the front vent. This sensor allows the refrigerator to recognize
when the door is open or closed.
With each press of the light button, the unit will progress through the cycle of light settings seen below.
Holding the light button for three seconds will turn the lights completely off or back on. If you power the
lights off they will remain off, even when the door is open. Hold the light button for three seconds again to
turn the lights back on.
Note: Pressing and holding the increase and decrease temperature buttons at the same time will switch the
temperature display from °F to °C.
Tip: If you powered the unit off, please wait at least five (5) minutes before powering it back on.
Note: We run test every unit that we produce in our factory. Because of this, your model may default to
any of the above settings out of the box. Simply cycle through the progression of settings until you reach
your desired light setting. The lights will return to the Constant Blue setting after the Automatic White
setting, thus starting back at the beginning of the progression.
Tip: Close the door to determine if the light is currently in Constant Mode or Automatic Mode. In Constant
Mode the lights will remain on, and in Automatic Mode the lights will fade off once the door is closed.

11
Defrosting
The refrigerator will automatically defrost under most temperature settings and ambient conditions. However,
on colder settings, some frost may build up. Additionally, under more humid ambient conditions, more frost
may build up. Keep the door closed as much as possible and avoid opening the door unnecessarily to minimize
frost build-up.
If frost is preventing the door from closing properly, you may need to power the unit off until the frost melts.
Use a soft absorbent towel to dry the unit.
Normal Sounds
Your new beverage refrigerator may make sounds that are not familiar to you. Most of the new sounds are
normal. Hard surfaces like the floor or walls can make the sounds seem louder than they actually are. The
following describes the kinds of sounds that might be new to you and what may be making them.
•Rattling noises may come from the flow of the refrigerant or the water line.
•Items stored on top of the beverage refrigerator can also make noises.
•The high efficiency compressor may make a pulsating or high-pitched sound.
•The internal fan will run frequently to create a consistent internal temperature environment.
•Water running from the evaporator to the water bin may make a splashing sound.
•As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your beverage
refrigerator.
•You may hear air being forced over the condenser by the condenser fan.
Temperature Alarm
If the interior temperature is higher than 73°F (23°C), “HI” is shown on the temperature
control panel and the temperature alarm will sound continuously after one hour.
This indicates that the inner temperature is too high. If the inner temperature is lower
than 25°F (-4°C), “LO” is shown on the temperature display panel and the temperature
alarm will sound continuously after one hour. If one of these situations occurs, please
reference the troubleshooting section found in this manual or contact Avallon for support.
Door Ajar Alarm
This Beverage Cooler includes a door ajar alarm, which will sound if one of the doors is
open for more than five (5) minutes. Leaving the door open for extended periods of time
will cause poor cooling performance and may shorten the life of the refrigerator. Keep
the door closed as frequently as possible.
Warning: Never attempt to remove frost with a sharp object.

12
Cleaning and Maintenance
Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life.
INTERIOR CLEANING:
1. Disconnect power to the unit.
2. Open the door and remove the contents and shelves.
3. Wait until the unit defrosts.
4. With a clean cloth, wipe down the interior of the unit.
5. Reinsert the shelves and beverages.
6. Reconnect power to the unit.
EXTERIOR CLEANING:
The door and cabinet may be cleaned with a mild detergent and lukewarm water solution. Do not use
solvent based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean
towel to prevent water spotting. If the door panel is stainless steel, it can discolor when exposed to chlorine
gas and moisture. Clean stainless steel with a cloth dampened with a mild detergent and warm water
solution. Never use an abrasive or caustic cleaning agent.
Preparing Your Beverage Refrigerator for Storage
If the beverage refrigerator will not be used for a long time, or is to be moved to another place, it will be
necessary to defrost the unit and dry the interior.
1. Disconnect the refrigerator from the power supply by removing the power plug from the wall socket.
2. Leave the door open to allow for air circulation and to prevent mold, mildew, and unpleasant smells.
3. Once the interior is dry and clean the unit will be ready for storage.
Important: Do NOT touch the power plug when your hands are wet. NEVER unplug the unit by pulling the
plug.
Caution: Store the unit out of the reach of children. If you have children, you may want to take additional
precautions such as removing the door to prevent a child from being trapped inside the refrigerator.

13
Troubleshooting
ISSUE
POSSIBLE CAUSE
SOLUTION
The beverage refrigerator turns on
and off frequently.
The room temperature is higher
than the recommended ambient
environment.
Run the refrigerator at the
appropriate ambient
temperature.
The door is being opened often.
Minimize the number of times the
door is opened.
The door is not completely closed.
Make sure the door is completely
closed.
The door gasket is not sealing
properly.
Make sure the door gasket is
properly sealed.
The refrigerator does not have the
suggested ventilation.
Read and follow the “Installation
Clearance Requirements” section.
The beverage refrigerator does
not turn on.
There is a power failure.
Ensure the refrigerator is plugged
in and the outlet has power.
The refrigerator is not plugged in.
Plug the unit in to a power outlet
that has sufficient amperage.
A house fuse has blown or the
circuit breaker is tripped.
Replace the broken fuse in your
fuse box or reset the breaker.
Make sure the outlet has
sufficient amperage. Reduce the
number of items sharing the
circuit.

14
ISSUE
POSSIBLE CAUSE
SOLUTION
The beverage refrigerator will not
reach the desired temperature.
The refrigerator has restricted air
flow due to too much storage.
Open up space in the cabinet to
allow air flow.
The refrigerator is placed too
close to a heat source.
Keep the refrigerator away from
direct sunlight or other heat
sources.
The refrigerator does not have
sufficient ventilation.
Read and follow the “Installation
Clearance Requirements” section.
The door is opened too frequently
or for long periods of time.
Close the door tightly and do not
open the door too frequently or
for long periods of time.
The beverage refrigerator is
making strange noises.
Certain sounds are normal
Read the “Normal Sounds”
section.
The unit is not level or is touching
another appliance.
Check to make sure the
refrigerator is level and that it is
not in contact with another
appliance or furniture.
The body of the beverage
refrigerator is electrified.
The unit is not properly grounded.
Contact your local electrician to
test your electrical grounding
system.
Frost is forming in the beverage
refrigerator.
The environment is humid.
Through the unit uses an “auto-
defrost” system, under certain
conditions, manual defrosting may
be required. If frost builds up, you
can try running the refrigerator on
a warmer temperature setting,
minimizing the number of times
you open the door, or unplugging
the unit to allow the frost to melt.
The ambient temperature is too
low.
The door is being opened too
frequently.
The door will not shut properly.
The refrigerator is not level.
Make sure the refrigerator is on a
level surface.
The door gasket is dirty.
Clean the door gasket.
The door gasket is not installed
correctly.
Make sure the door gasket is
properly installed.
The shelves are incorrectly
installed.
Install the shelves correctly.

15
Specifications
DESCRIPTION OF PRODUCT
Built-In Beverage Refrigerator
MODEL
ABR151BLSS
VOLTAGE / FREQUENCY
AC 115 / 60 Hz
AMPERAGE
1.5 A
INPUT POWER
120 W
COLOR
Black Cabinet with Black Stainless Steel Door
STORAGE CAPACITY
86 Cans*
REFRIGERANT
R600a, 1.06 oz.
TEMPERATURE RANGE
34° F to 50° F
DIMENSIONS
(HEIGHT X WIDTH X DEPTH)
34 1/8”X 14 15/16” X 25 3/8”**
NET WEIGHT
82 Pounds
*Storage capacity is based on standard 12 oz. cans. The refrigerator may experience decreased cooling
efficiency when fully loaded.
** Depth includes handle. Depth without handle is 23 11/16”.
Note: Technical data and performance information are provided for reference only. Specifications are
subject to change. Check the rating label on the beverage refrigerator for the most accurate information.