Avenview FO-DVI-DL-330X User manual

www.avenview.com
1
DVI Dual Link Extender over 2 Strand
Multi-Mode Fiber Optic Cable
Model #: FO-DVI-DL-330X
© 2011 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
Ver. 1.3

www.avenview.com
2
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1 Important Safeguards ............................................................................................................ 3
1.2 Safety Instructions ................................................................................................................. 3
1.3 Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4 Introduction ........................................................................................................................... 4
1.5 Package Contents................................................................................................................... 5
1.6 Before Installation.................................................................................................................. 5
1.7 Panel Description................................................................................................................... 6
1.8 Installation ............................................................................................................................. 7
1.9 Function Switch...................................................................................................................... 7
1.10 General Troubleshooting ....................................................................................................... 8
Section 2: Specifications....................................................................................................................... 10
2.1 Signal Pin Assignment (Single Link) ............................................................................................ 11
2.2 Signal Pin Assignment (Dual Link) .............................................................................................. 12

www.avenview.com
3
Section 1: Getting Started
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 Safety Instructions
The Avenview FO-DVI-DL-330X, DVI Dual Link Extender over Fiber Optic, has been tested for conformance to
safety regulations and requirements, and has been certified for international use. However, like all electronic
equipment’s, the FO-DVI-DL-330X should be used with care. Read the following safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.

www.avenview.com
4
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4 Introduction
Avenview FO-DVI-DL-330X Series with fiber optic cable system lets you extend dual link digital signal up to
100m (330 feet).
-High Speed and long distance transmission
-Uses 2 strand multi-mode LC fiber optic cable
-Supports both Single link and Dual link by selectable function switch
-Supports up to Dual Link WQXGA (2560 x 1600) resolution and WUXGA (1920x1200) Single link
-Self-detecting function for EDID
-Supports two mode for DDC
oReal Mode: Uses one CAT5 cable for DDC
oEmulation: Pseudo DDC detection function for EDID information (2560x1600)

www.avenview.com
5
1.5 Package Contents
Before you start the installation of the converter, please check the package contents.
-FO-DVI-DL-330X Transmitter x 1
-FO-DVI-DL-330X Receiver x 1
-Power Adapter (+5VDC 2A) x 1
-User’s Manual x 1
1.6 Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Fiber Optic Cable is not included in the package

www.avenview.com
6
1.7 Panel Description
REAR PANEL (Receiver, FO-DVI-DL-330X)
UTP port for
DDC
DVI Input
port
Power jack
Optical 2ch L
C port
UTP port for
DDC
DVI Output po
rt
Power jack
Optical 2ch L
C port

www.avenview.com
7
1.8 Installation
Avenview FO-DVI-DL-330X is composed of a transmitter and a receiver. The Transmitter should be connected
to the computer’s DVI Port and the Receiver should be connected the DVI Port of the digital display device.
Avenview FO-DVI-DL-330X Transmitter is designed to be used with the LC type standard optical cable.
Transmitter and Receiver have each of 7 Optical port which are marked on the optical port of the fiber cable
connection.
To setup Avenview FO-DVI-DL-330X follow these steps for connecting to a device:
1. Connect FO-DVI-DL-330X Transmitter unit to DVI source
2. Connect FO-DVI-DL-330X Receiver unit to DVI port of display.
3. Connect 2 Strand Fiber Optic LC Type cable to both Transmitter and Receiver.
4. Plug the power to Receiver Unit.
5. Power on DVI Source and DVI Display.
1.9 Function Switch
EDID: Switch in front of Transmitter
-REAL: EDID data of connected monitor is transmitted between Transmitter and Receiver in real time
through UTP cable.
-Emulation: Certain EDID data pre-set in the Transmitter is used in signal transmission. UTP cable is
not necessary.
MODE: Switch in front of Transmitter
-Single: When you use Single link display (up to 1920 x 1200), select ‘Single’ switch.
-Dual: When you use Dual link display (2560 x 1600), select ‘Dual’ switch.
Use the DC adapter (included in the package) for the Receiver. The Transmitter which is connected
to a computer uses power from the computer.
If Transmitter power LED doesn’t light up after PC is turned on, then use the external power adapter
for Transmitter.

www.avenview.com
8
1.10 General Troubleshooting

www.avenview.com
9
Problem
Possible Solution
Power ON
Power LED does not
work
Please check out voltage of adapter. (DC +5V)
Ensure that power adapter correctly plugged
Cannot read selected
EDID
Select switch the emulation mode
-Retry self EDID read
-Check the monitor to read EDID
Select switch the real mode.
-Please check and connected the UTP cable. (Only the direct
type)
-Please check if the DVI cable is connected.
Resolution Issue
Select single mode switch
-Max resolution 1920x1200@60Hz
-Some monitor will not support this mode.
Select dual mode switch
-Max resolution 2560x1600@60Hz
-Please check and connect DVI cable type (Should use DVI-Dual
cable)
Noise or no display
-Please check the DVI and optical fiber cable is connected.
*** The max resolution is different on to connected monitor
Self EDID Setting :
1) DDC function switch set to Emulation.
2) DVI cable connection between TX and display.
3) Supply power to TX (DC +5[V]).
4) LED blink -> LED ON

www.avenview.com
10
Section 2: Specifications
Item
Description
Units
FO-DVI-DL-330X (Transmitter)
FO-DVI-DL-330X (Receiver
Unit Description
DVI Dual Link Transmitter
DVI Dual Link Receiver
Input Signal
TMDS Signal (DVI 1.0 Standard)
Output Signal
TMDS Signal (DVI 1.0 Standard)
Video Bandwidth
1.65Gbps (Single Link)
Supported Resolution &
Distance
Single Link: WUXGA 1920 x 1200 @ 100 meters ( 330 feet)
Dual Link: WQXGA 2560 x 1600 @ 100 meters (330 feet)
Optical Converter
2 ch 850 nm Multi-Mode VCSEL
2 ch GaAs PIN photo Diode
DVI Connector
24 pin DVI-D Plug
Optical Connector
2 LC Connector
DDC Link Connector
Rj45
Fiber Type
62.5/125 µm Multi-mode glass fiber
Dimensions (L x W x H)
3.4” x 5.3” x 1”
Power Supply
5V 2A DC
Power Consumption
1.5W (max)
Environmental
Operating Temperature
32˚~ 104˚F (0˚to 40˚C)
Storage Temperature
-4˚~ 140˚F (-20˚~ 60˚C)
Relative Humidity
20~90% RH (no condensation)

www.avenview.com
11
2.1 Signal Pin Assignment (Single Link)
TRANSMITTER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
No Connect
12
No Connect
20
No Connect
5
No Connect
13
No Connect
21
No Connect
6
DDC Clock (SCL)
14
+5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-
RECEIVER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
No Connect
12
No Connect
20
No Connect
5
No Connect
13
No Connect
21
No Connect
6
DDC Clock (SCL)
14
Out +5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for Out +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-

www.avenview.com
12
2.2 Signal Pin Assignment (Dual Link)
TRANSMITTER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
T.M.D.S. Data4-
12
No Connect
20
T.M.D.S. Data5-
5
T.M.D.S. Data4+
13
No Connect
21
T.M.D.S. Data5+
6
DDC Clock (SCL)
14
+5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for +5V)
23
T.M.D.S. Clock+
8
No Connect
16
Hot Plug Detect
24
T.M.D.S. Clock-
RECEIVER
Pin
Signal Assignment
Pin
Signal Assignment
Pin
Signal Assignment
1
T.M.D.S. Data2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2 Shield
11
T.M.D.S. Data1 Shield
19
T.M.D.S. Data0 Shield
4
T.M.D.S. Data4-
12
No Connect
20
No Connect
5
T.M.D.S. Data4+
13
No Connect
21
No Connect
6
DDC Clock (SCL)
14
Out +5V Power
22
T.M.D.S. Clock Shield
7
DDC Data (SDA)
15
Ground (for Out +5V)
23
T.M.D.S. Clock+
8
No Connect
16
No Connect
24
T.M.D.S. Clock-

www.avenview.com
13
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.