AVF 467730 User manual

CUSTOMER SERVICES HELP LINE NUMBER:
[phone] (UK)
1-800 667 0808 (USA)
467730 rev00
AVF Group Ltd. Hortonwood 30, Telford, Shropshire, TF1 7YE, England
AVF Group, Inc. 2775 Broadway, Cheektowaga, Buffalo, New York, 14227 USA
www.avfgroup.com
50kg
110lbs
Read through ALL instructions before commencing installation.
If you have any questions about this product or issues with installation contact
the customer services help line before returning this product to the store.
STOP

Determine TV and Cornermount position
2 Person Installation Recommended
Assembly Overview
Tools Recommended
Stud Finder
Ø5mm (3/16")
Wood
Ø12mm (15/32")
Masonry
8mm & 13mm
Fit Support Arm Assembly
Connect TV

Retain all packaging in case the bracket needs to be returned.
Contents may vary from photography/ Illustrations.
You will not need all these parts, so expect there to be some left over depending upon the specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable standard and void of any services
(eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a sub standard wall.
Index
3Determine TV and Cornermount position
Fitting the Support Arm Assembly
4
Fitting the TV Bracket
5
6
Connecting the TV
7
Measure the TV fixing holes Width and Height
1
Fitting the TV Brackets
2
Determine TV and Cornermount Height

Boxed Parts
Hx2
C
A
B1
B2
Lx4
G
G
Templates
PT1
PT2
PT3

TV Screws, Reducers and Spacers
O1x3
Nx2
M6 M8
6mm
5mm
M6
M6 M8
U2x4 U4x4
M4 M5
25mm
U6x4
M6
25mm
25mm
V1x4 V2x4
U9x4
M8
25mm
W1x12 W2x4
U7x4
M6
45mm
U10 x4
M8
45mm
16mm
M8
U8x4
U5x4
M6
16mm
U1x4
M4
16mm
U3x4
M5
16mm
P1x2
O3x4
X1x4
Sx4
Z1x1 Z2x1
Yx1
X2x4
16mm
Qx1
M6

You are provided with 4 diameters of TV
fixing screws, M4, M5, M6 and M8.
Determine the screw diameter that fits and
remember for step 2.
Measure the TV fixing holes Width and Height
1
TV Fixing Holes
50 - 400mm
Y
50 - 600mm
X
!
If width X is greater than mm or height
Y greater than mm STOP installation now
and contact the customer help line
600
400
U5-U7
U3/U4
U1/U2
M8 =
M6 =
M4 =
M5 =
U8-U10
W1/W2
TV
TV TV TV
For TVs with flat / unobstructed back For TVs with irregular / obstructed back
WARNING
Fitting the TV Brackets
2
SpacersNo Spacers

Attach the bracket to the back of your TV using suitable screw, reducer and spacer combinations.
Top
B1
B2
U1 - U10
U3-U7
U8-U10
V1
V2
U1-U2
W1
W2
Do you need V1 or V2?
If required

PT3
PT3
3Determine TV and Cornermount Position
Ensure your TV is central
PT1
PT2PT1
Use templates , and to help you position your TV and Cornermount accurately.
Position roughly where you want
to place your TV and Cornermount.
Placing it on top of the giftbox will help
you mark your wall more accurately.
PT3
Put your TV onto template and draw around it, then cut it to shape
PT3
Ensure back of TV
is level with line
TV
Put template on top of
PT1PT2
PT2
Max Closed
Max Open Red
i
ii
iii
PT1PT3PT2
Green represents full range of extension

Ensure hole is inside slot
PT3
PT2
PT2
Extend and until they make contact with the wall.
Please note: You can only attach your Cornermount to Solid Wall or Wood Stud Wall.
If you are attaching to Wood Stud Wall the location of the wood studs will determine
where you can position and .
If you have and at max extension it is possible you will see some of the Support
Arm Assembly when you view your TV, however, you will have more movement.
If you have and at min extension it is possible you will not see any of the Support
Arm Assembly when you view your TV, however, you will have less movement.
Please consider this when positioning and .
The diagram below shows how the ends of and must make contact with the wall.
Position and on top of
PT1
iv
v
PT1
PT1PT3PT2
PT2
PT1PT2
PT1PT2
PT1
PT1PT2
PT1PT2
PT1PT2

Once you have decided on
the position of your TV and
Cornermount tape ,
and together.
Mark the wall where and
touch the wall using the lines
as a guide.
PT3
PT1PT2
Turn and slide template to see that there are no clashes. Always ensure hole is
inside slot, see step iv.
PT3
PT3
Turn Slide
vi
vii
PT2PT1
PT2
PT1
You can turn 180° and flip over so that your TV can move further in another direction.
The example shows how you can get extra movement to the left by swapping and .
PT1PT2
has only a
small amount of
adjustment to
the left
PT3
PT1PT2
PT3
can now
move further
to the left
PT3
PT3PT3
Clash
has clashed with and .
This angle of TV is not possible
PT1PT2PT3
PT2
PT3
PT1

Top
Measure from the bottom of
bracket B2 to the bottom of
your TV (dimension b )
B2
Decide how high you want the bottom of your
TV to be from the floor (dimension a ).
364+ = +
Minimum dimension c = 1000mm if using a 1 shelf module
Minimum dimension c = 1150mm if using a 2 shelf module
d is your first drill point
e is a small vertical line
Complete the sum to
get dimension c
cba
c
c
d
b
c
b
a
c
c
e
a
4Determine TV and Cornermount Height
Use the marks you made
in step 3 as a guide to
mark and
d e
i ii
iii
If you have purchased, or plan to purchase, an
additional shelf module you will need to take this into
consideration as this will affect how high the bottom of
your TV can be from the floor.
B2

!Ensure bracket is in the
centre of the wood stud
Remove dust from hole
100mm (4") Min 50 x 100mm
(2 x 4") Min
Solid Wall
75mm (3")
Ø5mm
(3/16")
Wood Stud
75mm (3")
Ø12mm
(15/32")
Concrete
!
Take care
i
Fitting the Support Arm Assembly
5
H H
H
H
12.5mm
(½") Max
YY
Position the top hole of bracket over drill point you made in step 4, and mark the
bottom drill point
Hd
!
Take care
d d
Fitting the support arm assembly takes 8 steps. Follow the 8
steps to ensure your support arm assembly is square and level.

X1x2
X2x2
!DO NOT over tighten screws.
Tighten screws by hand only
Lubricate screw thread with soap
X2x2
ii
X2x2
H
X2x2
H
X1x2
M8 M8
O3x2 Sx2
H
Solid Wall Wood Stud
Sx2
O3x2
H
e
G

iii
Yx1
Ensure part is level and align the top hole of bracket with the vertical pencil line
e you made in step 4 Mark this as drill point f
G H
H
Y
G
iv
Sx2
O3x2
G
H
H
fe
f
e

v
100mm (4") Min
50 x 100mm
(2 x 4") Min
75mm (3")
Ø12mm
(15/32")
H
H
12.5mm
(½") Max
YY
Remove dust from hole
Solid Wall Wood Stud
!
Take care
Position the top hole of bracket over drill point f you made in step iii, and mark the
bottom drill point
Hf
!
Take care
!Ensure bracket is in the
centre of the wood stud
75mm (3")
Ø5mm
(3/16")
Concrete
H H
f f

X1x2
X2x2
X2x2
X2x2 H
X2x2 H
X1x2
vi
C
G
G
!DO NOT over tighten screws.
Tighten screws by hand only
Lubricate screw thread with soap
Solid Wall Wood Stud
PT2PT1
G C
Remember to assemble
parts and in
the correct orientation.
C
G
G
PT2PT1

vii
O3
S
M8 M8
O3x4 Sx4
viii
L
L
L
L
O3
S
O3
SO3
S

6
Check bracket A is level before fully tightening
O1x3 Nx2
M6 M6 M6
P1x2
16mm
Qx1
M6
A
A
N
N
P1
P1
O1
O1
Q
O1
Y
Fitting the TV Bracket
A
i
ii

!Check all fittings are tight
Connecting the TV
7
Lock Tilt
Optional
Turn
Slide
x4

Optional Shelves
You can purchase a separate shelf module which can be built as either 1 or 2 shelves. There will
be detailed installation instructions packaged with the shelf module.