Vivo STAND-V101 User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V101

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
A (x1)
VESA Plate
B(x1)
Arm
C(x1)
Clamp
J (x1)
Thumbscrew
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Pole
E(x1)
Cable Clip
F (x1)
Grommet
Base
G(x5)
So Pad
H (x3)
Bolt
I (x1)
Support Plate
K (x1)
4mm Allen Key
Attach pole cap (M) to top of pole (D).
STEP 2
OPTION A: Clamp Installation
Stick so pads (G) to the underside of clamp (C). Attach pole (D) to clamp (C) using bolts (H). Tighten
using 4mm allen key (K). Attach clamp (C) to desktop.
M-A (x4)
M4x12
M-B (x4)
M4x16
M-C (x4)
M5x12
L (x1)
6mm Allen Key
M (x1)
Pole Cap
M-F (x4)
Spacer
M-D (x4)
M5x16
M-E (x4)
D5 Washer
M
D
10-88m m
K
H
C
G
D
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

4 5
STEP 2 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, remove
screw in top of bolt on clamp (C). Stick
so pads (G) to bottom of grommet
base (F). Attach grommet plate (I) to
bolt and run through grommet hole
into grommet base (F) and thread into
pole (D) as shown in diagram.
STEP 4
STEP 3
Slide cable management clip (E) and arm (B) onto pole (D) and tighten using 6mm allen key (L).
OPTION A: Flat Back Monitor
Attach VESA plate (A) to monitor using bolts (M-A)
or (M-C) and washers (M-E).
OPTION B: Curved Back Monitor
Attach VESA plate (A) to monitor using bolts (M-
B) or (M-D), washers (M-E), and spacers (M-F).
Slide VESA plate (A) into bracket on arm (B) and secure using thumb screws (J) as shown in diagram.
STEP 5
C
G
F
I
10-88mm
D
B
D
E
L
TV
TV
TV
TV
TV
TV
M- A
M- C
M- E
A
M- B
M- D
M- E
A
M- F
J

6 7
STEP 6 STEP 8
Store allen key (L, K) in cable management clip (E) for future adjustments.Adjust tension in monitor bracket with 6mm allen key (L).
Adjust as DesiredSTEP 7
Route cables through cable management clips.
L
K
L
180°
+45°
-45°
180°
360°
360°

Last Updated: 11/28/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654