Avid Power ACSD368 User manual

4V CORDLESS SCREWDRIVER
MODEL: ACSD368

2
TABLE OF CONTENTS
TABLE OF CONTENTS ........................................................................2
IMPORTANT SAFETY INSTRUCTIONS ..............................................3
SPECIFICATIONS.................................................................................4
FUNCTIONAL DESCRIPTION..............................................................4
OPERATION .........................................................................................5
MAINTENANCE....................................................................................7
PARTS LIST..........................................................................................8
SCHEMATIC DRAWING .......................................................................9

3
IMPORTANT SAFETY INSTRUCTIONS
The following recommendations should be strictly complied with before operating the too
in order to avoid damage to the equipment and hazard to the user.
Wear individual protection equipment if necessary (gloves, shoes, eye protectors,
breathing lters etc.). Do not wear jewels; protect long hair wear close-tting clothes.
Don't charge when you replace a tool or maintain the equipment.
Work in a clean and tidy room with su󰀩cient lighting.
Place and store the tool in a dry place far from heat or dangerous vapours (best temp
is between 10 and 15°C).Do not operate the machine close to explosive substances
or inammable matter.
This do-it-yourself equipment should be used as such and not be considered as
heavy-duty equipment.
Do not work close to people, in particular children if work is hazardous. Keep tools
away from children during and after work.
Make sure body position is steady as you work. Remember that falls constitute an
important source of accident.
Make sure you do not use the drill or screwdriver on alive parts to avoid electric shock.
(a metal detector may be used for that purpose ).Do not touch the chuck, socket or
drill bit, when the tool is working.
Do not try to open or disassemble the tool, only a specialist using original parts and
manufacturer's drawings is allowed to service the tool.
Should the case be damaged (wires or plug) have it replaced immediately by the after-
sales department.
This tool does not require special maintenance. The same applies to the electric part
of the tool.
Plastic parts should be cleaned only after disconnecting the charger. Use a wet cloth
and soft soap. Do not immerse the tool or the USB cable. The use of solvent, alcohol,
petroletc.is prohibited.
Please contact the after-sales department for complete cleaning of the tool.

4
No Load Speed: 200rpm
Chuck Size: 1/4"
Max Torque: 50 in-lbs(5.65Nm)
With 1pc USB cable
44pcs accessories:
8pcs Sockets
1pc 1” Screw bit holder
1pc 2-3/8” Screw bit holder
28pcs 1” Screwdriver bits
6pcs HSS Drill bits
1. Chuck
2. Battery Capacity Indicator
3. Two Position Adjustment Button
4. Forward/Reverse Switch
5. On/O󰀨 Trigger Switch
6. Work Light
SPECIFICATIONS
FUNCTIONAL DESCRIPTION
1
2
3
4
5
6

5
CAUTION: The safety instructions should be read carefully before operating the tool.
Power supply:
Connect one end of the USB cable to the screwdriver and the other end to the usb
charging port (such as power band, wall charger, notebook or car charger).
After 3-5 hours, three indicated lights will turn on, which represents the tool is full
charged.
LED Battery Capacity Indicator
The battery capacity is indicated by 3 lights:
Red LED is on - <20%
Red & yellow LED's are on - 20-70%
Red & yellow& green 3 LED's are on - >70%
Once only the red LED is lit, the screwdriver must be re-charged.
Two Position Adjustment
The driver can be used as one straight driver.
First press the rotation button, turn the front section in an anticlockwise direction and
then release the button when can not turn it again.
NOTICE: Do not use screwdriver as a pry bar in either position.
CAUTION: To avoid screwdriver being turned on accidentally, keep switch locked in
center position.
Installing/removing bits:
The 1/4” fast load chuck provides fast, easy one-handed bit loading and ejecting.
OPERATION

6
To install bits:
Lock forward / neutral / reverse switch on the tool by placing the direction of rotation
selector in neutral position. Pull the chuck sleeve away from the driver.
Push the bit into the chuck, release the chuck sleeve to lock bit into place.
Pull on the bit to make sure it is secured in the chuck. It's normal to have a small gap
for bit installation.
NOTE: Only use bits with quick connecting locking groove.
To remove bits:
Lock the trigger by placing the rotation selector in the neutral position.
With the nose of the tool pointed away from you, pull the chuck sleeve away from the
driver. Remove the bit from the chuck.
CAUTION: The screwdriver is not designed to be used as a drill.
Forward/Reverse switch & Trigger lock
OPERATION

7
For forward rotation, (with chuck pointed away from you) move the lever to the far left.
For reverse rotation move the lever to the far right.
To activate trigger lock move lever to the center o󰀨 position.
Do not change direction of rotation until the tool comes to a complete stop.
Shifting during rotation of the chuck can cause damage to the tool.
This screwdriver does not require special maintenance. The repair of internal parts of
the tool should be left with specialists (see safety instructions).
MAINTENANCE
OPERATION

8
PARTS LIST
No. Description Qty.
1Motor__RS380_ 3.6V 1
2 Motor gear 1
3P_ 039__08A_ Gearbox cover 1
4ISO 7045- M2.5x 5-Z --- 5S 2
5 Washer 1
6 Back star gear__plastic 3
7 Back star gear holder 1
8 Front star gear_ steel 3
9 Ring gear 1
10 Self lock block 1
11 Locking pin 6
12 Self lock ring 1
13 Lock washer 1
14 Self lock core 1
15 Bushing 1
16 Gearbox front 1
17 Pressure pin 3mm 3
18 Output axis 1
19 Pressure washer 1
20 Torque spring 1
21 Screw ring 1
22 P_ 039_ 10A_ Adjusting ring_ rear 1
23 P_ 039__11A_ _Adjusting ring_ front 1
24 P__039_ A03A_ PCB batterybar 1
25 P_ 039_ 03A_ Housing main_ upside__left 1
26 P_ 039_ 12A_ Index spring 1
27 LED_ 3mm 1
28 P_ _039_ _01A_ Housing main_ handle_ left 1
29 Compression spring 2
30 |Screw_ DIN 7981_ 2.2x4.5 2
31 P-035_ 06A__Contacts-trigger 1
32 P_ 039__06A_ _Trigger main 1
33 |P_039__07A_ Switch direction 1
34 |Switch_ SS-23E26(2P3T)_ Baohui 1
35 P-035__05B__PCB 1
36 Li-lon Battery 18650 1
37 P_ 039__02A Housing main. _handle_ right 1
38 Screw_ GB845- 1985_ 2.6x12 8
39 P_ 039 _05A_ Switch rotation 1
40 P _039__04A__Housing main_ upside_ right 1

9
SCHEMATIC DRAWING