Avid Power ACSD370 User manual

4V CORDLESS SCREWDRIVER
Any product/ return issues,
please feel free to contact us directly via
(Mon. to Sun. Any time)
MODEL: ACSD370

2
TABLE OF CONTENTS
TABLE OF CONTENTS ............................................................................... 2
IMPORTANT SAFETY INSTRUCTIONS .................................................. 3
SPECIFICATIONS ......................................................................................... 4
FUNCTIONAL DESCRIPTION .................................................................... 4
OPERATION .................................................................................................. 5
MAINTENANCE ............................................................................................ 6
PARTS LIST ................................................................................................... 7
SCHEMATIC DRAWING .............................................................................. 8

3
IMPORTANT SAFETY INSTRUCTIONS
The following recommendations should be strictly complied with before operating the too
in order to avoid damage to the equipment and hazard to the user.
Wear individual protection equipment if necessary (gloves, shoes, eye protectors,
breathing filters etc.).Do not wear jewels; protect long hair wear close-fitting clothes.
Disconnect the charger when you do not use the latter, when you replace a tool or
maintain the equipment.
Work in a clean and tidy room with sufficient lighting.
Place and store the tool in a dry place far from heat or dangerous vapours (best temp
is between 10 and 15°C).Do not operate the machine close to explosive substances
or inflammable matter.
Use tools in good conditions, adapted to the task to be performed. This do-it-yourself
equipment should be used as such and not be considered as heavy-duty equipment.
Do not work close to people, in particular children if work is hazardous. Keep tools
away from children during and after work.
Make sure body position is steady as you work. Remember that falls constitute an
important source of accident.
When drilling metal sheets, use a vice and a block of wood placed under the sheet.
Rotating metal sheets show great hazard.
Make sure you do not use the drill or screwdriver on alive parts to avoid electric shock.
Make sure you locate any electric wire or cable inside the wall before using the tool. (a
metal detector may be used for that purpose ).Do not touch the chuck, socket or drill
bit.
Do not try to open or disassemble the tool or the charger, only a specialist using
original parts and manufacturer's drawings is allowed to service the tool.
Should the case be damaged (wires or plug) have it replaced immediately by the after-
sales department.
This tool does not require special maintenance. The same applies to the electric part
of the tool.
Plastic parts should be cleaned only after disconnecting the charger. Use a wet cloth
and soft soap. Do not immerse the tool or the charger. The use of solvent, alcohol,
petroletc.is prohibited.
Please contact the after-sales department for complete cleaning of the tool.

4
SPECIFICATIONS
No Load Speed: 200rpm
Chuck Size: 1/4"
Max Torque: 40 in-lbs(4.5N.m)
With 1pc USB cable
Accessories:
1pc USB cable
1pc canvas bag
12pcs 1" Screwdriver bits
1pc 2-3/8” Screw bit holder
FUNCTIONAL DESCRIPTION
1. Keyless Chuck
2. Led Light
3. Forward/Reverse Switch
4. Trigger Switch
5. Charging Socket
6. Battery Indicator
3
2
4
5
6
1

5
OPERATION
CAUTION: The safety instructions should be read carefully before operating the tool.
Power supply:
Connect one end of the USB cable to the screwdriver and the other end to the
adapter.
Plug the adapter to the power supply, the indicated light is red.
After 3-5 hours, the indicated light is green, which represents the tool is full charged.
Installing/removing bits:
The 1/4” fast load chuck provides fast, easy one-handed bit loading and ejecting.
Place a 1/4” bit into the screwdriver collet directly.
You can also place a 1/4” bit into the magnetic bit holder and then insert the bit holder
into the screwdriver collet.
CAUTION: The screwdriver is not designed to be used as a drill.
Forward/Reverse switch & Trigger lock

6
OPERATION
For forward rotation, (with chuck pointed away from you) move the lever to the far left.
For reverse rotation move the lever to the far right.
To activate trigger lock move lever to the center off position.
Do not change direction of rotation until the tool comes to a complete
Shifting during rotation of the chuck can cause damage to the tool.
stop .
MAINTENANCE
This screwdriver does not require special maintenance. The repair of internal parts of
the tool should be left with specialists (see safety instructions).

7
PARTS LIST
No.
Description
1
lampshade
2
light board
3
hood
4
lock washer
5
plate
6
ball plate
7
shaft sleeve
8
gear box housing
9
shaft
10
self- lock ring
11
self- lock pin
12
Self- locking block
13
gear
14
star gear holder
15
ring gear
16
washer
17
motor screw
18
gear box cover
19
motor gear
20
motor
21
housing main- upside
22
hosuing fixing screw
23
housing back cover
24
trigger
25
housing main- lowerside
26
button
27
battery housing- upside
28
Li- ion battery
29
PCB
30
battery housing- lowerside
31
USB cover
32
screw

8
SCHEMATIC DRAWING