Avid Technology VENUE User manual

VENUE | Stage 64 Rack Ears 1
VENUE | Stage 64 Rack Ears
This guide shows you how to attach the included rack ears to the
VENUE | Stage 64 I/O rack and mount the rack into a flight case,
furniture or other rack housing. The ears can be installed on the
front or the back of the rack depending on the desired orientation.
Components
Mounting the Stage 64 utilizes the following components:
• (2) Stage 64 rack ears
• (18) Rack ear mounting screws (nine per rack ear) and
washers
• (8) Rack screws and washers (four per side)
• Flight case, furniture or other enclosure (not included)
Attaching the Rack Ears
The included rack ears can be installed on the front or the back of
the Stage 64. The front of the rack is where all the I/O connectors
are located, and the back of the rack is where the power switches
and associated AC connectors are located.
To attach the rack ears to Stage 64:
1Locate the rack ears and the rack ear mounting screws, in-
cluded in the Stage 64 box.
2For forward mounting, do the following:
• Position one of the rack ears at the front of the rack, making
sure it is oriented correctly for right-front or left-front loca-
tion, as appropriate.
• Insert nine rack ear screws with washers in the positions in-
dicated in the figure below, and tighten to secure the rack
ear to the rack.
• Repeatthesameproceduretoattach the otherrackear to the
other side of the rack using the other nine screws.
Avoid overheating. Be sure to maintain proper air ventila-
tion when installing the device in a rack, and do not block
the Stage 64 fans while operating the device.
Stage 64 rack ear
Rack ears attached to the front of Stage 64 (right side shown)
© 2015 Avid Technology, Inc 9320-65322-00 REV A

VENUE | Stage 64 Rack Ears2
3For reverse mounting, do the following:
• Position one of the rack ears at the back of the unit, making
sure it is oriented correctly for right-back or left-back loca-
tion, as appropriate.
• Insert the nine washers and rack ear screws in the positions
indicated in the figure below, and tighten to secure the rack
ear to the rack.
• Repeatthesameproceduretoattach the other rack ear to the
other side of the rack using the other nine screws.
Mounting Stage 64 in a Case
The Stage 64 can be installed in a standard 19-inch road case.
When the Stage 64 is forward-mounted in a case, its audio con-
nectors face the front of the case.
When the Stage 64 is reverse-mounted, its fans, power switches
and AC connectors face the front of the case.
To mount the Stage 64 in a case:
1Team lift the Stage 64 and slide it into position from the front
of its case or enclosure.
2Align the holes in the rack ears to the appropriate holes in the
rack rails attached to the case, and secure the Stage 64 using
the included rack screws and corresponding washers (four per
side).
Rack ears attached to the back of Stage 64 (right side shown)
Stage 64,forward-mounted in a flight case
Stage 64, reverse-mounted in a flight case
To make it easier to align the screw holes, tip the entire
flight case on its back (after sliding Stage 64 in).
ABCD EFGH JKLM
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
1
2
3
4
5
6
7
8
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
SIG +48V
INPUT
SRI-192
SIG MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
SIG
SIG
SIG
SIG
SIG
SIG
SIG
OUTPUT
SRO-192
1
2
3
4
5
6
7
8
AC~100-240V;60-50HZ;2.0AAC~100-240V;60-50HZ;2.0A
DO NOT OBSTRUCT FANS
SERIALNUMBER