Avital AviStart 6500 User manual

AviStart 6500 Owner's Manual - 110698 Rev. B

AviStart 6500 Owner's Manual - 110698 Rev. B
IWARNING I
!Always exercise caution and common sense when operating
your AviStart system.
!This product is intended for vehicles with fuel-injection and
automatic transmissions only. NEVER attempt to remote start
a vehicle with a manual (stick shift) transmission. Serious
injury may occur with improper use.
!NEVER attempt to remote start the engine while anyone
(including pets) is in the vehicle.
!NEVER attempt to remote start the engine while the vehicle is
in an enclosed area without sufficient ventilation.
!NEVER attempt to remote start the engine while the keys are
in the ignition.
!Always be sure the gearshift selector is in "Park" and the
emergency brake is on before attempting to remote start the
vehicle.
!Keep your AviStart remote controls out of the reach of
children.
!Whenever the vehicle is being serviced or valet parked, place
the system in Protected Valet Mode to prevent accidental or
unauthorized remote starting. See "Protected Valet Mode" on
page 6.

Table of Contents
AviStart 6500...............................2
Lifetime Warranty............................2
Remote Controls ............................2
Stealth CodingTechnology.......................3
Electronic Scan Prevention (ESP).....................3
Instant Remote Control Code Deletion..................3
One-Step Remote Control Code Learning................3
Valet Switch...............................3
Operating Your AviStart..........................4
To Arm The System ...........................4
Remote-Controlled Silent Arm/Disarm .................4
User-Programmable Long-Term Silent Arm/Disarm ...........4
Two-Stage Unlock Capability......................5
Remote Panic with Safety Locks....................5
Interior Light Illumination ........................5
User-Programmable Passive Door Lock .................5
User-Programmable Ignition-Controlled Door Lock/Unlock .......5
User-Programmable RPM Door Lock..................6
Protected Valet Mode ..........................6
Remote-Controlled Valet.........................6
LED System Status Indicator .......................7
Remote-Controlled Trunk Release Capability..............7
Remote-Controlled Accessory Outputs.................7
Zone
2
™Impact Sensor .........................8
Remote-Controlled Sensor Bypass ....................8
Previous Intrusion Alert .........................8
Specific Zone Intrusion Identification ..................8
User-Programmable Door Ajar Indication ................9
User-Programmable Siren Duration ...................9
Alarm State Memory ..........................9
Automatic Malfunction Override....................9
Remote Engine Start - Safety and Counter-Theft.............10
Remote Engine Start - Operation ....................11
User-Programmable Temperature-Controlled Starting..........12
Pit Stop Mode.............................13
User-Programmable Features.......................14
Programming Table for System Features................15
Programming Table for Remote Controls................16
1
AviStart 6500 Owner's Manual - 110698 Rev. B

AviStart 6500
Congratulations! You have just purchased the AviStart 6500, a remote engine
starter and security system manufactured by Avital Technologies, Inc. You are
about to experience the convenience and luxury of being able to start your
vehicle engine from the comfort of your home, office, department store or
other remote location.
To fullly benefit from the capabilities of your AviStart system, we encourage
you to read the Owner’s Manual thoroughly before using the system. If you
have any problems or questions regarding your AviStart system, consult the
dealer from whom you purchased this product. To locate an authorized Avital
dealer, contact Avital Technologies directly at 1-800-253-0334 (toll-free
within the U.S.) or 1-847-215-2233.
Lifetime Warranty
Avital guarantees the operation of your AviStart control unit and remote
controls for as long as you own your car. (Please refer to your Lifetime Limited
Warranty Card for complete information.) Make sure that you receive your
warranty card from your dealer, complete the required information and mail
the registration portion to Avital Technologies. You should retain the top
portion of the warranty card for your records.
Remote Controls
Included with your AviStart system are two AviGlo™ 4-button/9-channel
remote controls. Once exposed to light, the AviGlo remote control buttons
will glow, making the buttons visible in the dark.
The remote control (remote) is a miniature transmitter powered by a small
+12 volt battery. The RangeMaster™ super-heterodyne receiver (installed in
your vehicle) allows your remote to command your system from up to
¼ mile away. Obstructions, electrical or radio interference, weather
conditions, window tint or a weak battery can reduce this range. Your remote
is the key to your AviStart system and can be used to arm and disarm your
alarm, lock and unlock your doors, "pop" your trunk, start your engine and
control optional accessories.
The AviStart system can accept up to four Avital remote controls. Additional
remote controls and remote control batteries can be purchased from any
authorized Avital dealer, or by calling Avital Technologies toll-free at
1-800-253-0334 (within the U.S.) or 1-847-215-2233.
2
AviStart 6500 Owner's Manual - 110698 Rev. B

Stealth CodingTechnology
Stealth Coding technology offers the most advanced protection available
against "code-grabbing" devices which thieves may use to record the digital
code transmitted by your remote control. When you leave the area, thieves
can then play back the code to unlock the doors and deactivate your system.
Avital's remote controls with Stealth Coding randomly change the code every
time you use them, and your system will not respond if any code is
retransmitted. This technology makes code-grabbing devices useless.
Electronic Scan Prevention (ESP)
Your AviStart system also includes ESP, which blocks electronic scanner codes
preventing unauthorized operation of your system.
Instant Remote Control Code Deletion
In the event of a lost or stolen remote control, all remote controls can be
erased from the system's memory preventing unauthorized system operation.
(See the "Programming Table for Remote Controls" on page 16).
One-Step Remote Control Code Learning
The AviStart system allows you to add new remote controls in one step. (See
the "Programming Table for Remote Controls" on page 16).
Valet Switch
The valet switch is a small hidden toggle switch which allows you to control all
of the system's programmable features. (See "User-Programmable Features" on
page14).Thisswitchcanonlybecontrolledwiththeuseofyourignitionkey.
NOTE:Besuretohaveyourdealershowyouwherethevaletswitchislocated.
3
AviStart 6500 Owner's Manual - 110698 Rev. B

Operating Your AviStart
To Arm The System
The alarm can be programmed for active or passive arming. Active arming
means the alarm can only be armed by the remote control. Passive arming
means the alarm will automatically arm itself. See the "Programming Table for
System Features" on page 15.
Active Arming
Press the remote ARM/DISARM button for 1-2 seconds. The siren will chirp
twice, the parking lights will flash twice, the doors will lock, the LED will flash
slowly and the starter will be disabled.
Passive Arming
Turn the ignition key "OFF," exit the vehicle and close the doors. When the
interior lights turn off, the LED will begin flashing rapidly to indicate the alarm
is passive arming. After 30 seconds, the siren will chirp twice, the parking
lights will flash twice, the LED will flash slowly and the starter will be disabled
(at any time during passive arming, the alarm can be actively armed).
To Disarm the System
Press the remote ARM/DISARM button for 1-2 seconds. The siren will chirp
once, the parking lights will flash once, the doors will unlock, the interior
lights will turn on, the LED will turn off and the starter will be enabled.
Remote-Controlled Silent Arm/Disarm
Press the remote SILENT button for 1-2 seconds to arm or disarm your system
without the usual siren chirps.
Silent Arm Indications
The parking lights will flash twice, the doors will lock, the starter will be
disabled and the LED will flash slowly.
Silent Disarm Indications
The parking lights will flash once, the doors will unlock, the starter will be
enabled and the LED will turn off.
User-Programmable Long-Term Silent Arm/Disarm
This feature allows you to completely disable the arm/disarm siren chirps until
you decide to restore them. (See the "Programming Table for System Features"
on page 15.)
4
AviStart 6500 Owner's Manual - 110698 Rev. B

Two-Stage Unlock Capability
If the optional Two-Stage Unlock feature was installed, press the
ARM/DISARM or SILENT button for 1-2 seconds and only the driver door will
unlock. Within 3 seconds, press the ARM/DISARM or SILENT button again
and the passenger doors will unlock (may require an optional relay).
Remote Panic with Safety Locks
In a threatening situation, you can activate Remote Panic with Safety Locks.
When activated, the siren will sound and the parking lights will flash. If you
are inside your vehicle and the ignition key is "ON," the doors will lock. If you
are outside the vehicle with the ignition key "OFF," the doors will unlock.
To Activate
1.Press the remote control ARM/DISARM button for 3-4 seconds.
2. The siren will sound and the parking lights will flash.
3.If the ignition key is "OFF," the doors will unlock. If the ignition key is
"ON," the doors will lock.
To Deactivate
1.Press the remote control ARM/DISARM button for 1-2 seconds.
2. The siren will shut off and the parking lights will stop flashing.
Interior Light Illumination
When the alarm system is remotely disarmed, the vehicle interior light(s) will
turn on for 30 seconds or until the ignition key is turned on.
User-Programmable Passive Door Lock
The system will not automatically lock the doors when the alarm passively
arms to prevent the keys and remote from being locked in the vehicle. If you
prefer, you can easily program the alarm to automatically lock the doors every
time the alarm passively arms. (See the "Programming Table for System
Features" on page 15.)
User-Programmable Ignition-Controlled Door Lock/Unlock
For the ultimate in security and convenience, the AviStart is programmed to
automatically lock your doors when the ignition key is turned "ON" or the
engine is started, and will unlock when the ignition key is turned "OFF." This
feature can be programmed ON or OFF. (See the "Programming Table for
System Features" on page 15.)
5
AviStart 6500 Owner's Manual - 110698 Rev. B

User-Programmable RPM Door Lock
The system can be programmed to automatically lock the doors when the
engine reaches the factory preset RPM level. (See the "Programming Table for
System Features" on page 15). When you begin driving, your vehicle doors
will automatically lock. When you turn the ignition key off, the doors will
automatically unlock.
NOTE: Ignition-Controlled Door Lock feature must be programmed OFF.
Protected Valet Mode
You should place your system in Protected Valet Mode whenever your vehicle
is being serviced by mechanics, car wash personnel or driven by valet parking
attendants. While in the Protected Valet Mode, all remote starter and alarm
functions are bypassed to prevent unauthorized or accidental operation. If a
remote start is attempted, the parking lights will flash 4 times and the vehicle
will not start. Remote-controlled door lock/unlock , trunk release and all
optional accessories will still operate.
To Turn on Protected Valet Mode
1.Turn the ignition key to the "ON" position or start the engine.
2.Flick the valet switch to the "ON" position.
3. The LED will turn on solid red to indicate the system is in the Protected
Valet Mode.
4.Turn the ignition key to the "OFF" position.
To Turn off Protected Valet Mode
1.Turn the ignition key to the "ON" position or start the engine.
2.Flick the valet switch to the "OFF" position.
3. The LED will turn off to indicate the system is no longer in the Protected
Valet Mode.
4.Turn the ignition key to the "OFF" position.
Remote-Controlled Valet
For your convenience, the system can be put into Valet Mode via the remote
control. While in Remote-Controlled Valet, all alarm functions are bypassed.
Remote start, remote-controlled lock/unlock and all optional accessories will
still operate.
NOTE: The system must be disarmed in order to activate the
Remote-Controlled Valet feature.
6
AviStart 6500 Owner's Manual - 110698 Rev. B

To Activate Remote-Controlled Valet
1.Press the remote control ARM/DISARM and START buttons at the same
time for 1-2 seconds.
2. The parking lights will flash 4 times, and the LED will turn on solid red.
To Deactivate Remote-Controlled Valet
1.Press the remote control ARM/DISARM and START buttons at the same
time for 1-2 seconds.
2. The parking lights will flash 3 times and the LED will turn off.
LED System Status Indicator
The LED on your vehicle dashboard or center console will inform you of the
system status.
LEDStatus
OffSystem is disarmed
On solidIn Protected Valet Mode
Slow flashSystem is armed
Flashing in cyclesSee "Specific Zone Intrusion Identification" on page 8
Rapid flashPassive arming
Remote-Controlled Trunk Release Capability
If you had the optional Trunk Release feature installed, simply press the
remote control TRUNK button for 1-2 seconds to activate your vehicle
electronic trunk release. The trunk will "pop" open. This feature will only work
if your system is disarmed (may require an optional relay).
Remote-Controlled Accessory Outputs
These outputs allow you to add optional remote-controlled accessories to your
system such as a window roll-up, garage door opener or fuel door release. To
activate your optional accessories, see the "Programming Table for Remote
Controls" on page 16.
7
AviStart 6500 Owner's Manual - 110698 Rev. B

Zone2 ™Impact Sensor
The Zone2 Impact Sensor has two individual vibration/impact sensing zones.
Zone #1:
If a less threatening vibration or impact is detected, the siren will issue 2
warn-away chirps. A second violation will also issue 2 warn-away chirps. If
within 45 seconds a third violation is detected, the sensor will automatically
trigger the alarm. The siren will sound and the lights will flash.
Zone #2:
If a more threatening vibration or impact is detected at any time, the siren and
lights will activate instantly.
Remote-Controlled Sensor Bypass
You can bypass the system sensor(s) at any time. The alarm system will still
provide full perimeter protection.
To Bypass the Sensor(s):
1.Press remote SILENT and TRUNK buttons at the same time.
2. The siren will chirp twice...pause...chirp twice...pause...chirp twice.
3.The sensor(s) is now bypassed until you remotely disarm and then re-arm
your system.
Previous Intrusion Alert
If the vehicle had been tampered with and the alarm has been triggered, the
siren will chirp 3 times upon remote disarm instead of the usual 1 chirp.
Specific Zone Intrusion Identification
If the alarm had been triggered in your absence, the siren will chirp 3 times
upon remote disarm (Previous Intrusion Alert). When you enter the vehicle
and turn the ignition "ON," the LED will flash in cycles to specifically identify
which zone triggered the alarm.
LEDZone
1 flash...1 flash...Impact sensor / optional sensor input
2 flashes...2 flashes... Hood trigger
3 flashes...3 flashes... Door trigger
4 flashes...4 flashes... Trunk trigger
8
AviStart 6500 Owner's Manual - 110698 Rev. B

User-Programmable Door Ajar Indication
When you remotely arm the alarm system and a door is ajar (not closed), the
siren will chirp 2 times, then chirp 3 times and the parking lights will flash 3
times. This feature provides audible and visual indication to prevent battery
drain. (See "Programming Table for System Features" on page 15.)
NOTE: If your vehicle has factory delayed lighting, this feature will be
turned OFF.
User-Programmable Siren Duration
Upon activation, the siren can be programmed to run for 30 or 60 seconds
before it will shut off and instantly rearm. ( See the "Programming Table for
System Features" on page 15.)
Alarm State Memory
If your vehicle battery is disconnected and later reconnected, the system will
automatically return to its last state before power was removed, whether it was
armed, disarmed or in a valet mode. For example, if a mechanic disconnects
the battery while the alarm is disarmed or in a valet mode, he won't trigger the
alarm when he reconnects the battery. If a thief removes power while the
alarm is armed, and reconnects it, the alarm will instantly sound, the parking
lights will flash and the starter will be disabled.
Automatic Malfunction Override
In the event of a faulty sensor or alarm input trigger zone, the alarm, when
remotely armed, will alert you by a series of chirps and parking light flashes.
How to Interpret the Chirps and Parking Light Flashes
When you press the remote control buttons, the system will respond with
chirps and flashes of the parking lights to indicate the system status. An
explanation of these chirp/flash acknowledgements is listed below and on the
following page.
Number of chirps and flashes Explanation
1 chirp, 1 flash Disarming of the alarm.
2 chirps, 2 flashes Arming of the alarm.
2 chirps and flashes, then 3 more chirps
and flashesArmed and a door is ajar.
2 chirps and flashes, then 4 more chirps
and flashesArmed and there is a sensor malfunction (automatically bypassed).
9
AviStart 6500 Owner's Manual - 110698 Rev. B

Number of chirps and flashes Explanation
3 chirps, 3 flashesDisarmed and there was an intrusion attempt.
4 chirps, 4 flashes Armed and there is a trigger malfunction
(automatically bypassed).
0 chirps, 1 flash Remote start attempt and a fault was detected.
0 chirps, 2 flashesRemote start attempt and all zones are OK. The
vehicle will start.
2 three-second flashes
or 1 three-second flashRemote automatic temperature-controlled starting. 2 = activation, 1 = deactivation.
0 chirps, 4 light flashesRemote valet activation.
0 chirps, 3 light flashesRemote valet deactivation.
6 chirps, 0 light flashesRemote sensor bypass.
2 chirps and flashes, then 3 more chirps
and flashesArmed and a door is open or ajar.
0 chirps, 4 light flashesRemote start attempt and system is in
Protected Valet Mode.
Remote Engine Start - Safety and Counter-Theft
ICAUTION: Be sure to read the "WARNING" bulletin on the inside
cover of this manual before attempting to operate remote start.
Automatic Safety and Counter-Theft Features
Before remote starting your engine, the AviStart system will automatically
perform a safety check to ensure the following conditions have been met:
•Brake pedal is not depressed.
•Engine and ignition are turned "OFF."
•Hood is closed.
After remote starting your engine, the AviStart system will shut off the engine
immediately if the ignition is "OFF" and any of the following occurs:
•The hood is opened.
•The engine RPM rises above preset level.
•The brake pedal is pressed.
•The alarm is triggered.
•The remote control START button is pressed.
•The 20 or 30 minute programmable run time expired.
10
AviStart 6500 Owner's Manual - 110698 Rev. B

Visual Fault Indication
The AviStart has a built-in fault detection system that automatically scans all of
the safety zones, prevents the system from remote starting and provides a
visual indication if a fault is detected. The parking lights will flash 1 time if the
hood is opened or if the brake pedal is depressed and will not allow the
engine to start. If this occurs, bring your vehicle to your authorized Avital
dealer for service.
Remote Engine Start - Operation
Your AviStart system will start your vehicle engine with a touch of a button on
your AviGlo™ remote control. To cool or warm the interior of your vehicle
before you enter, set the climate control to your preference (heater, defrost or
air conditioning) before remote starting. Set the fan to a medium speed (not
maximum). Ensure the vehicle is in "Park" and the key is not in the ignition.
We strongly recommend that you arm the alarm system at all times, especially
if you are going to remote start the vehicle.
To Remote Start the Engine:
1.Press the remote control START button for 1-2 seconds, 10-15 minutes
before you enter your vehicle (this will allow the climate control time to
heat or cool the interior.) The parking lights will flash 2 times, the engine
will start and the parking lights will remain on as a visual indication that
the engine is running. Five seconds after the engine starts, the doors will
automatically lock. If you do not want the doors to automatically lock
upon remote start, this feature (Security Start Locks™) can be programmed
OFF. (See the "Programming Table for Systems Features" on page 15.)
If you have a diesel engine, the AviStart will be programmed to start 15
seconds after the parking lights flash 2 times. This will allow time for the
glow plugs to heat up. The alarm system will remain armed.
2. If the engine does not remote start, the AviStart system will attempt to start
the engine two additional times.
3.If the vehicle is left unattended, the engine will run for 20 minutes and
then shut off automatically. You can also program the system to run the
engine for 30 minutes. (See the "Programming Table for System Features"
on page 15.)
11
AviStart 6500 Owner's Manual - 110698 Rev. B

To Operate the Vehicle While Remote Started:
1.If the alarm system is armed, press the remote ARM/DISARM button for 1-2
seconds. The alarm will disarm and the doors will unlock.
2.Enter the vehicle (do not touch the brake pedal), turn the ignition key to
the "ON" position and then press the brake pedal. Pressing the brake pedal
will shut off the remote start and parking lights but the engine will remain
running.
3.You can now drive the vehicle.
To Shut Off Remote Start:
At any time while the engine is remote started, you can shut off the engine
with the remote control by pressing the remote control START button for 1-2
seconds. The engine and parking lights will shut off.
User-Programmable Temperature-Controlled Starting
ICAUTION: Do not activate Temperature-Controlled Starting while
the vehicle is in an enclosed area.
The AviStart system can be programmed to automatically start the vehicle
engine whenever the temperature inside the vehicle reaches or drops below
the preprogrammed temperature level. The AviStart will monitor the air
temperature every 2.5 hours and will only start the engine during extreme
cold temperatures. There are three temperature levels to choose from. (This
feature is programmed OFF from the factory and must be programmed ON to
operate.) (See the "Programming Table for System Features" on page 15).
To Activate:
Press the remote control TRUNK and START buttons at the same time. The
parking lights will turn on for 3 seconds, shut off for 1 second, turn on for 3
seconds and shut off. This will be your visual indication that you have
activated the Temperature-Controlled Starting feature.
When the temperature inside the vehicle reaches the preprogrammed
temperature level, the parking lights will flash 2 times, the vehicle will start
and the parking lights will turn on. The vehicle will run for 10 minutes and
then shut off. This will allow the engine to warm up and charge the battery.
12
AviStart 6500 Owner's Manual - 110698 Rev. B

To Deactivate:
Press the remote control TRUNK and START buttons at the same time for 1-2
seconds. The parking lights will turn on for 3 seconds and then turn off. This
will be your visual indication that you have deactivated the
Temperature-Controlled Starting feature.
NOTE: At any time, if the ignition key is turned on or the vehicle is remote
started, the Temperature-Controlled Starting feature will deactivate.
Pit Stop Mode
ICAUTION: Do not leave passengers or pets in the vehicle while the
system is in Pit Stop Mode.
The Pit Stop Mode allows you to park the vehicle for short-term stops, remove
the ignition key and leave the engine running.
To Activate:
1.While the vehicle engine is running with the ignition key turned "ON,"
press the remote control START button for 1-2 seconds. The parking lights
will flash 2 times and then stay on and the doors will unlock. (Make sure
the vehicle is in "Park" and set the emergency parking brake.)
2.Turn the ignition key "OFF" and the engine will stay running.
3.Remove the ignition key and remote control and exit the vehicle.
Remember to keep the ignition key and remote control in your possession.
4.Press the remote control ARM/DISARM button for 1-2 seconds to secure
your vehicle.
To Deactivate:
1.When you return to the vehicle, press the remote control ARM/DISARM
button for 1-2 seconds. The doors will unlock.
2.Enter the vehicle (do not touch the brake pedal), turn the ignition key to
the "ON" position and then press the brake pedal. The parking lights will
shut off and you will now be able to drive the vehicle.
13
AviStart 6500 Owner's Manual - 110698 Rev. B

User-Programmable Features
All AviStart system and remote control programmable features are
accomplished by turning the ignition key "ON" (or starting the engine) and
flicking the valet switch on and off a preset number of times.
The AviStart also allows you to add new remote controls in one step, delete
lost or stolen remote controls or rearrange the factory preset remote control
functions.
1.Remove the system from Protected Valet Mode. Programming cannot be
accessed while the system is in Protected Valet Mode indicated by the LED
on solid red.
2.Select the feature you wish to program from the "Programming Table for
System Features" or the "Programming Table for Remote Controls" on
pages 15 & 16.Note the number of chirps associated with that feature.
3.Turn the ignition key to the "ON" position.
4.Within 10 seconds, begin flicking the valet switch on and off. The siren
will chirp once each time you flick the switch on then off.
5. Continue flicking the switch on and off, counting the number of chirps.
NOTE: Stop when you reach the number of chirps associated with your
chosen feature.
6.Follow the "Secondary Action." You will hear a number of chirps to
confirm that you have changed the setting of that feature.
7.Turn the ignition key to the "OFF" position.
8.Repeat steps 1-7 for any other feature you wish to program.
14
AviStart 6500 Owner's Manual - 110698 Rev. B

Programming Table for System Features
FeatureFactory
SettingNo. of ChirpsSecondary Action
Active/Passive Arming Passive4Wait 3 seconds, the siren will chirp
once for Active, twice for Passive.
Passive Door LockOFF 5Wait 3 seconds, the siren will chirp
once for OFF, twice for ON.
Passive Arming Chirp/Light
Flash ConfirmationON6Wait 3 seconds, the siren will chirp
once for OFF, twice for ON
Long-Term Silent Arm/Disarm ON7Wait 3 seconds, the siren will chirp
once for OFF, twice for ON.
Siren Duration
30-60 Seconds30 8 Wait 3 seconds, the siren will chirp
once for 60, twice for 30.
Ignition-Controlled Door
Lock/Unlock ON11 Wait 3 seconds, the siren will chirp once for OFF, twice for ON.
Programmable 0 or 3 Second
Delay for Ignition-Controlled
Door Lock0 Seconds 12Wait 3 seconds, the siren will chirp
once for 3 seconds, twice for 0
seconds.
RPM Door Lock OFF13 Wait 3 seconds, the siren will chirp
once for OFF, twice for ON.
Door Ajar IndicationON14 Wait 3 seconds, the siren will chirp
once for OFF, twice for ON.
Remote Start Run Time
20 or 30 Minutes20 16 Wait 3 seconds, the siren will chirp
once for 30 minutes, twice for
20 minutes.
Temperature-Controlled Starting
OFF or 5°F (-15°C) OFF18 Wait 3 seconds, the siren will chirp
once for OFF, twice for 5°F (-15°C).
Temperature-Controlled Starting
-7°F (-20°C) or -22°F (-30 °C) —19Wait 3 seconds, the siren will chirp
once for -7°F (-20 °C), twice for -22 °F
(-30 °C).
Security Start Locks™ON20 Wait 3 seconds, the siren will chirp
once for OFF, twice for ON.
15
AviStart 6500 Owner's Manual - 110698 Rev. B

Programming Table for Remote Controls
FeatureFactory SettingNo. of
Chirps Secondary Action
Arm/DisarmARM/DISARM
Button21 Press ARM/DISARM Button, the siren will chirp 1 time.
Remote-Controlled Trunk
Release Output TRUNK Button 22 Press TRUNK button, the siren will
chirp 2 times.
Remote StartSTART Button 23 Press START Button, the siren will
chirp 3 times.
Silent Arm/DisarmSILENT Button24Press SILENT Button, the siren will
chirp 4 times.
Remote-Controlled ValetARM/DISARM +
START Buttons25 Press ARM/DISARM + START
Buttons, the siren will chirp 5 times.
Channel 6
Remote-Controlled
Accessory Output
ARM/DISARM +
SILENT Buttons26Press ARM/DISARM + SILENT
Buttons, the siren will chirp 6 times.
Remote-Controlled Sensor
Bypass TRUNK + SILENT Buttons27Press TRUNK + SILENT Buttons, the
siren will chirp 7 times.
Temperature-Controlled Start
Active/Inactive TRUNK + START Buttons28 Press TRUNK + START Buttons, the siren will chirp 8 times.
Channel 9
Remote-Controlled
Accessory Output
SILENT + START
Buttons 29 Press SILENT + START Buttons, the siren will chirp 9 times.
One-Step Remote Code
Learning ARM/DISARM Button30 Press ARM/DISARM Button, the siren will chirp 1 time.
Instant Remote Control Code
Deletion—31 Wait 3 seconds, the siren will chirp
twice, all codes are erased
out of memory.
16
AviStart 6500 Owner's Manual - 110698 Rev. B

AviStart 6500 Owner's Manual - 110698 Rev. B

AviStart 6500 Owner's Manual - 110698 Rev. B