Avonic CM22 User manual

Safety Instructions
The full safety instructions are documented in the user manual. Download the user manual at www.avonic.com
Important Precautions Repair Operation Power Adapter
Take the following precautions if the Product
should be repaired:
- Don’t open this Product and don’t attempt to
repair it yourself. Disassembling the Product may
damage it or may cause injury to you.
- If this Product is damaged, malfunctioning, or if it
comes into contact with liquid, contact Avonic or
an Avonic Authorized Service Provider.
- Repairs by service providers other than Avonic or
an Avonic Authorized Service Provider may not
involve the use of Avonic genuine parts and may
affect the safety and functionality of the device.
You can find more information about repairs and
service at www.avonic.com.
This Product is NOT intended for use where failure of
the device could lead to death, personal injury, or
severe environmental damage.
Be sure that you have COMPLETELY READ and
UNDERSTOOD ALL information in this Manual before
unpacking, installing and using this Product. Keep the
Manual in a safe place for future reference or
download it from www.avonic.com.
Failure to follow the SAFETY NOTES as described in this
chapter could result in fire, electric shock, injury, or
damage to this Product or other property.
Power this Product ONLY with the included cable
and power adapter. Other adapters may not meet
applicable safety standards, and could pose a risk of
death or injury when connected.
This applies to the operation of the camera:
- The operational activities described in this ma-
nual should ONLY be executed by people with
enough technical knowledge to perform the
activities in a safe manner.
- This Product is specifically developed for video
conferencing / streaming via internet by com-
panies, institutes and universities. It is NOT meant for
private use in the residential area.
- This Product should ONLY be used indoors.
- This Product is NOT a medical device and should
NOT be used as a substitute for professional
medical judgment. It is NOT designed or intended
for use in the diagnosis of disease or other
conditions, or in the cure, mitigation, treatment, or
prevention of any condition or disease. Please
consult your healthcare provider prior to making
any decisions related to your health.
Installation
Mounting
Ventilation
To prevent the risk of life-threatening injury or
damage to the Product or other property, caused
by electric shock or fire hazard due to overheating:
- Maintain adequate ventilation by NOT installing
or placing the Product unit in a bookcase, built-in
cabinet or any other confined space.
- Ensure that curtains or any other material does
NOT obstruct the ventilation.
Handling
This applies to the installation of the camera:
- The installation activities described in this Quick
Guide should ONLY be executed by experienced
technicians.
- The installation activities should NOT be execu-
ted by minors, mentally disabled persons or other
persons not qualified to perform these tasks.
Atmospheric conditions
To prevent the risk of injury or damage to the
Product or other property caused by a potentially
explosive atmosphere:
- Do NOT use this Product in an area with a
potentially explosive atmosphere, such as areas
where the air contains high levels of flammable
chemicals, vapors, or particles (such as grain, dust,
or metal powders), may be hazardous.
- Exposing this Product to environments having
high concentrations of industrial chemicals,
including near evaporating liquified gasses such
as helium, may damage or impair this Product
functionality.
- Obey all signs and instructions.
To prevent the risk of injury, take the following
precautions when handling this Product:
- Handle the Product with care. It is made of me-
tal, glass, and plastic and has sensitive electronic
components inside.
- The Product can be damaged if dropped, bur-
ned, punctured or crushed, or if it comes into
contact with liquid.
- Do not pick up and move the Product unit while
a tripod is attached. The fitting may break under
the weight of the tripod, which may result in injury.
- If you suspect damage to the Product, discon-
tinue its use, as it may cause overheating or injury.
To prevent the Product from falling down which
may cause injuries:
- Set up this Product on a hard, stable surface or
mount it to a wall or (computer) screen.
- ONLY use an Avonic mount for mounting to a wall
or (computer) screen.
- Ensure the mounting construction is capable of
supporting four times the weight of the Product.
(See 'General Specifications > Weight product’ in
the Product Datasheet for the exact weight.) Use a
safety loop or drop protection that prevents the
Product from falling if the mounting construction
fails.
- During installation, NEVER install a Product above
a person.
- Check the installation at least once a year. An
improper mounting could cause the unit to fall off,
resulting in personal injury.
To prevent the risk of life-threatening injury or
damage to the Product or other property, caused
by electric shock or fire hazard:
- Power this Product ONLY with the included cable
and power adapter. Other adapters may not
meet the applicable safety standards. They could
pose a risk of death or injury when connected.
- Do NOT use damaged cables.
- Do NOT power the Product in a moist / wet en-
vironment.
- Before you power the Product, ensure the cable
is fully inserted into the power adapter.
- Plug the power adapter directly into a power
outlet.
- Do NOT use the power adapter at a moist / wet
location.
- Do NOT connect or disconnect the power
adapter with wet hands.
- Keep the Product, cable, and power adapter in
a dry and well-ventilated area when in use.
- Stop using the power adapter and any cables if
any of the following conditions exist:
* The power adapter plug or prongs are dama-
ged.
* The cable becomes frayed or otherwise da-
maged.
* The power adapter is exposed to excessive
moisture, or liquid is spilled into it.
* The power adapter has been dropped, and its
enclosure is damaged.

QUICK GUIDE
1. Unbox 6. Control multiple cameras with one remote
Be gentle with the CM22, hold the camera only at its
base.
2. USB connection
Do you have multiple cameras and do you want to
control them with 1 remote?
1. Default IR ID is 1. Give every camera a unique IR ID.
2. Turn on only camera 2 and press [*] → [#] → [F2].
3. Turn on only camera 3 and press [*] → [#] → [F3]. etc.
7. Complete Manual
Download the manual at avonic.com.
CE Marking
1. Connect the camera with the USB3.0 cable to a
computer. Use a USB3.0 port for optimal quality.
2. The camera is USB powered, no separate power
supply is needed.
3. The built-in microphone picks up audio within 3 meter
(10ft) and embeds this signal onto the USB output.
3. HDMI connection
This product has a CE marking on the productlabel.
This is placed on the bottom of the camera.
Contact
1. Connect the camera to a display using a third party
HDMI cable.
2. Connect the included USB cable to the USB port to
power the camera. You can use a third-party USB
device to power the camera.
3. Please note that the microphone signal is not
embedded onto the HDMI output.
4. On Screen Display
1. Insert 2 LR03 AAA batteries in the remote control.
2. Open an Video application app.
3. Press “menu” on the remote control to open the
"On Screen Display".
This Quick Guide is written with great care. If you have
any questions, remarks or suggestions, do not hesitate
to contact us. Our support team is there to assist you in
getting the best result. You can reach us as follows:
•Telephone: [phone]
•Email: [email protected]
5. Configure the camera
1. Does your room have changing light conditions?
Choose auto-white balance, otherwise set the
white-balance to fixed.
2. Test which anti-flicker gives the best results. Let's create a story!