Avonic CM41-VCUC User manual

SAFETY INSTRUCTIONS
The full safety notes are documented in the users manuals. Download the user manual at www.avonic.com
Important Precautions Repair Power Adapter
Take the following precautions if the Product
should be repaired:
- Don’t open this Product and don’t attempt to
repair it yourself. Disassembling the Product may
damage it or may cause injury to you.
- If this Product is damaged, malfunctioning, or if it
comes into contact with liquid, contact Avonic or
an Avonic Authorized Service Provider.
- Repairs by service providers other than Avonic
or an Avonic Authorized Service Provider may not
involve the use of Avonic genuine parts and may
affect the safety and functionality of the device.
You can find more information about repairs and
service at www.avonic.com.
This Product is NOT intended for use where failure of
the device could lead to death, personal injury, or
severe environmental damage.
Be sure that you have COMPLETELY READ and
UNDERSTOOD ALL information in this Manual be-
fore unpacking, installing and using this Product.
Keep the Manual in a safe place for future re-
ference or download it from www.avonic.com.
Failure to follow the SAFETY NOTES as described in
this chapter could result in fire, electric shock, injury,
or damage to this Product or other property.
Power this Product ONLY with the included cable
and power adapter. Other adapters may not
meet applicable safety standards, and could
pose a risk of death or injury when connected.
Operation
This applies to the operation of the camera:
- The operational activities described in this Ma-
nual should ONLY be executed by people with
enough technical knowledge to perform the
activities in a safe manner.
- This Product is specifically developed for video
conferencing / streaming via internet by compa-
nies, institutes and universities. It is NOT meant for
private use in the residential area.
- This Product should ONLY be used indoors.
- This Product is NOT a medical device and should
NOT be used as a substitute for professional me-
dical judgment. It is NOT designed or intended for
use in the diagnosis of disease or other con-
ditions, or in the cure, mitigation, treatment, or
prevention of any condition or disease. Please
consult your healthcare provider prior to making
any decisions related to your health.
Installation
Mounting
Ventilation
To prevent the risk of life-threatening injury or
damage to the Product or property, caused by
electric shock or fire hazard due to overheating:
-Maintain adequate ventilation by NOT installing
or placing the Product unit in a bookcase, built-in
cabinet or any other confined space.
-Ensure that curtains or any other material does
NOT obstruct the ventilation.
This applies to the installation of the camera:
- The installation activities described, should ONLY
be executed by experienced technicians.
- The installation activities must NOT be executed
by minors, mentally disabled persons or persons
not qualified to perform these tasks
Handling
Atmospheric conditions
To prevent the risk of injury or damage to the Pro-
duct or other property caused by a potentially
explosive atmosphere:
-Do NOT use this Product in an area with a po-
tentially explosive atmosphere, such as
areas where the air contains high levels of
flammable chemicals, vapors, or particles
(such as grain, dust, or metal powders), may be
hazardous.
-Exposing this Product to environments having
high concentrations of industrial chemicals,
including near evaporating liquified gasses
such as helium, may damage or impair this
Product.
-Obey all signs and instructions.
To prevent the risk of injury, take the following
precautions when handling this Product:
- Handle the Product with care. It is made of metal,
glass, and plastic and has sensitive electronic com-
ponents inside.
-The Product can be damaged if dropped, bur-
ned, punctured or crushed, or if it comes into con-
tact with liquid.
-Do not pick up and move the Product unit while
a tripod is attached. The fitting may break under
the tripod's weight, which may result in injury.
- If you suspect damage to the Product, do not use it,
as it cause overheating or injury.
To prevent the Product from falling down which
may cause injuries:
- Set up this Product on a hard, stable surface or
mount it to a wall or ceiling.
-ONLY use an Avonic mount for mounting to a
wall or ceiling.
-Ensure the mounting construction is capable of
supporting four times the weight of the Product.
(See 'General Specifications > Weight product’ in
the Product Datasheet for the exact weight.) Use
a safety loop or drop protection that prevents the
Product from falling if the mounting construction
fails.
-During installation, NEVER install a Product above
a person.
-Check the installation at least once a year. An
improper mounting could cause the unit to fall off,
resulting in personal injury.
To prevent the risk of life-threatening injury or
damage to the Product or other property, caused
by electric shock or fire hazard:
- Power this Product ONLY with the included cable
and power adapter. Other adapters may
not meet the applicable safety standards. They
could pose a risk of death or injury when con-
nected.
- Do NOT use damaged cables.
- Do NOT power the Product in a moist / wet envi-
ronment.
- Before you power the Product, ensure the cable
is fully inserted into the power adapter.
- Plug the power adapter directly into a power outle t.
- Do NOT use the power adapter at a moist / wet
location.
- Do NOT connector disconnect the power adap-
ter with wet hands.
- Keep the Product, cable, and power adapter in
a dry and well-ventilated area when in use.
- Stop using the power adapter and any cables if
any of the following conditions exist:
* The power adapter plug or prongs are damaged.
* The cable becomes frayed or otherwise damaged.
* The power adapter is exposed to excessive
moisture, or liquid is spilled into it.
*The power adapter has been dropped, and its
enclosure is damaged.

QUICK GUIDE
1. Unbox 7. Control Multiple Cameras With One Remote
Be gentle with the moving parts, hold the
camera at the bottom. The camera is packed
in a sealed bag, if the seal has been breached,
contact Avonic.
2. WebGui
Do you want to control multiple cameras with one
remote? If so, note that the default IR ID is 1. Give
every camera an unique IR ID as follows:
•Turn on camera 2 and press [*] + [#] + [F2].
•Turn on camera 3 and press [*] + [#] + [F3].
•etcetera
The WebGUI can be found at 192.168.5.163
username “admin” and password “admin”.8. Complete Manual
3. Connect the Power cable to the camera Download the manual from www.avonic.com
(Products > Cameras > CM44/ CM41)
9. CE Marking
Connect the provided PSU to the camera.
Connect also an ethernet cable to the camera
or connect the camera via USB to a computer.
4. ON/ OFF
This product has a CE marking on the productlabel.
This is placed on the bottom of the camera.
10. Support website
This camera is equipped with a physical ON/
OFF button. Make sure that this button is set to
‘ON’. After switching on, the lens will make a
complete rotational cycle. The lens will face
center forwards or to a start-up preset after
finishing the bootcycle.
5. On Screen Display (OSD)
We’ve created a knowledge base in which you
can find frequently asked questions and interesting
articles for you to read. This page also contains a
quick way for you to drop a support ticket or give
support a call. Add support.avonic.com to your
favorites and you’re ready for every challenge that
comes your way.
11. Contact
Insert 2 LR03 AAA batteries and press MENU on
the Remote Control to open the OSD menu.
6. Configure the Cameras You can reach us by telephone [phone],
WhatsApp for business [phone] or via
email [email protected]
Does your room have changing light
conditions? If so, choose ‘auto white balance’,
otherwise set the white balance to ‘fixed’. Test
which anti-flicker settings gives the best results in
your room. Let's create a story!