Avtech ZOOMMOVER19 User manual

User Manual
ZOOMMOVER19
LED Zoom Moving Head

1.1 Unpacking
1.2 Safety Instructions
Carefully unpack the carton, check the contents to ensure that all parts are present,
and have been received in good condition. Contact your supplier immediately and
retain packing material for inspection if any part is missing or damaged.
1. INTRODUCTION
■1 x Zoom Moving 19Q
■1 x Power Cord
■1 x Mounting bracket
■1 x User Manual
▪The product is for indoor use only.
▪Always turn off, unplug power and allow fixture to cool before servicing.
▪Ensure that fixture is properly grounded.
▪Please keep this User Guide for future consultation.
▪Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on decal or rear panel of
the fixture.
▪Always disconnect from power before servicing or replacing fuse.
▪Make sure power cord is never crimped or damaged.
!
Warning!!! To reduce the risk of fire, electric shock, or injury to persons,
follow these important safety instructions:
The following items are included in the box:
Caution!
Avaid looking directly into the LED light beam at a close distance!
1
Thank you for selecting the LED Zoom Moving Head. It features 5° - 50° motorized
zoom. With 19 x 15W OSRAM Ostar RGBW 4in1 LEDs, it produces extremely bright
and unlimited colors. Great for stages, live shows, clubs, bars, etc. To optimize the
performance of this product, please read the user manual carefully before use.
4
16 DMX Channels
Channel DMX Value Functions
7 Pan movement 540°0-255
10
8
11
12
Fine control of Pan
Fine control of Tilt
0-255
Tilt movement 270°0-255
Pan
Pan Fine
Tilt
Tilt Fine
Pan & Tilt speed from fast to slowP/T Speed
1
2
3
4
5
6
Dimmer
0-255
0-255
0-255 0-100%
13 Strobe
14 Programs
15 Program Sp
0-10 No function
11-255 Strobe from slow to fast
0-49 No function
No function
50-99 Auto program 1
Auto program 2
Auto program 3
Auto program 4
100-149
150-199
200-249
250-255 Sound activation mode
0-255 Auto program speed from slow to fast
16 Reset 0-249
5s for Reset250-255
0-255
0-255
0-255
0-255
0-4
5-255
No function
Built-in colors
Red
Green
Blue
White
Red intensity 0-100%
Green intensity 0-100%
Blue intensity 0-100%
White intensity 0-100%
Color Macro
9 Zoom 0-255
Zoom 6° - 60°

3.1 Menu Map
3. OPERATION INSTRUCTIONS
3
1st Level 2nd Level 3rd Level
Mode
set
test
offset
advance
Info
DMX-CH16
SOUND
AUTO1
AUTO2
AUTO3
AUTO4
Address
Reset
Language
Sens (Sensitivity)
Ch15
PanOffset
PowerCtrl
Ch1
Ch2
001-512
OK
English/中文
010 - 100
000-255
000-255
000-255
000-255
TiltOffset 000-255
ZoomOffset 000-255
ROffset 000-255
GOffset 000-255
BOffset 000-255
WOffset 000-255
Smooth (Dimmer) OFF/LV1/LV2/LV3/LV4
ScreenSaver ON/OFF
DisplayInv ON/OFF
CodeWheel ON/OFF
ON/OFF
TempSet 030 - 100
PanRev ON/OFF
TiltRev ON/OFF
P & T Swap ON/OFF
Temperature xxxx
xxxxTotlaTime
xxxx
xxxx
xxxx
OnTime
Signal
Version
DMXTimeOut KEEP/BLACK
Factoryset
The Moving Head is fully operational in any mounting position, hanging upside-down,
side mounted, or set on a flat llevel surface, etc.
1.3 Features
1.4 Product overview
Control panel Rear panel
2. SETUP
2.1 Mounting
▪19 x 15W Quad-colour LEDs (RGBW)
▪Beam angle: 5° - 50° adjustable
▪Pan/tilt auto correction
▪Pan: 540 degrees, Tilt: 220 degrees
▪0 - 100% dimming and variable strobe
▪DMX channels: 16
▪LCD display with rotary wheel
▪Powercon in/out sockets
▪3-pin & 5-pin XLR in/out sockets
▪Omega clamps included
2
IMPORTANT!!! Safety cables must always be used when unit is celling or truss
mounted. The safety cable must be capable of holding 10 times the weight of the
fixture.
The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered
directly from a switched circuit. This unit cannot be run on a rheostat or dimmer
circuit even if used solely for a 0% to 100% switching.
2.3 AC Power
WARNING!!! All fixtures must be connected to circuits with a
suitable Earth Ground.
ERR
DMX
Go forwardGo backward
Go up
Go down
Enter

3.1 Menu Map
3. OPERATION INSTRUCTIONS
3
1st Level 2nd Level 3rd Level
Mode
set
test
offset
advance
Info
DMX-CH16
SOUND
AUTO1
AUTO2
AUTO3
AUTO4
Address
Reset
Language
Sens (Sensitivity)
Ch15
PanOffset
PowerCtrl
Ch1
Ch2
001-512
OK
English/中文
010 - 100
000-255
000-255
000-255
000-255
TiltOffset 000-255
ZoomOffset 000-255
ROffset 000-255
GOffset 000-255
BOffset 000-255
WOffset 000-255
Smooth (Dimmer) OFF/LV1/LV2/LV3/LV4
ScreenSaver ON/OFF
DisplayInv ON/OFF
CodeWheel ON/OFF
ON/OFF
TempSet 030 - 100
PanRev ON/OFF
TiltRev ON/OFF
P & T Swap ON/OFF
Temperature xxxx
xxxxTotlaTime
xxxx
xxxx
xxxx
OnTime
Signal
Version
DMXTimeOut KEEP/BLACK
Factoryset
The Moving Head is fully operational in any mounting position, hanging upside-down,
side mounted, or set on a flat llevel surface, etc.
1.3 Features
1.4 Product overview
Control panel Rear panel
2. SETUP
2.1 Mounting
▪19 x 15W Quad-colour LEDs (RGBW)
▪Beam angle: 5° - 50° adjustable
▪Pan/tilt auto correction
▪Pan: 540 degrees, Tilt: 220 degrees
▪0 - 100% dimming and variable strobe
▪DMX channels: 16
▪LCD display with rotary wheel
▪Powercon in/out sockets
▪3-pin & 5-pin XLR in/out sockets
▪Omega clamps included
2
IMPORTANT!!! Safety cables must always be used when unit is celling or truss
mounted. The safety cable must be capable of holding 10 times the weight of the
fixture.
The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered
directly from a switched circuit. This unit cannot be run on a rheostat or dimmer
circuit even if used solely for a 0% to 100% switching.
2.3 AC Power
WARNING!!! All fixtures must be connected to circuits with a
suitable Earth Ground.
ERR
DMX
Go forwardGo backward
Go up
Go down
Enter

1.1 Unpacking
1.2 Safety Instructions
Carefully unpack the carton, check the contents to ensure that all parts are present,
and have been received in good condition. Contact your supplier immediately and
retain packing material for inspection if any part is missing or damaged.
1. INTRODUCTION
■1 x Zoom Moving 19Q
■1 x Power Cord
■1 x Mounting bracket
■1 x User Manual
▪The product is for indoor use only.
▪Always turn off, unplug power and allow fixture to cool before servicing.
▪Ensure that fixture is properly grounded.
▪Please keep this User Guide for future consultation.
▪Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on decal or rear panel of
the fixture.
▪Always disconnect from power before servicing or replacing fuse.
▪Make sure power cord is never crimped or damaged.
!
Warning!!! To reduce the risk of fire, electric shock, or injury to persons,
follow these important safety instructions:
The following items are included in the box:
Caution!
Avaid looking directly into the LED light beam at a close distance!
1
Thank you for selecting the LED Zoom Moving Head. It features 5° - 50° motorized
zoom. With 19 x 15W OSRAM Ostar RGBW 4in1 LEDs, it produces extremely bright
and unlimited colors. Great for stages, live shows, clubs, bars, etc. To optimize the
performance of this product, please read the user manual carefully before use.
4
16 DMX Channels
Channel DMX Value Functions
7 Pan movement 540°0-255
10
8
11
12
Fine control of Pan
Fine control of Tilt
0-255
Tilt movement 270°0-255
Pan
Pan Fine
Tilt
Tilt Fine
Pan & Tilt speed from fast to slowP/T Speed
1
2
3
4
5
6
Dimmer
0-255
0-255
0-255 0-100%
13 Strobe
14 Programs
15 Program Sp
0-10 No function
11-255 Strobe from slow to fast
0-49 No function
No function
50-99 Auto program 1
Auto program 2
Auto program 3
Auto program 4
100-149
150-199
200-249
250-255 Sound activation mode
0-255 Auto program speed from slow to fast
16 Reset 0-249
5s for Reset250-255
0-255
0-255
0-255
0-255
0-4
5-255
No function
Built-in colors
Red
Green
Blue
White
Red intensity 0-100%
Green intensity 0-100%
Blue intensity 0-100%
White intensity 0-100%
Color Macro
9 Zoom 0-255
Zoom 6° - 60°

IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that old
appliances contain and reduce the impact on human health and the
environment, ensure that this product is recycled at the end of its life.
5. Specifications
Source: 19 x 15W RGBW 4in1 LEDs
Beam angle: 5° - 50° Motorized zoom
Power consumption: 260W
Power supply: AC 100~240V, 50-60Hz
Fuse: F4A / 250V
Dimensions: 325 x 188 x 395 mm
Weight: 9.0 kg
5
4. General Maintenance
a. Unscrew the fuse holder and remove the damaged fuse.
b. Replace with exact same type fuse and screw the fuse holder back in its place.
4.1 Fuse Replacement