Panasonic PT-DZ21KU User manual

SPEC FILE
Product Number : PT-DZ21K
Product Name : 3-Chip DLP ™Projector
As of September 2012. Specifications and appearance are subject to change without notice.
SFD12M005-1
1/19
The PT-DZ21K is not e uipped with a lens.

SPEC FI L E
PT-DZ21K
3-Chip DLP™Projector
As of September 2012
SFD12M005-1
2/19
Specifications
ain unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Lamp
Screen size
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency SD
HDM /DV -D
RGB
YPBPR(YCBCR)
Video/S-Video
200–240 V AC, 12 A, 50/60 Hz (3-wire single-phase)
2,300 W (2,350 VA) (0.3 W with STANDBY MODE set to ECO.* 19Wwith
STANDBY MODE set to NORMAL.),
max. 7,848 BTU (without light output: 7,585 BTU )
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™ chip × 3 (R, G, B), DLP™ projection system
2,304,000 (1,920 × 1,200) × 3, total of 6,912,000 pixels
Optional powered zoom/focus lenses
465 W UHM lamps (× 4) (four lamp system)
1.78–15.24 m (70–600 inches) (1.78–7.62 m (70 – 300 inches) with the
ET-D75LE50), 16:10 aspect ratio
20,000 lumens (four lamp)
90%
10,000:1 (full on/full off, in dynamic iris 3 mode)
1,920 × 1,200 pixels ( nput signals that exceed this resolution will be
converted to 1,920 × 1,200 pixels.)
Dual-link HD-SD signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 372 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p,
Dual-link HD-SD signal (X´Y´Z´4:4:4 12-bit):
SMPTE ST 372 compliant: 2048 × 1080/24p, 2048 × 1080/24sF,
3G-SD signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p,
3G-SD signal (YPBPR4:2:2 10-bit):
SMPTE ST 424 compliant: 1080/50p, 1080/60p,
HD-SD signal (YPBPR4:2:2 10-bit):
SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i,
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p,
SD-SD signal (YCBCR4:2:2 10-bit):
SMPTE ST 259 compliant: 480i, 576i
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA (1,920 × 1,200), compatible with
non-interlaced signals only, dot clock: 25 –162 MHz
Horizontal: 15–100 kHz, vertical: 24 – 120 Hz,
dot clock: 162 MHz or less
480i (525i): fH15.75 kHz; fV60 Hz,
576i (625i): fH15.63 kHz; fV50 Hz,
480p (525p): fH31.50 kHz; fV60 Hz,
576p (625p): fH31.25 kHz; fV50 Hz,
720 (750)/60p: fH45.00 kHz; fV60 Hz,
720 (750)/50p: fH37.50 kHz; fV50 Hz,
1035/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/50i: fH28.13 kHz; fV50 Hz,
1080/25p: fH28.13 kHz; fV25 Hz,
1080/24p: fH27.00 kHz; fV24 Hz,
1080/24sF: fH27.00 kHz; fV48 Hz,
1080/30p: fH33.75 kHz; fV30 Hz,
1080/60p: fH67.50 kHz; fV60 Hz,
1080/50p: fH56.25 kHz; fV50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]

SPEC FI L E
PT-DZ21K
3-Chip DLP™Projector
As of September 2012
SFD12M005-1
3/19
Optical axis shift Vertical
Horizontal
Keystone correction range
Keystone correction range when using the
optional upgrade kit ET-UK20*3
nstallation
Terminals SD N 1
SD N 2
HDM N
DV -D N
RGB 1 N
R, G, B
Y, PB, PR(Y, CB, CR)
S-Video signal
RGB 2 N
R, G, B
Y, PB, PR(Y, CB, CR)
V DEO N
3D SYNC 1 N/OUT
3D SYNC 2 OUT
SER AL N
SER AL OUT
REMOTE 1 N
REMOTE 1 OUT
±55% (±44% with the ET-D75LE6) from center of screen, powered
±20% (±15% with the ET-D75LE6) from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the
ET-D75LE50.
Vertical ±40°, horizontal ±15°
(vertical ±22° and horizontal ±15° with the ET-D75LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6)
Vertical ±45°, horizontal ±40°
(vertical ±22° and horizontal ±15° with the ET-D75LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6,
vertical ±40° and horizontal ±40° with the ET-D75LE10/D75LE20)
Ceiling/floor, front/rear
BNC × 1,
Dual-link HD-SD signal: SMPTE ST 372 compliant (Link-A)
3G-SD signal: SMPTE ST 424 compliant
HD-SD signal: SMPTE ST 292 compliant
SD-SD signal: SMPTE ST 259 compliant
BNC × 1,
Dual-link HD-SD signal: SMPTE ST 372 compliant (Link-B)
HD-SD signal: SMPTE ST 292 compliant
SD-SD signal: SMPTE ST 259 compliant
HDM 19-pin × 1, Deep Color, compatible with HDCP,
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480) – WUXGA*4(1,920 × 1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
DV -D 24-pin × 1, DV 1.0 compliant, HDCP compatible,
for single link only
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA*4(1,920 × 1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
nput: TTL, high impedance. Output: TTL, max. 10 mA
BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
D-sub 9-pin (female) × 1 for external control (RS-232C compliant)
D-sub 9-pin (male) × 1 for link control
M3 jack × 1 for wired remote control
M3 jack × 1 for link control

SPEC FI L E
PT-DZ21K
3-Chip DLP™Projector
As of September 2012
SFD12M005-1
4/19
REMOTE 2 N
LAN
Power cord length
Cabinet materials
Dimensions (W × H × D):
Weight*7
Operation noise*2
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*9
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Zoom lens (0.9 – 1.1:1)
Zoom lens (1.3 – 1.7:1)
Zoom lens (1.7– 2.4:1)
Zoom lens (2.4 – 4.7:1)
Zoom lens (4.6 – 7.4:1)
Zoom lens (7.3 – 13.8:1)
Fixed-focus lens (0.7:1)
Lens motor cover
Ceiling mount bracket
Frame
Smoke cut filter
Upgrade kit
Replacement lamp unit
Replacement lamp unit for portrait mode
Replacement filter unit
D-sub 9-pin × 1 for external control (parallel)
RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant
with PJLink™ (class 1)
3.0 m (9 ft 10 in)
Molded plastic
620 × 291*5× 800*6mm
(24-7/16 × 11-15/32*5× 31-1/2*6inches) (without lens)
Approx. 43 kg (94.8 lbs) (without lens)
49 dB (quad lamp operation)
0°– 45°C (32°–113°F)*8
10%–80% (no condensation)
3 V DC (AA type battery × 2)
Approx. 30 m (98 ft 5 in) when operated from directly in front of the
signal receptor
51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches)
Approx. 134 g (4.7 oz) (including batteries)
Power cord with security lock (× 1)
Wireless/wired remote control unit (× 1)
Batteries for remote control (AA type × 2)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
ET-D75LE6
ET-D75LE10
ET-D75LE20
ET-D75LE30
ET-D75LE40
ET-D75LE8
ET-D75LE50
ET-D75MC1
ET-PKD510H (for high ceilings)
ET-PKD510S (for low ceilings)
ET-PFD510
ET-SFR510
ET-UK20
ET-LAD510 (one bulb)
ET-LAD510F (a set of four bulbs)
ET-LAD510P (one bulb)
ET-LAD510PF (a set of four bulbs)
ET-EMF510
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output termi-
nal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
*2 easurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 Up to a total of ±55° during simultaneous horizontal and vertical correction.
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 With legs at shortest position.
*6 Excluding the optional lens.
*7 Average value (excluding the optional lens). ay differ depending on models.
*8 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the FAN CONTROL is set to HIGH ALTITUDE ODE (for altitudes from 1,400 m
to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature
range is 0 °C to 35 °C (32 °F to 95 °F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 °C to
40 °C (32 °F to 104 °F) when the ET-LAD510P/LAD510PF lamp is mounted and the projector is used in portrait configuration. The operating tem-
perature range is 0 °C to 35 °C (32 °F to 95 °F) when the FAN CONTROL is set to HIGH ALTITUDE ODE (for altitudes from 1,400 m to 2,700 m (4,593 ft
to 8,858 ft) above sea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature range is 0 °C to 30 °C
(32 °F to 86 °F).
*9 Operation range differs depending on environments.

73 0 ( 28 - 3 /4 )
8 00 ( 31-1/2 )
70
( 2- 3 /4 )
620 (24-13/32)
244
( 9 -19 / 32 ) 608
(23-15/16 )
47
(1-27/32)
244
( 9 -19 / 32 )
177
( 6 -31/ 3 2)
291 (11-15/ 32)
36
(1-13 / 32)
Dimensions
SPEC FILE
PT-DZ21K
3-Chip DLP™Projector
As of September 2012
SFD12M005-1
5/19
Terminals
1
6 7 8 9 10 11 12 13 14 15
23 4 5
1 Remote 1 input
2 Remote 1 output
3 Remote 2 input
4 Serial input
5 Serial output
6 SD 1 input
7 SD 2 input
8 HDM input
9 RGB 1 input
10 RGB 2 nput
11 DV -D input
12 Video input
13 3D sync 1 input/output
14 3D sync 2 output
15 LAN connector
unit : mm (inch)
NOTE: This illustration is not drawn to scale.