Avue HDMI-EC200 User manual

HDMI EXTENDER OVER CAT5e/6/7
HDMI-EC200
FEATURES
Supported Video Input: 1080p/1080i/720p/576p/576i/480p/480i @ 24/50/60fs
Supported Video Output: 1080p/1080i/720p/576p/576i/480p/480i @ 24/50/60fs
Supported Audio Formats: DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD
Use single CAT6/5e cable up to 200 feet between sender and receiver units.
Supports 3D
LED status indicator
No loss of quality
Installs in minutes
WHAT’S IN THE BOX
1x Sender (TX) Unit
1x Receiver (RX) Unit
2x 5V Power Adapter
User’s Manual
DIAGRAMS
CAT: Use single CAT cable to connect Sender and Receiver
Switcher: Reads EDID information of incompatible display source to adapt.
1. Connect power adaptor to TX unit.
2. Connect HDMI cable with output of TX to HDMI input of display.
3. Keep the display on and choose the matching HDMI input port.
4. Press Switcher button on TX to adapt to display. Status LED will turn green
when finished adapting from EDID information.
5. Take HDMI cable out and power off the TX.
Adapted EDID settings will take affect when powered on again.
NOTE: These steps also work for HDMI-DVI cable for DVI display.
HDMI IN: Signal Source Input
HDMI OUT: Receiver to connect the HDTV or other display
DC 5V: 5V DC-DC Power Adapter interface
OPERATION & CONNECTION
1. Connect one HDMI cable up to 50 feet between Sender (TX) unit
2. Connect one HDMI cable up to 50 feet between Receiver (RX) unit
3. Use a single CAT6/5e, up to 200 feet, to connect the Sender and Receiver
4. Connect the power adapter to Sender and Receiver unit.
SPECIFICATIONS
Max. CAT-6 Length Up to 200 feet
HDMI Input 1080p/1080i/720p/576p/576i/480p/480i
Audio Input
DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-
AC3/DSD
HDMI Output
1080p/1080i/720p/576p/576i/480p/480i
Audio Output
LPCM7.1/DTS/Dolby-AC3/DSD
Max. Bandwidth
225Mhz
Max. Baud Rate
6.75Gbps
Input Video Signal
0.5 ~ 1.5 Volts p-p
Output DDC Signal
≤49.2feet or15m AWG26 HDMI standard cable
Max. Power
Consumption
600mA
Power Adapter
Input: AC 50/60Hz 100V-240V
Output: DC4V/1A (TX/RX)
Operating Temp.
59° ~ 131° F or -15° ~ 55° C
Dimension L x W x H
82 x 44 x 22mm (TX/RX)
Weight
0.41 lb. or 195g
NOTES
Please use these units as instructed to prolong their usefulness.
1. The units should be placed far from damp, high temperature, dusty, erosive, or
oxidative environment.
2. Avoid heavy shaking, hit, or fall.
3. Use original factory power adapter.
4. It is prohibited from touching the power adapter with wet hands.
5. Hold the adapter head and do no pull the power cord when not using the unit.
6. Unplug the power adapter when the units are not to be used for long periods.
7. Do not open the cover to touch the inside parts. There is no serviceable part.

Before powering on, please check the connecting cables carefully. Make sure that
all interfaces are normally connected. The table below is some common to issues
that may arise:
#
Issue
Cause & Ways to Troubleshoot
1
No Power
1. Check the power adapter head is fully and
correctly inserted into the power socket.
2. Check the power switch is on the ON status.
2
No Picture
1. Make sure that the TV is on and has been
connected with the unit.
2. Check if the signal source is on and well
connected.
3. Check the system connection quality.
4. Check if the line is all good quality.
5. Check the cables quality
3
Obscure Picture
1. Try again to connect the cable.
2. Use good quality HDMI cable.