AWNLUX W5900 Instruction sheet

P . 1
Package Contents
Manual Control
Motorized and Crank handle
Bracket Leg Bracket Handle Crank Peg Manual
Bracket Leg Bracket Switch Handle Crank Adjust Stick Peg Manual
Manual
Manual

Installatin instruction
1. The installation must be carried out by qualified persons.
2. Check the installation area of the car body, and confirm that the installation part
has been strengthened. (if not strengthened, you can ask the RV factory to
strengthen it.)
3. The awning is configured with standard bracket. If extra special fixture structure
is needed, can custom on your own needs.
4. Measure and mark the installation points on the vehicle body according to the
awning brackets position sketch below. Make sure all the brackets are in the
same straight line and same installation level.
Awning Width:A
160
Bracket
23 a 160 a 65
126.5
b b
Unit:mm
Bracket Bracket
160
dd
Awning size Number of brackets
Awning Width Extension
2.5m
3.0m
3.5m
2.0m
2.5m
3
3
3
4
4
4
4
4
4.0m 2.5m
4.5m 2.5m
5.0m 2.5m
5.5m 2.5m
6.0m 2.5m
2.5m
ab
(Unit:mm) (Unit:mm)
30
30
50
140
50
50
150
50
1125
1375
1625
1320
1530
1540
2040
2540
Before drilling, make sure that there are no obstacles outside or inside the installation points.
The diagrammatic sketch above only shows three brackets. IF your awning size is bigger
than 4meters, will be configured with 4 brackets. Ensure the distances (d) between the
brackets shall be the same from one bracket to the other bracket. For a safe and stable
installation, we strongly recommend to always use the correct brackets quantity to install the
awning.(as showed in Pic.1).
5. Fix the brackets. Pic.1
Be careful not to over-tighten the lock nuts of the
bracket for purpose of adjusting when fixing the
brackets . And tighten all the nuts after testing.
160mm
148.8mm
48mm 37.5mm 48mm
13.3mm

When the mounting position of awning is not vertical,
please add a spacer between the mounting bracket
and the vehicle body, to ensure that the bracket can
be installed vertically and the awning can be opened
normally.
P . 3
Installatin instruction
Please make sure that
the brackets can just
hold the back-plate
where the the arm
joints are settled(as
shown)and all brackets
are on the same line.
bracket bracket bracket
6. Follow the steps as shown to hang the awning on the brackets and adjust it to
the proper position.
In the bottom of each bracket, there are
two holes .To install the awning only ONE
screw is necessary on both sides of
brackets.
7.Lock the awning with the brackets.
Before fixing the awning locking screw, you must open
the awning until the internal mechanism can be observed,
check the position of the brackets, and use the M5 bolt to
lock the brackets and the awning.(Note:awning must be
opened)
bracket

.
1).Without LED light
a. ①wiring (-) & ②wiring (+) for the power cord, please connect with the car power
supply.
b.③ wiring & ④ wiring are for motor, please connect with motor cable (motor cable
no‘‘+’’,‘‘-’’ differences);
2.Wiring instructions: There are 4 wires at the end of the switch, as shown in the
figure above. Please wire them according to the following wiring steps(Pic.1).
Switch Appearance
just for reference
1. Without LED light:
OPEN: Open the awning
OFF: Awning will stop when button
is released no matter how
far awning extend/retracted.
COLSE: close awning
2. With LED light
OPEN: Open the awning
OFF: 1. Awning will stop when button is released no matter how far awning
extend/retracted
2. Turn off the LED lights
COLSE: close awning
2). With LED light strip
a. ①wiring (-) & ②wiring (+) for the power cord, please connect with the car power
supply.
b. ③wiring & ④wiring are in parallel for controlling the motor and LED light, please
connect with motor and led light cable(motor and LED light cable need parallel
connection);
Blue
White
Black
Red
3.Switch instructions
Switch‘OPEN, OFF,CLOSE’ status as image show：
Pic.1
If your awning is motorized operation, wiring and switch installation are
as follows(Pic.1):
1.Please cut the holes on the car according to the switch bottom shell
measurements(It is recommended to determine the opening size according to
the physical measurement).
60
48
13
26.5
3.5
36
Unit:mm

Usage lnstallations
Fig.1: In order to avoid unnecessary strain on the awning as well as on the vehicle
side, we suggest to take out the legs at about 1 m from the opening.
Fig.2: Grasp the leg near its hinge joint and pull it towards you.
Fig.4:To avoid that the awning will be lifted up by an unexpected gust of wind, it
is necessary to secure the legs to the ground with the provided pegs.In
case of coming storms, we strongly advise you.
Fig.3: Unhook the leg and pull out the leg as show in the figure.After extending
the awning completely, adjust the legs at the proper height.
Fig.5: If you want to fasten the support legs to the vehicle, put the leg-shoes into
the wall brackets.The brackets can be fixed only in reinforced points. The
wall brackets installation position can beadiusted according to the tilt angle
of the awning.
Fig.6: If you need to move your RV when your outdoor activities ends, please
make sure to close the awning completely. (Note:Rewinding the fabric may
cause damages to the fabric, and the awning will not be able to be closed
completely.)
We remind you that our standardawn-
ing is for sun protection ONLY,so
please roll up your awning ifrain,wind
or snow.(Special functionfabric can be
offered as required)
Due to its particular structure, the awning has to be installed on the flat area of the vehicle roof
within a certain height.
This height allows to put the legs
on the ground perfectly.
1.5m
2.0m
2.5m
3.0m
3.5m
4.0m
4.5m
5.0m
5.5m
6.0m
0.70m
0.95m
1.20m
1.45m
1.70m
1.70m
1.70m
1.70m
1.70m
1.70m
1.06m
1.56m
2.06m
2.56m
3.06m
3.06m
3.06m
3.06m
3.06m
3.06m
Height of the legs

P . 6
The support poles are hidden
inside the awning front bar.
Adjust the
support
poles height
as needed.
Support Pole
Pull the support poles a bit out from the
hook,then rotate the poles and keep them
standing on the ground.

Usage lnstallations
Correct
Standard pegs are 4 pieces, if you need to
make your awning more stable, extra pegs
and rope should be bought by yourself.
Installations of the wall brackets
Fabric retracting direction
Fabric winding direction as Pic. shown !
Please retract the fabric
according to the picture
when you close the
awning.
6

P . 8
Trouble Shooting
Your awning has left our warehouse with optimized adjustment.The arms may
lower itself with the time.The necessary re-adjustment should be done as follows;
For arms and fabric
adjustments,
please use ONLY
the shown top bolt !
Turn the nut LEFT/RIGHT for perfect re-positioning.
Make sure that the front profile comes out horizontally in ONE line with the main-
part of the awning (same distance left and right side).

P . 9
When awning can't open or closed completely, you have to make bellow
adjustments by green stick;
Attention
All adjustments must be slightly, such as, first adjust 0.5-1 rounds, then test if it
is working normal, if not still do slight adjustments, until the awning perfectly
working well!
When awning can't completely be open, please
adjust the upper hole in "+" direction.
When awning fabric completely is open, but
motor still working, please adjust it the upper
hole in "-" direction.
When awning fabric completely is closed, but
motor still working, please adjust it the upper
hole in "-" direction.
When awning can't completely be closed, please
adjust the bottom hole in "+" direction.
Trouble Shooting
Inside motor structure

P . 10
Explode Diagram
Manual control Motorized control

W20220530EN