Axent AXENT.ONE User manual

AXENT.ONE / AXENT.ONEPLUS
Art. E81.0500.0001.9
Art. E81.0510.0001.9
CLEANING AND CARE

32
1
2
3
CLEANING INSTRUCTIONS CERAMIC
Under no circumstances should you use harsh or abrasive cleaning substances such as abrasive cream cleansers, scouring powder or
drain cleaner on your ceramic surfaces. Also avoid using steam cleaners and hard, abrasive sponges. Please bear in mind that hair colouring
products can reduce the effectiveness of AXENT Easy Clean.
If you follow this guidance then you should remain satisfied with the performance of AXENT Easy Clean for many years. Recommended
cleaners for sanitary ceramic surfaces with AXENT Easy Clean finish. The use of acidic cleaners with a pH value between 1 and 4 is highly
recommended. Cleaners with a pH value in the neutral range (5 to 8) are not always suitable. We strongly advise against using either weak
or strong alkaline cleaners, i.e. substances with pH values from 9 to 12.
CLEANING INSTRUCTIONS SEAT, LID AND REAR COVER
To continue enjoying your toilet seat and lid for as long as possible, please follow these care tips.
Clean them regularly and promptly to prevent stubborn mineral stains.
The toilet seat and lid can be removed, cleaned and refitted quickly and easily.
Clean surfaces thoroughly with a soft cloth (cotton, not microfibre).
–Use clear, warm water, and a bit of gentle detergent to remove heavier soiling.
–Do not use spray cleaners or microfibre cloths.
–Leave the toilet seat and lid open while the detergent acts on ceramic surfaces.
–Do not use detergents that foam or contain chlorine.
–Wipe the hinges dry.
REMOVING THE TOILET SEAT AND LID
1. Open the seat and lid.
2. Pull the seat and lid vertically upwards out of the fixture at an angle of 90°.
FITTING THE TOILET SEAT AND LID
Insert the toilet seat and lid vertically from above.
1. First push the left-hand bolt of the seat into the hinge.
2. Press and hold the right-hand bolt of the seat.
3. Push the toilet seat and lid down until they click into place in the hinge.
CLEANING HINGES
To ensure your shower toilet functions perfectly, the fixture (bolts and hinges) must
be cleaned regularly.
1. Remove the toilet seat and lid as per the instructions.
2. Clean the hinges of the rear cover with a damp cloth (cotton, not microfibre), then dry.
3. Clean the bolts of the toilet seat and lid with a damp cloth (cotton, not microfibre), then dry.
DESCALING PROGRAMME
The entire water system can be descaled as easily as a coffee machine.
Fill a container with 200ml liquid descaler (preferably Durgol, dilute if necessary as per manu-
facturer’s instructions).
Settings mode is active.
1. Press Flow Rate .
The process starts and the water system is fully emptied.
The spray arm extends without spraying any water.
2. Immerse the spray arm in the container of liquid descaler.
3. The liquid is absorbed.
4. The spray arm moves back to its starting position. The liquid descaler circulates all around
the water system and dissolves any limescale.
5. The liquid descaler is flushed away automatically.
The entire water system is purged six times with fresh water.
This process takes about 6 minutes.
The night light flashes slowly throughout this process.
Do not interrupt the descaling programme once it has started.
CLEANING THE SPRAY ARM
The stainless steel spray arm should be cleaned at regular intervals.
Settings mode is active.
1. Press Spray Arm Position .
2. The spray arm extends without spraying any water.
3. Clean the spray arm with a soft cloth (cotton, not microfibre) or a soft brush, without exer-
ting any pressure.
4. To finish, press Spray Arm Position or Stop .
The spray arm moves back to its starting position.
The seat of the AXENT.ONEPLUS contains electronics, therefore do not immerse
or rinse in water!

AXENT International AG
[e-mail]
www.axentbath.ch
REMOTE CONTROL
CI_Z81.1300.0200_AXENT.ONE_EN_202106
CLEANING THE REMOTE CONTROL
Wipe the remote control with a soft cloth (cotton, not microfibre).
REPLACING THE BATTERIES OF THE REMOTE CONTROL
If the AXENT logo is flashing, the batteries need to be changed soon.
The remote control requires three 1.5 V LR3 / AAA batteries.
1. Open the cover on the back of the remote control.
2. Take out the empty batteries and insert new ones. Ensure they are the right way round.
Every 4 months, the night light flashes red to let you know that all parts in contact with water
need to be descaled.
Once you have run the descaling programme, the night light resets itself to the previously set
mode.
CLEANING RECOMMENDATION
Cleaning interval Cleaning steps
Regularly –Wipe off drops of water with a soft, dry cloth (cotton, not microfibre).
Weekly/monthly –Remove the toilet seat and lid and clean them separately.
–Clean the hinges and bolts of the toilet seat and lid with a damp cloth, then dry.
–Wipe all surfaces and corners thoroughly with a soft, damp cloth (cotton, not microfibre)
and a gentle liquid detergent.
–Inspect the spray arm for signs of scale.
Quarterly –Run the descaling programme.