AXIOMTEK NA346 Series User manual

NA346 Series
Network Appliance
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2020 AXIOMTEK Co., Ltd.
All Rights Reserved
July 2020, Version A2
Printed in Taiwan

iii
Safety Approvals
CE Marking
FCC Class B
FCC Compliance
This equipment has been tested and complies with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or radiate radio frequency
energy and cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.

iv
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the NA346 before making any installation. Be sure both
the system and the external devices are turned OFF. A sudden surge of power could ruin
sensitive components. Make sure the NA346 is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a
trained technician is allowed to do so. Integrated circuits on computer boards are sensitive
to static electricity. To avoid damaging chips from electrostatic discharge, observe the
following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity in your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

v
Table of Contents
Section 1 Introduction...........................................................1
1.1 General Description .................................................................................................... 1
1.2 Features........................................................................................................................... 1
1.3 Specifications ................................................................................................................ 2
1.3.1 Block Diagram................................................................................................... 2
1.3.2 Specifications.................................................................................................... 3
1.4 Dimensions and Outlines.......................................................................................... 5
1.5 I/O Outlets...................................................................................................................... 6
Section 2 Hardware and Installation....................................9
2.1 Check List........................................................................................................................ 9
2.2 Memory Module (SO-DIMM)................................................................................10
2.3 Board Layout ...............................................................................................................11
2.4 Jumper Settings..........................................................................................................13
2.4.1 RTC/CMOS Clear Jumper (JP1 & JP2) ........................................................ 14
2.4.2 LAN Bypass Control Selection Jumper (JP7, JP8, JP10) .............................. 14
2.4.3 TACT SW1 Function Selection Jumper (JP9)............................................... 15
2.5 Connectors...................................................................................................................16
2.5.1 Mini PCIe full & half connector (CN4/CN5) ............................................... 17
2.5.2 LAN Port (LAN1~LAN4)............................................................................. 18
2.5.3 USB3.0 Port0 ~ Port1 Connector (CN9) ..................................................... 18
2.5.4 Nano SIM card slot (CN6) .......................................................................... 18
2.5.5 HDMI (CN8) ............................................................................................... 19
2.5.6 Serial Port1 (For Console) (COM1)............................................................. 19
2.5.7 Serial Port2 (COM2 for Optional)............................................................... 19
Section 3 AMI BIOS Setup Utility .......................................21
3.1 Starting..........................................................................................................................21
3.2 Navigation Keys..........................................................................................................21
3.3 Main Menu...................................................................................................................22
3.4 Advanced Menu .........................................................................................................24
3.5 Chipset Menu..............................................................................................................37
3.6 Security Menu .............................................................................................................39

vi
3.7 Boot Menu....................................................................................................................40
3.8 Save & Exit Menu.......................................................................................................44
Appendix A LAN Bypass Configuration ...............................53
About LAN Bypass..............................................................................................................53
Appendix B WDT Timer for System Reset.............................55
WDT (Watchdog Timer) ....................................................................................................55
Appendix C Warning..............................................................57

NA346 User’s Manual
Introduction 1
Section 1
Introduction
This chapter contains general information and detailed specifications of the NA346 Series
Network Appliance Server. It contains the following sections:
General Description
Features
Specifications
Dimensions and Outlines
I/O Outlets
1.1 General Description
The NA346 is a compact desktop network security hardware platform for VPN, firewall and
other network security applications, which can support Intel® Apollo Lake processor. This
platform supports one DDR3L-1866 SO-DIMM slot with maximum of up to 8GB memory. In the
meantime, the platform also can support four gigabit Ethernet ports which can provide the
best throughput. For storage, it also provides two mSATA SSD drive. This platform can be easily
enabled through application programs to make a user-friendly appliance for customers, and
provide the highest ever performance of encryption and decryption.
1.2 Features
NA346 series supports Intel® Apollo Lake processor, has compact size design' high
compatibility, and low power for network security field application.
Intel® Apollo Lake Processor
Supports up to 8GB DDR3L-1866 SO-DIMM system memory
Supports up to four 10/100/1000 Mbps Ethernet ports
Supports two mini-PCIe slot for Wireless/3G/LTE and mSATA
Supports console redirection to COM port
Supports Windows 10 and Linux operating systems

NA346 User’s Manual
2 Introduction
1.3 Specifications
1.3.1 Block Diagram

NA346 User’s Manual
Introduction 3
1.3.2 Specifications
Model
NA346
SBCs
SBC8A346
Form Factor
Desktop
Chassis
Material
Steel
Chipset
N/A
Processor/Cac
he
Intel® Celeron® N3350 1.1GHz/2C/2M/6W
BIOS
AMI 128Mbits PnP Flash BIOS with function of BIOS redirected to
COM port
System
Memory
1 x DDR3L SO-DIMM socket, up to 8GB none-buffer none-ECC / ECC,
up to1866MHz
Super I/O
Controller: NCT6102D LQFP128 NUVOTON
Detection of CPU temperature, system temperature, power failure
Graphic
Intel® HD Graphics 505 Integrated
Storage
1 x mini-PCIe socket for mSATA (Half Type)
1 x mini-PCIe socket for mSATA (Full Type)
1 x SATA3.0 connector (Reserved layout only, SATA signal co-layout
with Full-size miniPCIe slot)
Ethernet
4 x 1GbE RJ45 (Intel® i211AT)
(One pairs LAN bypass for optional, Eth1 and Eth2)
System I/O
4 x 1GbE RJ45
1 x Console port (RJ45 type, follow Cisco pin define)
2 x USB 3.0 ports
1 x HDMI 1.4b (3840x2160)
1 x Reset button.
1 x GPI button
1 x 4 (POWER ,HDD, Lan bypass LED, GPIO LED)
Board
Connectors
1 x COM2 box header (Reserved for RS232/RS422/RS485)
1 x SIM Socket
1 x SATA 3.0 connector (Reserved only)
Expansion
slot
1 x Half-size miniPCIe slot with SATA/USB signal
1 x Full-size miniPCIe slot with SATA/USB signal (PCIe signal for
optional, PCIeX1 co-layout with Eth4)
Power
12V/5A 36W Adaptor with screw type
PCBA
Dimensions
130 x 113mm
System
Dimensions
33.5mm (1.32”) (H) x 146mm (5.75”) (W) x 118.2mm (4.65”) (D)
Weight (Net/
Gross)
0.616 kg / 1.3 kg
Form Factor
Small Fanless chassis , support Wall-mount kit(option)
Other
4 x hole for Wireless/LTE
Easy to install DDR and storage
Certifications
CE/FCC Class B

NA346 User’s Manual
4 Introduction
OS
Linux kernel
(Ubuntu 15.10/Fedora 23/Yocto 64 bit/Centos6.9&7.3/FreeBSD or
latest version)
Environmenta
l
Operating temperature: 0°C ~ 60°C
Storage temperature: -20°C ~ 70°C
10% ~ 90% non-condensing
NOTE: All specifications and images are subject to change without notice.