Axis T91A61 User manual

INSTALLATION GUIDE
AXIS T91A61 Wall Mount
AXIS T91A62 Parapet Mount
AXIS T91A63 Ceiling Mount
AXIS T91A64 Corner Mount
AXIS T91A67 Pole Mount
ENGLISH DEUTSCH ITALIANO ESPAÑOL
FRAN
Ç
AIS
www.a1securitycameras.com email: [email protected]

About this Document
This document includes instructions for installing the
AXIS T91A Mounting Accessories.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area.
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 3
ENGLISH
AXIS T91A Mounting Accessories
This installation guide provides instructions for installing the wall/parapet/ceiling/corner/pole
mounting accessories for Axis network cameras. For all other aspects of using the Axis network
camera, please see the Installation Guide and User’s Manual, available from www.axis.com
Installation steps
1. Check the package contents against the list below
2. Hardware overview. See page 4
3. Install the hardware:
•
Install the AXIS T91A61 Wall Mount, see page 6
•
Install the AXIS T91A62 Parapet Mount, see page 7
• Install the AXIS T91A63 Ceiling Mount, see page 9
•
Install the AXIS T91A64 Corner Mount, see page 11
•
Install the AXIS T91A67 Pole Mount, see page 12
Package contents
Model Item
AXIS T91A61 Wall Mount Wall bracket
Bracket holder
AXIS T91A62 Parapet Mount Parapet bracket
Bracket holder
AXIS T91A63 Ceiling Mount Ceiling bracket
Bracket holder
AXIS T91A64 Corner Mount Corner bracket (AXIS T91A61 required)
4 M8x22 screws
AXIS T91A67 Pole Mount Pole bracket
Steel straps (steel strap tool not supplied)
Important!
This product must be used in
compliance with local laws and
regulations.
www.a1securitycameras.com email: [email protected]

Page 4 AXIS T91A Series Installation Guide
Hardware overview
Side cover
(remove for cable)
Torx T30 screws (4)
Pendant adapter
Parapet bracket
Side cover
Secure nut
Torx T30 screws (4)
Pendant adapter
(remove for cable)
Ceiling bracket
Side cover
(remove for cable)
Torx T30
Pendant adapter
screws (4)
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 5
ENGLISH
Note:
Some installations may require the supplied pendant adapter to be replaced which is done
by loosening the stop screw and unscrewing the adapter. In this case, refer to the Installa-
tion Guide included with the pendant kit.
Pole bracket
Steel straps
(requires steel strap
Corner mount bracket
Screw hole (top)
Mounted
this way up
Torx T30 screws (3)
Slots for
unit holders (3)
Safety wire
Stop screw
Pendant adapter
Pendant adapter
tool - not supplied)
Holes for
mounting
screws (6)
Metal tabs
for temporary
Bracket holder
support (4)
Locking tab
This way up
(when mounting
on wall)
www.a1securitycameras.com email: [email protected]

Page 6 AXIS T91A Series Installation Guide
Install the Hardware
Install the AXIS T91A61 Wall Mount
1. Refer to Hardware overview, on page 4 for information on the supplied
parts.
2. Route the network cable through or along the wall.
3. Attach the bracket holder in the desired position using screws that are
appropriate for the wall material and the weight of the camera and
bracket.
4. The wall bracket can temporarily be hooked on the bracket holder, in order to easily route the
cable through the bracket:
5. Route the necessary cables through the wall bracket, securing them in the cable holder.
6. Pull the locking tab and unhook the wall bracket from the temporary position.
7. Use the Torx screws to secure the wall bracket to the bracket holder.
8. Refer to the Installation Guide for the network camera for instructions on how to attach the
camera to the bracket.
Tabs
Swing wall bracket
to the side for
temporary support
Slide bracket between the
tabs on the bracket holder
Locking tab
Cable
Cable
holder
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 7
ENGLISH
Install the AXIS T91A62 Parapet Mount
1. Refer to Hardware overview, on page 4 for information on the supplied
parts.
2. Route the network cable through or along the roof.
3. Attach the bracket holder in the desired position on the roof using
screws that are appropriate for the material and the weight of the
camera and bracket. Install the bracket maximum 80 mm (3.2 in.) from
the edge of the roof for the camera’s outer diameter to be aligned with
the edge of the roof. Maximum weight allowed 15 kg (33 lbs).
4. Route the necessary cables through the parapet bracket, securing them
in the cable holder.
Install bracket holder
Cable holder
Cable
from the edge of the roof
Bracket holder
Note : Do not use bracket holder
as a temporary support
with the parapet bracket.
max. 80 mm (3.2 in.)
www.a1securitycameras.com email: [email protected]

Page 8 AXIS T91A Series Installation Guide
5. Use the Torx screws to secure the parapet bracket to the bracket holder.
6. Rotate the bracket and tighten the secure nut to lock the bracket in a sideways position. The
camera can now be installed safely rather than hanging over the edge of the roof. The secure
nut is loose at delivery for this purpose.
7. Refer to the Installation Guide for the network camera for instructions on how to attach the
camera to the bracket.
8. Rotate the bracket into position and tighten the secure nut firmly.
Notes:
• Some installations may require the supplied pendant adapter to be replaced, which is done by
loosening the stop screw and unscrewing the adapter. In this case, refer to the Installation Guide
included with the pendant kit.
Secure nut
Safety wire
Torx T30 screws (3)
Slots for unit holders (3)
Torx T30 screws (4)
Rotate sideways to
install camera
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 9
ENGLISH
Install the AXIS T91A63 Ceiling Mount
1. Refer to Hardware overview, on page 4 and page 5 for information on the
supplied parts.
2. Route the network cable through or along the ceiling.
3. Attach the bracket holder in the desired position in the ceiling using screws
that are appropriate for the ceiling material and the weight of the camera
and bracket. Maximum weight allowed 15kg (33lbs).
4. Route the necessary cables through the ceiling bracket, securing them in the cable holder.
Note : Do not use bracket holder
as a temporary support
with the ceiling bracket.
www.a1securitycameras.com email: [email protected]

Page 10 AXIS T91A Series Installation Guide
5. Use the Torx screws to secure the ceiling bracket to the bracket holder.
6. Refer to the Installation Guide for the network camera for instructions on how to attach the
camera to the bracket.
Torx screws(4)
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 11
ENGLISH
Install the AXIS T91A64 Corner Mount
1. Refer to Hardware overview, on page 4 for information on the supplied
parts.
2. Attach the corner bracket in the desired position using screws that are
appropriate for the wall material and the weight of the camera and
bracket.
3. Attach the bracket holder (not included) to the corner bracket using the
supplied screws.
4. The wall bracket (not included) can temporarily be hooked on the bracket holder, in order to
easily route the cable through the bracket:
Note:
The bracket holder and wall bracket (AXIS T91A61) are required for the installation but
must be purchased separately, see the table in
Package contents, on page 3.
5. Route the necessary cables through the wall bracket, securing them in the cable holder.
6. Press the locking tab and unhook the wall bracket from the temporary position.
7. Use the Torx screws to secure the wall bracket to the bracket holder.
8. Refer to the Installation Guide for the network camera for instructions on how to attach the
camera to the bracket.
Tabs
Swing wall bracket
to the side for
temporary support
Slide bracket between the
tabs on the bracket holder
Locking tab
Wall bracket
Corner bracket
Bracket
holder
CableCable
holder
www.a1securitycameras.com email: [email protected]

Page 12 AXIS T91A Series Installation Guide
Install the AXIS T91A67 Pole Mount
1. Refer to Hardware overview, on page 4 and page 5 for information on
the supplied parts.
2. Route the necessary cables through the bracket, securing them with
the cable holder.
3. Use the supplied steel straps to attach the bracket to the pole and
tighten with a steel strap tool (not supplied).
4. Refer to the Installation Guide for the network camera for instructions on how to attach the
camera to the bracket.
Cable
Cable
holder
Cable
holder
Steel straps
www.a1securitycameras.com email: [email protected]

AXIS T91A Series Installation Guide Page 13
ENGLISH
Technical Data
Bracket holder
AXIS T91A61
Wall Mount
AXIS T91A62
Parapet Mount
AXIS T91A63
Ceiling Mount
AXIS T91A64
Corner Mount
AXIS T91A67
Pole Mount
Size
WxHxD
mm (in.)
140 x 200 x 270
(5.6x8x10.7)
470 x 754 x 138
(18.5 x 29.7 x 5.4)
195 x 750 x 138
(7.7 x 29.5 x 5.4)
345 x 200 x 185
(13.6 x 8 x 7.3)
140 x 200 x 270
(5.6x8x10.7)
Weight g (lbs) 1450 (3.2) 2900 (6.4) 2000 (4.4) 1250 (2.8) 1220 (2.7)
Max. weight
supported
kg (lbs)
15 (33) 15 (33) 15 (33) 15 (33) 15 (33)
Material Aluminum Aluminum Aluminum Aluminum Aluminum
Color code NCS S 1002-B NCS S 1002-B NCS S 1002-B NCS S 1002-B NCS S 1002-B
Mounting
holes diameter
mm (in.)
9 (0.35) 9 (0.35) 9 (0.35) 10 (0.4) -
Pole size
mm (in.)
- - - 80–150 (3–6)
96 mm (3.8 in.)
124 mm (4.9 in.)
118 mm (4.6 in.)
183 mm (7.2 in.)
www.a1securitycameras.com email: [email protected]

www.a1securitycameras.com email: [email protected]

AXIS T91A Guide d'installation Page 15
FRAN
Ç
AIS
Accessoires de montage AXIS T91A
Ce guide d’installation vous explique comment installer les accessoires de montage mural, de
montage d’angle et de montage sur poteau pour les caméras réseau Axis. Pour toute autre
instruction d’utilisation de la caméra réseau Axis, veuillez consulter le guide d’installation et le
manuel de l’utilisateur, disponibles sur le site www.axis.com
Procédure d'installation
1. Vérification du contenu de l’emballage par rapport à la
liste ci-dessous
2. Vue d’ensemble du matériel. Reportez-vous à la page
16.
3. Installation du matériel :
•
Installation du montage mural AXIS T91A61, voir
page 18
•
Installation du montage sur parapet AXIS T91A62, voir page 19
•
Installation de la fixation au plafond AXIS T91A63, voir page 21
• Installation du montage d’angle AXIS T91A64, voir page 23
•
Installation du montage sur poteau AXIS T91A67, voir page 24
Contenu de l’emballage
Modèle Élément
Montage mural AXIS T91A61 Support mural
Dispositif de fixation du support
Montage de parapet AXIS T91A62 Support de parapet
Dispositif de fixation du support
Montage au plafond AXIS T91A63 Support pour installation au plafond
Dispositif de fixation du support
Montage d'angle AXIS T91A64 Support d’angle (AXIS T91A61 requis)
4 vis M8x22
Montage sur poteau AXIS T91A67 Support de montage sur poteau
Bandes en acier (outil de fixation des bandes en acier non fourni)
Important !
Ce produit doit être utilisé
conformément aux lois et
dispositions locales en vigueur.
www.a1securitycameras.com email: [email protected]

Page 16 AXIS T91A Guide d'installation
Description du matériel
Couvercle latéral
(retirer pour passer le câble)
Vis Torx T30 (4)
Adaptateur de suspension
Support de parapet
Couvercle latéral
Écrou de sécurité
Vis Torx T30 (4)
Adaptateur de suspension
(retirer pour passer le câble)
Support pour installation au plafond
Couvercle latéral
(retirer pour
Torx T30
Adaptateur de suspension
vis (4)
passer le câble)
www.a1securitycameras.com email: [email protected]

AXIS T91A Guide d'installation Page 17
FRAN
Ç
AIS
Remarque :
Certaines installations peuvent nécessiter le remplacement de l’adaptateur de suspension.
Pour ce faire, desserrez la vis de butée et dévissez l'adaptateur. Le cas échéant, reportez-
vous au Guide d’installation fourni avec l’adaptateur de suspension.
Support de montage sur poteau
Bandes en acier
(nécessitent un outil de fixation
Support de montage d’angleTrou pour les vis
Monté
dans ce sens
Vis Torx T30 (3)
Logements pour
les supports de rack (3)
Fil de sécurité
Vis de butée
Adaptateur de suspension
Adaptateur
outil : non fourni)
Trous pour les
vis de
montage (6)
Pattes en métal
pour un
Dispositif de fixation du support
support (4)
Patte de blocage
Dans ce sens
(lors du montage
mural)
(partie supérieure)
(vers le haut)
de suspension
(vers le haut)
www.a1securitycameras.com email: [email protected]

Page 18 AXIS T91A Guide d'installation
Installation du Matériel
Installation de Montage mural AXIS T91A61
1. Reportez-vous à la section Description du matériel, à la page 16 pour
obtenir des informations sur les pièces fournies.
2. Acheminez le câble réseau à travers ou le long du mur.
3. Fixez le dispositif de fixation du support dans la position souhaitée en
utilisant des vis qui sont appropriées au matériau mural et au poids de la
caméra et du support.
4. Le support mural peut être temporairement accroché sur le dispositif de fixation du support,
afin d'acheminer facilement le câble dans le support :
5. Faites passer les câbles nécessaires dans le support mural en le fixant dans le dispositif de
support du câble.
6. Tirez la patte de blocage et décrochez le support mural de la position temporaire.
7. Utilisez les vis Torx pour fixer le support mural au dispositif de fixation du support.
8. Reportez-vous au guide d’installation de la caméra réseau pour savoir comment fixer la caméra
au support.
Pattes
Faire pivoter le support mural
vers le côté
pour obtenir un support temporaire
Glisser le support entre
les pattes sur le dispositif de
Patte de blocage
fixation du support
Attache
Attache
du câble
www.a1securitycameras.com email: [email protected]

AXIS T91A Guide d'installation Page 19
FRAN
Ç
AIS
Installation de Montage de parapet AXIS T91A62
1. Reportez-vous à la section Description du matériel, à la page 16 pour
obtenir des informations sur les pièces fournies.
2. Acheminez le câble réseau à travers ou le long du toit.
3. Fixez le dispositif de fixation du support dans la position souhaitée sur
le toit en utilisant des vis qui sont appropriées au matériau mural et au
poids de la caméra et du support. Installez le support à 80 mm
maximum (3.2 po.) du bord du toit pour que le diamètre extérieur de la
caméra s'aligne avec le bord du toit. Poids maximum autorisé 15 kg (33
livres).
4. Faites passer les câbles nécessaires dans le support de parapet en le
fixant dans le dispositif de support du câble.
Installation du dispositif de fixation du support
Dispositif de support du câble
Attache
du bord du toit
Dispositif de fixation du support
Remarque : ne pas utiliser le dispositif de
comme support temporaire
avec le support de parapet.
80 mm max. (3,2 po.)
fixation du support
www.a1securitycameras.com email: [email protected]

Page 20 AXIS T91A Guide d'installation
5. Utilisez les vis Torx pour fixer le support du parapet au dispositif de fixation du support.
6. Faites tourner le support et serrez l'écrou de sécurité pour bloquer le support dans une position
latérale. La caméra peut maintenant être installée en toute sécurité au lieu d'être suspendue sur
le bord du toit. C'est pourquoi l'écrou de sécurité est desserré à la livraison.
7. Reportez-vous au guide d’installation de la caméra réseau pour savoir comment fixer la caméra
au support.
8. Faites tourner le support dans la position et serrez bien l'écrou de sécurité.
Remarques :
• Certaines installations peuvent nécessiter le remplacement de l’adaptateur de suspension. Pour ce
faire, desserrez la vis de butée et dévissez l'adaptateur. Le cas échéant, reportez-vous au Guide
d’installation fourni avec l’adaptateur de suspension.
Écrou de sécurité
Fil de sécurité
Vis Torx T30 (3)
Supports de rack (3)
Vis Torx T30 (4)
Faites tourner latéralement pour
installer la caméra
www.a1securitycameras.com email: [email protected]