Axor Citterio User manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ assembly instructions 03
AXOR Citterio
39835007

02
安装 (参见第页 04)
问题 原因 补救
⁄龙头不灵活 ⁄ 阀芯损坏，结垢 ⁄ 更换阀芯
⁄龙头滴水 ⁄ 阀芯损坏 ⁄ 更换阀芯
⁄水从螺纹底座中流出 ⁄ 连接软管没有完全旋入基体 ⁄ 用手拧紧连接软管
⁄ 连接软管的O形环损坏 ⁄ 更换O形环
⁄热水温度过低 ⁄ 温度限制器设置错误 ⁄ 设置温度限制器
备用零件 (参见第页 10)
选装附件 (不在供货范围内)
操作扳手 #95910000 (参见第页 10)
流量示意图 (参见第页 09)
 普通水流
 花洒
大小 (参见第页 09)
保养 (参见第页 07)
单向阀必须在符合国家或当地的法律的情况下按照DIN EN 1717定期
检查（至少一年一次）。
清洗 (参见第页 07 并附有小手册)
如果水流减少，清洁位于花洒头和软管之间的过滤网。
操作 (参见第页 07)
⁄ 汉斯格雅建议，清晨或在水流长时间停滞后，前半升水不作饮用
水使用。
⁄ 水嘴旋转不可超过360º，否则会导致软管受损。
调节 (参见第页 06)
热水温度调节。如果使用即热式喷头，则不建议安装热水阀门。
请勿使用含有乙酸的硅胶！
符号说明
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
冷热水管间过大的压力差必须予以平衡。
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后将不认可运输损害或表面
损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和检查。
⁄ 请遵守当地国家现行的安装规定。
技术参数
工作压强： 最大 1 MPa
推荐工作压强： 0,1 – 0,5 MPa
测试压强： 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 70°C
推荐热水温度： 65°C
热力消毒: 最大 70°C ⁄ 4 分钟
该产品专为饮用水设计！
ZH

03
ASSEMBLY (see page 04)
FAULT CAUSE REMEDY
⁄ Mixer stiff ⁄ Cartridge defective, calcified ⁄ Exchange cartridge
⁄ Mixer dripping ⁄ Cartridge defective ⁄ Exchange cartridge
⁄ Water escaping at the threaded base ⁄ connection hoses not completely screwed into basic body ⁄ Tighten connection hoses by hand
⁄ O-ring at the connection hose defective. ⁄ Exchange O-ring
⁄ Hot water temperature too low ⁄ Hot water limiter incorrectly set ⁄ Set hot water limiter
SPARE PARTS (see page 10)
SPECIAL ACCESSORIES (order as an extra)
service tool #95910000 (see page 10)
FLOW DIAGRAM (see page 09)
 Normal spray
 Regular
DIMENSIONS (see page 09)
MAINTENANCE (see page 07)
The check valves must be checked regularly according to DIN EN 1717 in
accordance with national or regional regulations (at least once a year).
CLEANING (see page 07 and enclosed brochure)
If the waterflow drops, clean the filter located between hose and handspray.
OPERATION (see page 07)
⁄ Hansgrohe recommends not to use as drinking water the first half liter of
water drawn in the morning or after a prolonged period of non-use.
⁄ Do not rotate the spout further than 360º or damage to the hose will
result.
ADJUSTMENT (see page 06)
To adjust the hot water limiter. Using a hot water limiter in combination with a
continuous flow water heater is not recommended.
Do not use silicone containing acetic acid!
SYMBOL DESCRIPTION
SAFETY NOTES
Gloves should be worn during installation to prevent crushing and cutting injuries.
The hot and cold supplies must be of equal pressures.
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and tested as per the applicable
standards.
⁄ The plumbing codes applicable in the respective countries must be observed.
TECHNICAL DATA
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 – 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C ⁄ 4 min
The product is exclusively designed for drinking water!
EN

04
150°
24 x 15°
75°
45°
45°
75°
105°
105°
150°
110°
6a
6b
SW 10 mm
SW 24 mm
(4 Nm)
max. 35 mm
max. 60 mm
(3 Nm)
1b 2
3 4 5
6a
1a
Montage

05
6b
24 x 15°
110°
10
CLICK
7 8 9
10 11 12
110°
55°
25°
55°
85°
85°
25°
Montage

06
SW 3 mm
36°C
38°C
43°C
60°C
55°C
50°C
4 x
SW 3 mm
(5 Nm)
(1 Nm)
> 2 min
Nr. 10476220
Armaturenfett
Grease
13 14 15
2
13
456
60 °C 10 °C 0,3 MPA
1.
2.
1.
2.
Montage Justierung

07
开 ⁄ open 开 ⁄ open 热 ⁄ hot
冷 ⁄ cold关 ⁄ close
1 2
21
1.
2.
BedienungBedienung WartungReinigung

08
CLEANING RECOMMENDATION FOR HANSGROHE
PRODUCTS
Today, modern sanitary and kitchen tapware, showers, accessories, washstands, tubs
and radiators consist of very different materials to comply with the needs of the market
with regard to design and functionality.
To avoid damage and reclamations, it is necessary to consider certain criteria when
cleaning.
WITH REGARD TO CARING FOR THE HANSGROHE
PRODUCTS, THE FOLLOWING MUST IN PRINCIPLE BE
HEEDED:
⁄ Only use cleaning material which is explicitly provided for this type of application.
⁄ Never use cleaning materials, which contain hydrochloric acid, formic acid, chlorine
pale lye or acetic acid, as they cause considerable damage.
⁄ Phosphorus acidic cleaners are only conditionally applicable.
⁄ Mixing cleaning agents is not permitted, generally.
⁄ Never use cleaning materials or appliances with an abrasive effect, such as
unsuitable cleaning powders, sponge pads or micro fibre cloths.
⁄ The instructions of the cleaning agent manufacturers have to be followed absolutely.
⁄ Cleaning has to be carried out with a specified cleaner dosage, contact time,
object-related and adapted to the needs.
⁄ The building up of calcifications has to be removed by cleaning regulary.
⁄ When using spray cleaners, spray the cleaning solution onto a soft cloth or sponge,
never directly onto the Hansgrohe products, as the atomised spray could enter
openings and gaps in the Hansgrohe products and cause damage.
⁄ After cleaning rinse thoroughly with clean water to remove any cleaner residue.
⁄ The use of steam cleaners is not permitted. The high temperatures can damage the
products.
IMPORTANT
Residues of toiletries such as liquid soaps, shampoos and shower gels, hair dyes,
perfumes, aftershave and nail varnish can also cause damage.
Here too: Carefully rinse with water after use to remove residues.
Likewise, do not store any cleaning agents or chemicals under the products, for
example in a vanity unit, as the vapours may damage the products.
The damage of already damaged surfaces will deteriorate under the effect of the
cleansers.
COMPONENTS WITH DAMAGED SURFACES MUST BE EXCHANGED,
OTHERWISE THERE COULD BE AN INJURY DANGER.
Damage caused by improper treatment will not be covered by our guarantee.
QUICKCLEAN
The QuickClean cleaning function only needs a small manual rub over to remove the
lime scale from the spray channels.
WARRANTY
Hansgrohe guarantees to the consumer that this product is free of production faults. If
evertheless any defect is detected within 5 years from date of purchase, Hansgrohe
will remedy this defect free of charge. You will find the conditions and details of this
guarantee at www.hansgrohe-int.com⁄guarantee. Please contact your contracting party
to claim your rights under this guarantee. This guarantee does not affect the customer‘s
rights under the respective national legislation.
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗台、浴盆和加热器采用的制造
材料非常迥异，以适应产品外形设计和使用功能的市场需求。
为了避免产品损坏和由此引发的投诉及争议，必须在使用和清洁产品时遵循有
关规程。
在保养汉斯格雅产品时，原则上必须注意：
⁄ 只能使用那些有明确注明是适用于本产品的清洁剂。
⁄ 不允许使用含有盐酸、蚁酸、氯漂或醋酸的清洁剂，因为这些清洁剂会给产
品表面造成严重的损伤。
⁄ 含磷酸的清洁剂必须在特定条件下使用。
⁄ 不允许将两种以上清洁剂混合使用。
⁄ 不允许使用具有研磨作用的清洁工具和设备，如不适合的清洁粉末、海绵垫
或超细麦克布。
⁄ 必须严格遵守清洁剂生产厂商的使用说明。
⁄ 严格遵守清洁剂的用量和作用时间，决不允许清洁剂的作用时间长于规定
值。
⁄ 定期的清洁以预防水垢。
⁄ 不允许将清洁剂直接喷射到汉斯格雅产品上，因为喷雾会进入汉斯格雅产品
的开口部分和缝隙中而造成损害。首先将清洁剂喷在软布上，再用软布进行
清洁。
⁄ 清洁之后必须用足够的清水冲洗，以彻底去除残留的吸附物（清洁剂）。
⁄ 不允许使用蒸汽清洗机，高温会损害产品。
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、指甲油的残留也会对产品造
成损伤。
此处：使用后要小心地用清水将剩余物冲洗干净。
同样在产品下方不得存放洗涤剂和化学药品，例如不可放在用于洗脸盆的梳洗
柜中否则挥发气体将损坏产品。
在已经损伤的表面继续使用清洁剂会给表面造成更大的损伤。
表面损坏的部件必须更换，否则会有受伤的危险。
不按规定进行清洁而造成的任何损坏不在本公司产品保修范围之内。
QUICKCLEAN
有了QuickClean，手工清洁功能，要去掉喷头上的水垢，只需简单地搓除即可。
担保
Hansgrohe 向用户保证，该产品无制造 缺陷。如果自购买之日起五年内出
现缺 陷，Hansgrohe 将免费排除。 保证条件和详 情见 www.hansgrohe-int.
com⁄guarantee。 在提 出保修的权利时请联系您的合同方。本保证 不涉及有关国
家法律规定的消费权
QUICK
CLEAN
Reinigung

09
1
2
AXOR Citterio
39835007
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912151821242730
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
1
2
AXOR Citterio
39835007
Ø 34
G1/2
Maße / DurchflussdiagrammMaße Maße ⁄ Durchflussdiagramm

10
97735000
95926000
95909000
(M22x1 -
15 l⁄min)
98127000
(11x 2)
95908000
96737000
98231000
(18x1,5)
98140000
(20x1)
95910000
(110°⁄150°)
98365000
98211000
(21x2,5)
95561000
(600 mm)
97827000
(8x1, 75)
95507000
(1,5 m)
98749000
97523000
95049000
97548000
98551000
95581000
97489000
(900 mm)
98422000
(7x1,5)
AXOR Citterio
39835007
39891000
96762000
98603000
(M6x10)
97827000
(8x1, 75)
97209000
92115000
(37x2)
92730000
95008000
ServiceteileServiceteile Serviceschlüssel

11

08/2017 9. 0 5 8 8 7. 5 2
AXOR ⁄ Hansgrohe SE
Auestraße 5–9
77761 Schiltach
Deutschland
[e-mail]
axor-design.com