Azden Moto ID User manual
MOTOiD
2.4GHz Digital Wireless Headphones System
2.4GHz デジタルワイヤレスヘッドホンシステム
Operation Manual
取扱説明書
Thank you for choosing products of Azden.
Before start using this product, you should fi rst thoroughly read this manual.
This manual should be kept for future reference.
この度はアツデンの製品をお買い上げ頂き、誠にありがとうございます。
ご使用になる前に、この取扱説明書を必ずお読み下さい。
お読みになった後は、後日お役に立つことも有りますので、大切に保管して下さい。
1
English
Safety precautions
CAUTION
WARNING
DANGER
CAUTION
please comply
■ The marks below mean as follows:
(the followings are just a part of examples of marks)
The following descriptions, indications, precautions and warnings should be observed
strictly to prevent the operators and other personnel from injury and / or damage to
property.
■The symbols below describe the level of injuries or damages as a result of neglecting
the safety rules
This symbol indicates that there is a possibility of death or severe injury.
This symbol indicates the behaviors regarded as illegal.
This symbol shows that there is a possibility of injury or physical damage.
This symbol means “Be careful” items that must be observed.
This symbol means “Prohibited” that should not be done.
This symbol means “Enforced” that which must always be done.
Use the specied types of battery only. Do not mix the used batteries and new batteries. Burst or
leakage of batteries may cause injury or re.
Avoid location with abnormally high temperature.
- It may deteriorate the surface and component of the product and may cause its failure.
- Avoid location close to heating device such as a stove.
Do not place or store in a location subject to dropping rain or water.
- It may deteriorate the surface and component of the product and may cause its failure.
- Invasion of water or foreign substance may cause re or electrication.
Insertion of batteries into the product shall follow the marking on the product, paying attention to
pole marking (plus [+] and minus [-]).
Wrong pole orientation may cause injury, re or contaminating circumstance due to burst or leak-
age of batteries.
Please remove batteries from the product if it is not in use for a long period.
It may cause injury, re or contaminating circumstance due to leakage of batteries.
In case of leakage, please wipe out battery uid on the battery case before inserting new batter-
ies. In case of contact of leaked uid to a body part, thoroughly ush with fresh water.
2
WARNING
DANGER
2.4GHz products
Do not disassemble or modify the equipment.
- It may cause failure of the equipment, and invasion of metal object may cause re or burn.
Keep away from a reach of infants or children.
Do not apply a strong shock.
Keep away from contact with water.
Keep away from contact with foreign substances (ammable material, metal, liquid).
- It may cause electrication, burn, failure or re.
Avoid usage, abandoning or storage in the following locations.
- Inside a car under a hot and strong sunshine.
- Close to a heat source such as a stove.
- Location with a direct sunlight, location with hot and humid environment.
Do not use this product in the vicinity of medical facility and medical equipment.
Do not use this product in aircraft.
Do not use this product in the vicinity of an automated controlled equipment such as an auto-
mated door and a re alarm.
- Inuence of the radio wave may cause malfunction of the equipment, and may cause an ac-
cident.
Refrain from the usage if you noticed abnormality.
- In case you notice abnormal noise, smoke, smell, heat or damage, please stop usage imme-
diately and request repair to your dealer or to us.
Refrain from usage in case you feel any abnormality in your skin.
Make sure to use attached cable for re-charging.
Never use the equipment while you are driving any vehicle such as automobiles, motor cycles or
bicycles.
-It is illegal and may cause trac accident.
Battery
Do not throw into re, heat, disassemble or modify batteries. Do not apply a strong shock.
- It may cause burst, ignition, heat-up, leakage and breakage.
In case of leakage from battery
- In case of contact of the battery uid with your eye, thoroughly ush with a fresh water such
as running tap water and then ask for appropriate medical treatment.
This product (radio) uses 2.4GHz wave band, and employs FH-SS method for modulation with an
interference distance within 80m.
2.4GHz radio frequency regulation dier depends on countries.
This products fully support Japan regulation.
Other country regulation you need to check locally in each country.
English
3
Battery ( Lithium-polymer )
Precautions
Package contents ( Headphone / Transmitter / Accessories )
Always turn o the switch after using the equipment.
Most of uid leakage is cause by excessive consumption of battery due to forgetting turning o
the switch.
Battery is a consumable parts that deteriorate even under the normal usage. Battery consump-
tion is a property of the battery, which is not a failure. Repair of built-in batteries is not free of
charge even within the warranty period. Lengthened storage of this product without using it may
deteriorate battery performance.
Repeating discharging/re-charging the battery may regain the performance.
The time for continuous use may be shortened under circumstance with low ambient tempera-
ture.
Lithium-polymer rechargeable battery is a recyclable resource.
● Lengthened wearing of the headphone or excessively large volume may cause adverse
inuence to your hearing.
● Avoid usage and storage in hot, humid and dusty circumstance. Do not store at a lo-
cation within a reach of children below three (3) years old.
● Do not drop or hit hard due to possible damage to the internal circuit.
● Lengthened period of storage under heavy load or pressure may cause deformation.
● Any dirt should be wiped with soft cloth. Do not wipe with any chemical solution.
● Dirt or dust on a plug may cause adverse impact to the sound quality, which should be
wiped with soft cloth.
● In case of being wet, please refrain from usage. Wait until complete dry-up.
● Lengthening usage of the ear-pad may deteriorate it.
◆ Wireless headphones ( receiver )
- Stereo 3.5mm code with plug / 1.5m ( for wired usage )
- AAA alkaline battery
◆ Transmitter
- Plug adapter / from stereo 3.5 mm plug to stereo 6.3 mm plug
- Micro USB cable
- RCA plug adapter / from stereo 3.5 mm jack to RCA
- Stereo 3.5mm code with plug ( for transmitter )
◆ Operation manual / Warranty certicate : This manual
◆ Carrying case
: 1 set
: 1 pc.
: 2 pcs.
: 1 set
: 1 pc.
: 1 pc.
: 1 pc.
: 1 pc.
: 1 pc.
: 1 pc.
4
Features
◆ 2.4GHz Digital wireless communication
More free and more personalized enjoyment of music without any annoying cabling
◆ USB / Analog (φ3.5 & φ6.3)
Compatible to digital / analog audio input and various types of audio players.
The audio ports include a φ3.5 plug pin or a φ6.3 mm plug pin.
◆ Reception is available in approximately 30 m of direct distance without obstruction (at HI
setting ) Enjoy music while freely walking around in the room.
* Depending on radio wave environment.
◆ 40 mm large size speaker unit
Heavy and clear bass range, and clear and bright midrange.
True playback of original sound is realized with an eect of straight treble.
◆ Battery life ( headphone )
Approximately fteen (15) hours - (Two (2) - AAA alkaline batteries)
◆ Transmitter employing rechargeable battery
It lasts for about twenty-eight (28) hours, convenient for outdoor use. ( at LO setting )
◆ Micro USB adaptor
Recharging terminal for built-in battery. It is connected to USB port of PCs with attached Mi-
cro USB cable. It is also used as an input adaptor for USB audio devices.
◆ Auto sleep feature
Approximately ten (10) minutes duration with the sound source terminated automatically
turns the power supply o for the headphone and transmitter.
◆ Use with cord with plug
You can use it as a wired headphone without any concern for battery by connecting the ac-
cessory dedicated cord.
◆ Pairing feature
This product allows you to connect multiple headphones to a single transmitter.
You can enjoy sharing the same music simultaneously with headphones within a reach of
radio wave with this feature. ( Additional purchase of headphones is required )
◆ Jump-in feature ( infrared ray communication )
Infrared ray communication feature allows you easy pairing between headphones.
( Additional purchase of headphones is required )
English
5
Component
Name and function of components
● Transmitter
(1) Transmitting power switching switch (LO/HI) : Output setting is switched.
LO : Energy saving mode (distance approximately 10 m )
HI : Long range mode (distance approximately 30 m )
* This distance is subject to be straight without any obstruction. It depends on the radio wave environ-
ment.
(2) Charge indicator ( orange LED ) : Illuminated during charging. It is turned o when charg-
ing is completed.
(3) Power button: Pressing and holding the button (approximately two (2) seconds) allows
you to turn ON/OFF the power supply.
(4) USB connector: For micro USB cable connection. It is used for charging and audio input.
(5) ID button: Used for pairing.
(6) Line INPUT: Audio is input by connecting code with 3.5 mm plug.
* The maximum input level of audio is 2.0 [VP-P].
(7) Power Status indicator supply ( blue / red LED ) : It is illuminated/ashes when the power
supply is ON. It is in blue normally, and turned to red when remaining battery capacity be-
comes low. It is constantly illuminated while an audio is input, and ashes slowly when the
audio is not input. It rapidly ashes during pairing operation.
(1) Transmitting power switching switch (LO/HI)
(5) ID button
(2) Charge indicator
(7) Power Status indicator
(4) USB Connector
(2) Power button
(6) Line INPUT
6
● Wireless headphones (receiver)
(1) Ear pad (left)
(2) Power button: Pressing and holding the button (approximately two (2) seconds) allows
you to turn ON/OFF. It mutes sound while the button is pressed.
(3) Battery cover: Batteries (two (2) AAA batteries) are installed and removed by removing
the battery cover. ( slightly turn to unti-clockwise direction and pick up.)
(4) Power Status indicator (blue/red LED): It is illuminated/ashes when the power supply is
ON. It is in blue normally, and turned to red when remaining battery capacity becomes low.
It is illuminated constantly during audio playback, and it slowly flashes when no radio
wave is received or audio is not input. It rapidly ashes during pairing operation.
(5) Ear pad (right)
(6) PAIR button: Used for pairing.
(7) Volume control: Adjusting sound level.
(8) IR LINK button: For Jump-in feature. It is used during infrared ray communication.
(9) Infrared ray communication window: It is an optical transmitter/receiver for infrared ray
communication.
(10) φ3.5 mm stereo mini jack: The dedicated code is connected in case of using as a wired
headphone.
(9) Infrared ray communication window
(6) Pair button
(5) Ear pad ( Right )
(1) Ear pad ( Left )
(10) φ3.5 mm stereo mini jack
(3) Battery cover
(2) Power button
(4) Power Status indicator
(8) IR LINK button
(7) Volume control
English
Component
7
How to install battery (wireless headphones)
● Installation of battery
1. The battery cover is removed by turning left,
2. Two (2) - AAA alkaline batteries are inserted. (Please pay attention to direction of batteries)
3. The battery cover is attached by rotating the cover in clockwise direction,
(Turn it until it is locked)
When the battery capacity becomes low
Power Status indicator is illuminated in red.
It is also notied by beeping sound (short repeating "puh"s).
It is automatically turned o when the battery capacity has run out.
Turn left
Turn right (until locked)
Close
Open Insert batteries
Attention
Direction of the battery cover
Attention
Direction of the battery cover
Status indicator of Power supply
Battery Cover
Battery Cover
(Housing: left side)
Attention
Direction of AAA alkaline batteries
Up
STEP1 STEP2
STEP3
8
How to recharge (transmitters)
● This product uses Lithium-polymer re-chargeable battery.
Make sure to re-charge prior to start using it.
1. Attached Micro USB cable is connected to the transmitter, and then it is connected to the
USB port of PCs.
2. LED of the transmitter ashes (orange) to start charging.
* The LED turns o when charging is completed.
AC adapter is not included in the package. Please purchase it separately.
Refer to the specication for connection.
When the battery capacity becomes low
Power Status indicator is illuminated in red.
Power supply is automatically turned o when the battery capacity has run out.
Please start charging when the indicator is illuminated in red.
Usable time
The following time period is available to use depending on the setting of transmitting power
switching switch.
For HI: Approximately fourteen (14) hours
For LO: Approximately twenty-eight (28) hours
* It depends on condition to use
Charging time
It completes charging in approximately six (6) hours.
The LED turns o when charging is completed.
* Time for charging depends on remaining battery capacity.
Remaining battery capacity shortens the time to complete charging.
PC
AC outlet
LED
Status indicator of Battery
1
2
USB Port
Micro USB Port
Micro USB Cable
To USB port
AC adapter ( 5V 500mA )
* AC adapter is not included in the package.
Please purchase it separately.
Refer to the specication for connection.
Transmitter
English
9
How to use
● Pairing of the transmitter and wireless headphone is completed in the factory before shipping.
Operation shall follow the description below.
a. Connect the transmitter and the player with the connection cable and then check that the
player is playing back music.
b. Pressing the power button of the transmitter lightly for about two (2) seconds turns the
power on to illuminate the Power Status indicator.
(It ashes when it is not paying back)
c. Pressing the power button of the wireless headphone lightly for about two (2) seconds
turns the power on to illuminate the Power Status indicator of the wireless headphone
side.
Stereo 3.5mm
Cord with plug
Stereo 3.5mm
Audio input jack to stereo 3.5mm jack
RCA plug adapter
Audio input terminal of other AV
Television
Other AV device
such as a player
Other AV device
such as portable audio
Red
White
Power button
Power button
Housing Right
Transmitter
Headphone
Power Status indicator
Power Status indicator
10
● Pairing
* It is operated with the power of both devices
* Operate with Status indicator of power illuminates in blue.
There are two types of methods for pairing.
1. For pairing headphone using transmitter (standard procedure)
STEP1
Pressing the ID button of the transmitter for about three (3) seconds with a harp edge
such as the point of a pen ashes the Power supply/Status indicator rapidly for about
ten (10) seconds.
STEP2
Pressing the PAIR button of the head phone for three (3) seconds or more ashes the
Status indicator of power rapidly for about ten (10) seconds. Also, you will hear a beep-
ing sound (long "puh") from the headphone.
STEP3
Setting both devices in rapid ashing (approximately ten (10) seconds) state runs the
pairing. Completion will illuminate the Power Status indicator of the headphone for
about three (3) seconds. In addition, you will hear a beeping sound (long "puh") once to
enable audible checking.
* You can start either from "STEP1" or "STEP2".
* Multiple headphones can be paired simultaneously while the transmitter is flashing for
ten (10) seconds.
Transmitter Headphone
Power Status indicator Left Housing
Power Status indicator
ID button
PAIR button
POWER button
English
How to use
11
2. For adding wireless headphone using jump-in feature (infrared ray communication)
For pairing the second or more headphones, the infrared ray communication feature in-
stalled in the headphone allows you easy pairing between headphones without using the
transmitter.
This feature allows a new user with a headphone to easily joins (jump-in) to the existing
group enjoying music.
STEP1
The infrared ray communication windows of a headphone to be newly paired and that of
a headphone already paired are faced each other within distance of 15 cm.
STEP2
Clicking once IR LINK button of the headphone to be paired illuminates the communica-
tion window in blue. (slow ashing)
* Do not press IR LINK button of the one that is already paired at this moment.
STEP3
Inside of the communication window of the headphone to be paired enters state to il-
luminate for three (3) seconds when the pairing is completed. (pairing completed)
* No illumination indicates that the communication is failed. Check the procedure to
retry. Pressing and holding the IR LINK button of the side that is already paired but is
pressed inadvertently may restore the previous state. (the previous state may not be
restored after turning o the power)
* Multiple headphones can be paired simultaneously while the transmitter is ashing for
ten (10) seconds.
Housing Right
Housing Right
Within 15cm
Infrared ray communication window
How to useHow to use
12
PC LED
Power Status indicator
USB Port
Micro USB Port
Micro USB Cable
Transmitter
● In case of connecting to PC
Connecting the transmitter to USB port of PC automatically installs the drive.
It is compatible to the following OSs.
Windows XP / Windows Vista / Windows 7 / Windows 8 / Windows 10
Mac OS X (v10.7 or later)
* Either one of the OS listed above is required to be installed when the PC is shipped from
the factory.
* Please check the operation setting of PC in case it is not automatically recognized.
* Custom made PC, personally upgraded OS or environment under a multi booting are not
guaranteed for its operation.
● In case of using with wire without using wireless feature
Attached dedicated stereo 1.5 m cord is inserted to the jack of the headphone, the cord is
turned for a half turn to lock it, check that the wireless feature is canceled, and then use it
by wired connection.
* Volume control feature is not available on headphone side when the attached cord is in
use. The volume is to be adjusted on the connected AV device.
In this state, capacity of AAA batteries used in the headphone is not consumed.
STEP1
Shape of headphone
jack hole
Plug shape
Turn and lock cord
Connection to other
AV device such as
a portable audio
STEP2
Housing Right
English
How to use
13
Troubleshooting (failure is suspected)
● Sound volume is too low/No sound
a. Check illumination of Power/ Status indicator.
b. Adjust the headphone volume.
c. Check if playing back of the source player is running, or is set to sucient volume.
● Too much noise
a. Pressing ID button of the transmitter allows selection of the pattern from four types of
hopping patterns (frequency combination pattern)
This may reduce the external noise.
b. Adjust the headphone volume.
c. Check if playing back of the source player is running, or is set to sucient volume.
● No illumination of Power/ Status indicator of headphone
a. Try restart after turning o the power supply once.
b. Replace batteries. (Two (2) - AAA batteries)
● No illumination of Power/ Status indicator of transmitter
a. Try restart after turning o the power supply once.
b. Try recharging by connecting attached Micro USB cable.
● Unable to connect wireless headphone (ashing)
a. Move the headphone closer to the wireless transmitter.
b. Check if the transmitter and player are securely connected, and if the player is playing
back.
c. Try restart after turning o the power supply of headphone once.
d. Try pairing of transmitter and headphone once again.
● Others
a. Stopping playback of the player that is a source of sound in the state in which pairing is
completed and available to use causes the Power supply/Status indicator to ash slowly.
Playing back again stops the ashing to enter the state with the light illuminated. Pressing
the power button of the transmitter lightly for about two (2) seconds turns the power on to
illuminate the Power Status indicator.
(It ashes when it is not paying back)
b. Turning o the power supply after the pairing does not cancel the pairing.
c. Please turn o both power supplies of the transmitted and the headphone.
d. In case of connecting both of the USB cable and the cord with the stereo 3.5 mm plug
(analog) to the transmitter, analog side has a priority for the audio input. In this case the
USB functions as a charging input.
How to use
14
Specication
Wireless headphones (receiver)
Type
Driver unit
Magnet
Playback frequency band
Weight
Transmitter
Communication frequency band
Communication distance
USB input (charging)
* Aforementioned specification is subject to change without notice for improvement and
other purpose.
Azden Corporation
http//:www.azden.co.jp
e-mail:[email protected]
Address:1-12-17, Kamirenjyaku, Mitaka-shi, Tokyo 181-8533 Japan
Sales department TEL +81-422-55-5115, FAX +81-422-55-0131
: Sealed dynamic type
: Diameter 40 mm
: Neodymium Magnet
: 20 - 20,000Hz
: Approximately 210 g (excluding cord and AAA batteries)
: 2.4GHz band
: Maximum approximately 30 m (line of sight)
: 5V 500 mA
Wireless headphones breakdown diagram
English
15
Warranty Certicate
Warranty Provision
1. Any failure of the product under the normal usage condition during the warranty period may be re-
paired for free of charge.
2. The following cases may be subject to be a charged repair even within the warranty period.
(1) Failure caused by ood, lightning, abnormal voltage and other natural disasters.
(2) Accident and damage due to transportation or drop after the purchase.
(3) In case the purchased evidence such as the invoice when purchasing and below certicate
document is not fulled in and not attached when claiming.
(4) Absence of entry of specied items, or change of entry may be subject to exempt the provision
of repair.
3. Any improper repair or modication may be subject to exempt the provision of repair.
4. 2.4GHz radio frequency regulation dier depends on countries. This products fully support Japan
regulation. Other country regulation you need to check locally in each country.
The claim for radio frequency is out of our control. Any change for supported countries will be an-
nounced through our web page in the future.
5. This repair is only supported in Azden Japan service center until other countries’ warranty service
is announced.
6. This warranty does not cover any shipping cost for repairs. Your understanding is really appreciate
in advance.
This manual may ensure a repair free of charge based on the aforementioned warranty provisions.
Following information need to receive your warranty request.
Model Name Product serial number (if possible)
Customer
Tel
Warranty period
Dealer or shop name for sales to you :
One (1) year after date of purchase
Day Month Year
e-mail
Address
Date of purchase
Name
MOTOiD
Printed in Japan 035-32799-03
Table of contents
Other Azden Headphones manuals
