B-Tech Mountlogic BT8222 Instruction Manual

B-TECH AUDIO VIDEO MOUNTS
www.btechavmounts.com
CONTENTS
INSTALLATION TOOLS REQUIRED
FEATURES
BT8222
SINGLE ARM FLAT SCREEN MOUNT
FOR EXTRA LARGE SCREENS
INSTALLATION GUIDE & PARTS LIST
This Pack Contains 1 Mount
Installation Safety Notes.....................................................................................................................2
Parts List.............................................................................................................................................4
Installation Instructions.......................................................................................................................6
Product Dimensions..........................................................................................................................18
B-Tech Contact Details.....................................................................................................................20
PLEASE KEEP THIS FOR FUTURE REFERENCE
12mm (15/32") masonry bit
or 8mm (5/16") wood bit
●Designed for flat screens up to 65” (165cm) / 60kg (132lbs)
●Fits screens with VESA & Non-VESA mounting patterns
up to 790mm (31.1”) x 500mm (20”)
●Easy tilt adjustment +15°
●Features two swivel points:
180° at wall and 120° at interface
●Suitable for concrete / brick or stud walls up to 16”
●Simple ‘hook-on’ installation with all
mounting hardware included
Crosshead
screwdriver
Drill Pencil Stud finder
(optional)
17mm (17/26")
spanner or socket
INSTALLATION MAY
REQUIRE 2 PEOPLE

2
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This wall mount is intended for use only with the maximum weights
indicated. Use with flat screen heavier than the maximum indicated may result
in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference.
B-Tech International Limited, its distributors and dealers are not liable or responsible for
damage or injury caused by improper installation, improper use or failure to observe these
safety instructions. In such cases, all guarantees will expire.
General
B-Tech International Ltd recommends that a professional AV installer or other suitably qualified
person install this product. Great care must always be taken during installation as most AV
equipment is of a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during installation and at
any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are
installing. This weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pay careful attention to where this product is located. Some walls are not suitable for
installation.
If located in a public or frequently populated area ensure that the product is out of the
immediate reach of people. If any AV equipment is to be suspended over the likely path or
location of people then great care should be taken to secure all parts of the installation from
falling.
If you install this product on drywall it must be securely fixed to a wooden stud, concrete block
or other permanent structure behind the drywall board. Installing on drywall boards alone will
not support the weight of most AV equipment.
When drilling holes in walls it is essential to avoid contact with electrical cables and water or
gas pipes contained within. Use of a good quality live wire detector and hidden object locator is
therefore recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all wall fixing screws be used where supplied and that the
purpose of all other fixing hardware is fully understood. In some cases more AV equipment
fixing hardware will be supplied to accommodate different models of equipment and set up
configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the
product might provide and ensure that all cables are tidy and secure. Check to see that any
moving aspect of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Double-
check all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualified person.

3
CS
Spolenost B-Tech International Ltd. doporuuje provést instalaci tohoto produktu prostednictvím odborného
instalátora AV i jinak zpsobilé osoby. Spolenost B-Tech International Ltd, její distributoi a prodejci nenesou
odpovdnost za škody nebo zranní zpsobená nevhodnou instalací. Tento výrobek je nutno umístit do vhodné
konstrukce a používat jen po uvedenou maximální výšku.
DE
B-Tech International Ltd. empfiehlt, dass dieses Produkt durch einen qualifizierten AV-Techniker oder eine
andere Person mit geeigneter Qualifikation installiert wird. B-Tech International Ltd, ihre Distributoren und
Händler können nicht für durch fehlerhafte Montage verursachte Beschädigung oder Verletzung haftbar bzw.
verantwortlich gemacht werden. Dieses Produkt muss auf eine geeignetem Untergrund montiert werden und darf
nur bis zum angegebenen Höchstgewicht verwendet werden.
ES
B-Tech International Ltd. recomienda que un instalador de audio y video profesional u otra persona debidamente
cualificada instalen este producto. B-Tech International Ltd, sus distribuidores y concesionarios no se hacen
cargo ni se responsabilizan de ningún daño o lesión provocados por una instalación inapropiada. Este producto
se debe montar en una estructura adecuada y se debe utilizar soportando solamente hasta el peso máximo
indicado.
FR
B-Tech International Ltd. recommande de confier l’installation de ce produit à un installateur AV professionnel ou
à une autre personne dûment qualifiée. B-Tech International Ltd, ses distributeurs et ses revendeurs ne
sauraient être tenus responsables de tout dégât ou de toute blessure résultant d’une installation incorrecte. Ce
produit doit être monté sur un support approprié et utilisé dans la limite du poids maximum indiqué.
IT
B-Tech International Ltd. consiglia di affidare l’installazione di questo prodotto a un installatore specializzato o ad
altra persona adeguatamente qualificata. B-Tech International Ltd, i suoi distributori e rivenditori non accettano
alcuna responsabilità nei riguardi di eventuali danni o infortuni causati da un’errata installazione. Questo prodotto
deve essere fissato a una struttura idonea e utilizzato unicamente sino al peso massimo indicato.
NL
B-Tech International Ltd. adviseert om dit product te laten installeren door een professionele AV-installateur of
andere hiervoor gekwalificeerde persoon. B-Tech International Ltd, haar distributeurs en dealers zijn niet
aansprakelijk of verantwoordelijk voor schade of letsel die is veroorzaakt door onoordeelkundige installatie. Dit
product moet worden gemonteerd aan een geschikte constructie, waarbij het aangegeven maximum gewicht niet
mag worden overschreden.
PL
Firma B-Tech International Ltd. zaleca, aby ten produkt by instalowany przez profesjonalnych instalatorów AV
lub inny odpowiednio przeszkolony personel. Firma B-Tech International Ltd, jej dystrybutorzy i dealerzy nie
ponosz odpowiedzialnoci za uszkodzenia lub obraenia ciaa powstae w wyniku nieprawidowej instalacji.
Niniejszy produkt musi by zamontowany na odpowiedniej powierzchni, a podczas uytkowania nie wolno
przekracza podanego maksymalnego obcienia.
PT
A
B-Tech International Ltd. recomenda que a instalação deste produto seja efectuada por um instalador de AV
profissional ou outra pessoa devidamente habilitada. A B-Tech International Ltd. e os seus distribuidores e
concessionários não são responsáveis por danos ou lesões causados por uma instalação incorrecta. Este
produto tem de ser montado numa estrutura adequada e utilizado somente até ao peso máximo indicado.
RU
 B-Tech International Ltd. ,     
   -     
.  B-Tech International Ltd.,       
   ,     .   

BT8222
PARTS LIST
4
Suitable for loads
up to
60kg (132lbs)
1
2
3
4
5
6
6
7
7
8
9
10
10
11 12
13
14
15
INTERFACE ASSEMBLY
WALL PLATE &
ARM ASSEMBLY
16
17
17

5
PLEASE KEEP THIS FOR FUTURE REFERENCE
REF PART NAME QTY
1 WALL PLATE 1
2 FIXING PLATE 1
3 ARM 1
4 TILT PLATE 1
5 HOOK PLATE 1
6 CROSS RAIL 2
7 INTERFACE ARM 2
8 M10 METAL WASHER 4
9 M10 x 25mm HEX SCREW 4
10 M8 x 20mm HEX SCREW 4
11 TILT ADJUSTMENT HAND LEVER 1
12 M8 NUT 2
13 M8 METAL WASHER 2
14 M6 x 8mm HEX SCREW 6
15 PLASTIC CAP 4
16 ADJUSTMENT FIXING PLATE 2
17 M6 x 15mm SCREW 8
18 5mm HEX KEY (FOR PART 10) 1
19 6mm HEX KEY (FOR PART 9) 1
20 13mm/17mm SPANNER (FOR PARTS A1 & 12) 1
INTERFACE KIT
A M4 x 15mm SCREW 4
B M4 x 35mm SCREW 4
C M5 x 15mm SCREW 4
D M5 x 35mm SCREW 4
E M6 x 15mm SCREW 4
F M6 x 35mm SCREW 4
G M8 x 15mm SCREW 4
H M8 x 35mm SCREW 4
I MULTIWASHER 4
J M8 x 15mm SPACER 4
WALL FIXING KIT
A1 M10 x 90mm COACH SCREW 4
A2 M10 METAL WASHER (FOR PART A1) 4
A3 No. 12 WALL PLUG (FOR PART A1) 4
18 19
20
AB C D E F G HJ
I
FLAT SCREEN INTERFACE KIT
(FOR ATTACHING MOUNT TO BACK OF FLAT SCREEN)
WALL FIXING KIT
(FOR FIXING MOUNT TO WALL)
A2
A1 A3

1
INSTALLATION INSTRUCTIONS
6
OPTIONAL: To adjust position of the wall arm on the wall plate, remove
parts 8, 9 and 16. Then move fixing plate to desired position, then re-attach
parts 8, 9 and 16.
19
19
16
16 16 8
9
19
2
1
89
1
89

7
2Fix wall plate to the wall using one of the following methods.
i. Brick / concrete walls.
A1
A2
1
A3
12mm (15/32")
masonry bit

8
ii. Wood / wood stud walls.
A1
A2
1
8mm (5/16")
wood bit
MAX16"
STUD FINDER
(Optional)

9
3
OPTIONAL : For horizontal fixings between 380mm and 140mm, remove interface
arms and attach in the vacant position closer to the centre of the interface.
Attach interface to screen.
TOP
BOTTOM
FLAT
SCREEN
i. Adjust interface arms to suit the flat screen's fixing pattern.
6
7
7
6
7
7
77
6
6
17
17

10
ii. Attach the interface arms to the flat screen.
TOP
BOTTOM
FLAT
SCREEN
J
I
HGFE
DCBA A
FLAT
SCREEN
RECESS
SPACER
SCREW
INTERFACE
ARM WASHER
FOR SCREENS WITH RECESS FIXINGS

11
4Hook the screen onto the tilt plate.
WALL
FLAT
SCREEN
4
5
5
4

12
ii. Level screen then fix in place using parts 12 & 13.
FLAT
SCREEN
5
12
13
TOP
BOTTOM
20
SCREEN LEVELLING

13
5Attach plastic caps (parts 15) to the cross rails (parts 6).
FLAT
SCREEN
15
6
15
15
6

14
6Cable management.
CABLE
CABLE
FLAT
SCREEN
3
3
WARNING:
Ensure arm is fully
extended before
connecting cables.
CAUTION: Ensure there is adequate cable slack for movement of the
screen, and that cables will not be pinched when the mount is closed.

15
7Loosen the tilt adjustment hand lever to adjust tilt, then retighten to fix
position.
+15°
WALL
FLAT
SCREEN
11
11

16
8To fix the cantilever arm position, tighten parts 10.
120°
180°
FLAT
SCREEN
FLAT
SCREEN
WALL
WALL
18
18
10
10
10

17
8OPTIONAL: For minor lateral adjustment, loosen part 9, then slide fixing
plate to suitable position.
19
9
2
19
2
9
FLAT
SCREEN
WARNING
Only loosen screws.
Do not remove

18
BT8222
PRODUCT DIMENSIONS
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
410mm
16.1"MAX 115mm 4.5"MIN

19
BT8222
PRODUCT DIMENSIONS
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
INTERFACE
430mm
16.9"
380mm 15" 410mm 16.1"
550mm
21.7"
WALL PLATE
790mm
31.1"MAX
508mm 20"MAX
545mm 21.5"
820mm
32.3"
140mm
5.5"MIN
90mm 3.5"
90mm 3.5"
500mm
19.7"
230mm 9.1"

www.btechavmounts.com
B-TECH AUDIO VIDEO MOUNTS
HEAD OFFICE
Bennett House, Long March, Daventry, Northants NN11 4NR, UK
Email: [e-mail]
©2010 Bennett Technologies Limited. All rights reserved.
B-Tech Audio Video Mounts is a division of Bennett Technologies Limited.
B-Tech, Better By Design & Mountlogic are registered trademarks of Bennett Technologies Limited.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
EUROPE
Brixtonlaan 32, Zaventem 1930,
Brussels, Belgium
Email: inf[email protected]om
SINGAPORE
Ruby Industrial Complex,
Singapore 347740
Email: [e-mail]
NORTH AMERIC
A
203 Eggert Road,
Buffalo, NY 14215, USA
Email: [e-mail]
ASIA PACIFIC
1503 Prosperity Millennia Plaza,
Quarry Bay, Hong Kong
Email: [e-mail]
IP-BT8222-V1-OR2BX-170610-21 MADE IN CHINA