B-Tech System 2 BT7051 User manual

BT7051
50MM (2 INCH) LARGE ACCESSORY COLLAR
WITH COVERS
©Copyright 2009.
www.btechavmounts.com
v.0209 OR1BX
Asia Pacific
B-Tech International (Hong Kong) Ltd.
23rd Floor, Manulife Tower, North Point, HK
Tel: [phone] Fax: [phone]
Email: [email protected].hk
Europe
B-Tech PRO-AV bvba
Brixtonlaan 32, Zaventem 1930,Brussels, Belgium
Tel: [phone] Fax: [phone]
Email: [email protected]
North America
B-Tech Audio VideoMounts.
10 Greg Street, #108, Sparks, NV 89431, USA
Tel: [phone] Fax: [phone]
Email: [email protected]
Head Office
B-Tech International Ltd.
Bennett House, Long March, Daventry, Northants NN11 4NR, UK
Tel: [phone] Fax: [phone]
Email: [email protected]
PAGE 1 / 2
This pack contains:
1 heavy duty collar with covers Caution:Do not exceed the maximum weight limit indicated for this product.
Failure to comply may cause instability and possible serious injury.
Made in China
•Heavy duty accessory collar for use with 50mm (2”) poles
•Provides attachment for B-Tech modulus system mounts
•Double attachment
•Aesthetic cover plates included to hide fasteners
68
O52
24
24
84
51
Important Safety Instructions.
Read first
Do not attempt to install this product until all instructions and warnings have been read and
properly understood. Please keep these instructions for future reference.
B-Tech International Limited, its distributors and dealers are not liable or responsible for
damage or injury caused by improper installation, improper use or failure to observe these
safety instructions. In such cases, all guarantees will expire.
General
B-Tech International Ltd recommends that a professional AV installer or other suitably qualified
person install this product. Great care must always be taken during installation as most AV
equipment is of a fragile nature, possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely,
then please consult a professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during installation and at
any time thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are
installing. This weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Product location
Please pay careful attention to where this product is located.
If located in a public or frequently populated area ensure that the product is out of the
immediate reach of people. If any AV equipment is to be suspended over the likely path or
location of people then great care should be taken to secure all parts of the installation from
falling.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and that the purpose of
all other fixing hardware is fully understood.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
Some products have moving parts and the potential to cause injury through the crushing or
trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Double-
check all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV
installer or other suitably qualified person.
This collar is intended for use only with the maximum
weights indicated. Use with heavier than the maximum
indicated may result in instability causing possible injury.

PLEASE KEEP THIS PARTS LIST FOR FUTURE REFERENCE
PARTS LIST
No
PART NAME DESCRIPTION QTY
1 BT7051 COLLAR TO FIT 50mm POLES
1
2 M8 X 15mm GRUB SCREWS TO CLAMP COLLAR TO POLE
4
3 M8 SPRING WASHER SITS UNDER SCREW HEADS 9
4 M8 X 12mm FLAT CROSS HEAD
SCREW
TO ATTACH ACCESSORIES
8
5 M8 X 65mm SAFETY BOLT PASSES THROUGH POLE
1
6 BT7051 COLLAR COVER HALF PUSH FIT AROUND COLLAR 2
7 4mm ALLEN KEY TO TIGHTEN (PART 2)
1
8 5mm ALLEN KEY TO TIGHTEN (PART 5)
1
Attention!
Ensure safety bolt (Part 5)
is in place before any AV
equipment is fitted.
1
2
3
4
5
6
78
BT7051
PARTS LIST
Spare screws and
washers are provided
for use on the other
side of the collar if two
accessories need to
be attached.
Covers cannot be
used in this situation.
3
4
v.0209 OR1BX
PAGE 2 / 2