B2 Mono Quattro User manual

HIGH PERFORMANCE AMPLIFIERS
OWNER'S MANUAL

FEATURES
Circuit Configuration
Frequency Response
Signal to Noise Ratio
Input Sensitivity
Input Level Selector
Crossover
High Pass Filter
Low Pass Crossover Range
Subsonic Crossover Range
Bass Boost
Phase
Output Master / Input Slave
Remote Control
Damping Factor
Power Terminal gauge
B2 series output power
POWER @ 4OHM POWER @ 2 OHM POWER @ 1OHM
Mono 570W x 1 1000W x 1 1800W x 1
POWER @ 4OHM POWER @ 2 OHM POWER @ 4 OHM MONO
Quattro 100W x 4 160W x 4 320W x 2
Mono
Ultra Class D Mono
: 20Hz ~ 250Hz
: 100dB
: 6V ~ 0.2V
: No
: 24dB / Oct
: no
: 20Hz ~ 200Hz
: 10Hz ~ 50Hz
: 0 ~ 9dB
: 0 ~ 180 Degree
: YES
: YES
: 250<
: 0 ga x 1
( Linked : 360A )
All features are subject to change in the continuing effort to improve the products without notice
1. FEATURES
2. DESIGN FEATURES
1) Mono will allow stable operation as a single unit @ 4/2/1 ohms impedance.
Mono will allow daisy chain connections @ impedances down to 2 ohms.
2) Quattro 4 ch class AB amplifier will allow stable operation @ 4/2 ohms stereo and 4 ohms mono.
3) B2 amplifiers offer an advanced protection circuit for the benefit of the user.
Speaker short circuitry, DC offset, Voltage sensor & thermal protection.
4) The B2 pcb has been designed using a double sided board and features high current mosfet
switching devices.
Mono has a 24 dB slope/Oct low pass & subsonic filter.
Quattro has a 12 dB slope/Oct high pass and low pass filter
5) Mono & Quattro offer wired remote level control which allows easy gain adjustment from
the drivers seat.
6) Mono can be used in a daisy chain connection. This will allow bridging of 2 mono amplifiers
@ 2 ohms to produce twice the power of one unit @ 1 ohm
Quattro
4ch Class AB
: 20Hz ~ 30KHz
: 105dB
: 6V ~ 0.2V
: LOW/HIGH
: 12dB / Oct
: 50Hz ~ 1KHz
: 30Hz ~ 500Hz
: 10Hz ~ 100Hz
: 0 ~ 18dB
: No
: No
: YES
: 250<
: 0 ga x 1
B2 has through years of dedication introduced our line of Mono & Quattro amplifiers.
The B2 line up are made to fullfil our philosophy for amplifiers; A variety of applications, highest
possible efficiency and great appearance.
The B2 amplifiers are designed to produce high power levels even from stock electrical systems.
High efficiency is created from updating every stage through the amplifiers' circuit. High speed
controller chipsets, efficient power devices, precise thermal management and the best engineering
are the cornerstones of the B2 amplifier series.
1
Fuse Rating : 180A : 3 x 30A
(13,8V, 0,02% THD)

INPUT
Connect preamp signal cables from
the headunit to RCA Input of Mono.
OUTPUT
Output RCA for signal routing to another amplifier.
POWER & PROTECTION INDICATOR
Power BLUE, Green-lit shows correct operation
Protect LED, RED-lit shows general malfunction,
faulty connection or thermal protection
GAIN ( 6V ~ 0.2V )
Matching the output voltage of the headunit's
RCA line-outs to Mono input section.
SUBSONIC FILTER ( 10Hz ~ 50Hz @ 24dB/Oct )
Adjusts the subsonic cut off point to eliminate low
frequencies.
BASS BOOST
Variable bass boost from 0-9 dB @ 45 Hz
REMOTE LEVEL CONTROL PORT
Connection of external level control.
LOW PASS FILTER ( 35Hz ~ 250Hz @ 24dB/Oct )
Adjusts the cut off point for the low pass filter.
PHASE CONTROL
Variable phase adjustment from 0-180 degrees.
OUTPUT MASTER / INPUT SLAVE
For daisy chain connection of 2 Mono amplifiers
down to 2 ohms.
3. CONTROL & CONNECTION
3-1. Mono CONTROL & CONNECTION
3-2. Quattro CONTROL & CONNECTION
INPUT
Connect preamp signal cables from
the headunit to RCA Input of Quattro.
OUTPUT
Output RCA for signal routing to another amplifier.
POWER & PROTECTION INDICATOR
Power BLUE, Green-lit shows correct operation
Protect LED, RED-lit shows general malfunction,
faulty connection or thermal protection
INPUT LEVEL
INPUT LEVEL selects Low/High level input from headunit
if you set it to Low, then Rca Jack receives Low input
If you set it to high, then Rca jack receives High input.
GAIN ( 6V ~ 0.2V )
Matching the output voltage of the headunit's
RCA line-outs to Quattro input section.
SUBSONIC FILTER ( 10Hz ~ 100Hz @ 12dB/Oct )
Adjusts the subsonic cut off point to eliminate low
frequencies.
BASS BOOST
Variable bass boost from 0-18 dB @ 45 Hz
2

REM ( REMOTE )
Connect to switched +12V with trigger from head unit.
SPEAKER OUTPUTS
Amplifier connection to loudspeakers.
Minimum speaker cable is 12 gauge.
Mono minimum impedance is 1 ohm if used as
a single unit.
Mono in linked mode offers stable opearation to
a minimum of 2 ohms.
Quattro minimum impedance is 2ohms stereo or
4 ohms mono
GND ( GROUND CONNECTION )
For connection to the chassis' ground.
For optimum performance 0 gauge cable is
recommended.
+12V ( POWER CONNECTION )
For connection to the positive terminal of the
battery (+12). For optimum performance
0 gauge cable is recommended.
3-3. Mono & Quattro CONTROL & CONNECTION
4. INSTALLATION
If you chose to install the B2 series by yourself, please read the owners' manual carefully.
Before you start your installation, please take all steps into consideration. Otherwise, please go to
www.b2-audio.com for authorized distributors or contact us directly for support.
4-1. MOUNTING PREPARATION
Disconnect the negative ( ) battery cable before mounting B2 series or making any connections.
Check the battery and alternator ground ( ) connections.
Make sure they are properly connected and free of corrosion. Before selecting a mounting location
for the amplifier, please take cooling and safety into consideration.
4-2. MOUNTING PREPARATION
B2 amplifiers have been designed with a good heat radiation heatsink to avoid excessive heat
from the amplifier circuitry. For optimum heat radiation performance, it is recommended to
find a mounting location that allows for vertical installation of the heat sink fins.
HIGH PASS FILTER ( 50Hz ~ 1KHz @ 12dB/Oct )
Adjusts the cut off point for the high pass filter.
The wide frequency range allows for "Active" speaker
operation.
CROSSOVER SELECTOR
Configuration of the filter mode. HPF/FULL/LPF.
LOW PASS FILTER ( 30Hz ~ 300Hz @ 12dB/Oct )
Adjusts the cut off point for the low pass filter.
REMOTE LEVEL CONTROL PORT
Connection of external level control.
3

FUSE
180A
Ground
Remote turn on
Main Battery
12V
Headunit
+12V, GND, REM CONNECTION DIAGRAM
For safety purposes, install the amplifier in a dry and well ventilated location and
make sure no cables or other harness of the car is interfaced with the mounting location or
will present a hazard to the cars' cable, control cables, fuel lines/tanks, hydraulic lines or other
components of the vechicle.
4-3. +12V, GND, REM CONNECTION
12V ( POWER CONNECTION )
Before mounting B2 amplifiers, disconnect the negative ( ) wire from the battery to protect
any accidentIal damage to the amplifier or the audio system.
B2 series are designed to use 0 AWG power and Ground connection.
Connect the power cables to power terminal labeled as + 12V
Quattro is equipped with Fuses. But if you want to use external fuses, then connect one end of
the fuse holder to the power cable and the other end of the fuse holder to positive battery
within 20 cm of the same cable.
This fuse location will protect the system and the vehicle against the possibility of a short circuit
in the power cable. Be sure to use fuses and a fuse holder adequate for the application
GND ( GROUND CONNECTION )
Locate a secure grounding connection as close to the amplifier as possible.
Make sure the location is clean and provides a direct electrical connection to the frame
of the vehicle. Connect one end of a short piece of the same size cable as the power cable
to the grounding point. Run one end of the cable to the grounding point.
Run the other end of the cable to the mounting location.
Connect the ground cable to the screw terminal labeled as GND.
REM ( REMOTE CONNECTION )
Run a remote turn on cable from the switched + 12V source.
This may be a toggle switch, a relay, or your source unit's remote trigger cables, or power antenna
trigger cable.
Connect the remote turn on cable to the power terminal labeled as REM.
4

CAUTION
Mono minimum impedance is 1 ohm.
or
Mono Linked minimum impedance is 2 ohm
Mono SPEAKER CONNECTION DIAGRAM i
4-4. SPEAKER CONNECTION
B2 amplifier series recommends 12 AWG speaker connecting cables.
Run 12 AWG speaker connecting cables from your speakers to amplifiers' mounting location
Keep speaker cables away from power cables and B2 series amplifier's input cables.
Use grommets anywhere the cables have to pass through the holes in the metal frame or sheet
metal. Connect to the speakers according to terminals on each speaker.
Strip 3/8" of insulation from the end of each cable and twist the cables strands together tightly.
Make sure there are no stray strands that might touch other cables or terminals and cause a short circuit.
Crimp spade lugs over the cable ends or tin the ends with solder to provide a secure termination.
Mono SPEAKER CONNECTION DIAGRAM ii
8 ohm ~
2ohms
8 ohm
~ 2ohms
8 ohm
~ 1ohms
5
Connect the cable ends to B2 series amplifiers as shown on the speaker system diagram.

Tweeter
Passive
MidRange
/Bass
Passive
MidRange
/Bass
Tweeter
Tweeter
8 ohm
~ 4ohms
Passive
MidRange
/Bass
8 ohm
~ 4ohms
Passive
Tweeter
MidRange
/Bass
Passive
MidRange
/Bass
Tweeter
Quattro SPEAKER CONNECTION DIAGRAM i
Quattro SPEAKER CONNECTION DIAGRAM ii
Quattro SPEAKER CONNECTION DIAGRAM iii
6

HeadUnit
Mono MASTER AMPLIFIER
4-5. Mono DAISY CHAIN CONNECTION
Daisy chain connection allows linking of 2 mono amplifiers to work as 1.
Step 1. Connect the master Mono amplifier to the head-unit and set its output master
Step 2. Connect the master and slave Mono amplifier in daisy chain Rca jack as shown
in the diagram.
Step 4. Connect speaker cable ( + ) on master Mono amplifier to subwoofer ( + )
Step 5. Connect speaker cable ( + ) on slave Mono amplifier to subwoofer ( )
Step 6. Connect speaker cable ( ) on master Mono amplifier to speaker cable ( ) on slave amplifier
Mono Minimum daisy chain connection impedance is 2 ohm
Do not use daisy chain connection in 1 ohm
Mono SLAVE AMPLIFIER
7
Please read the following connection diagram cautiously to ensure the correct connection.
and input slave switch to the output master position.
Step 3. Set the slave Mono amplifier output master & input slave switch to the slave input position.

Mono Minimum daisy chain connection impedance is 2 ohm
Do not use daisy chain connection in 1 ohm
Mono working Voltage is 9V ~ 16V.
CAUTION
FUSE
360A
Main Battery
12V
Headunit
GROUND
8
8 ohm
~ 2ohms

5. TROUBLE SHOOTING TIPS
NO SOUND ( NO OUTPUT )
terminals to see if there is any movement of the speaker cone.
PROTECTION
Quattro minimum working impedance is 2 ohm stereo or 4 ohm mono
Voltage lower than 8.5V or higher than 16V will cause the amplifier to go into protect.
Check whether B2 series amplifiers work after removing RCA-Input
If B2 series amplifiers are functional, then check DC by checking RCA-input L and R
When DC is over 4V at input, try by replacing headunit or source unit
DISTORTION
with upgraded ones.
POOR BASS RESPONSE
BUZZING SOUND
WHINING NOISE
components, battery or alternator, so pls check all grounding connection.
9
2) Pls check fuses ,If they are blown, pls replace with new ones.
1) Pls check all connections, cables' rounting, short, voltage at Mono & Quattro amplifiers
and headunit
3) Pls check whether speakers are functional. You can connect a AA battery to the speaker
1) Pls check overload, overheat ( thermal ), short and voltage. DC offset
2) Minimum working impedance is 1 ohm for single Mono amplifiers or 2 ohm for linked operation.
3) If Mono & Quattro amplifiers are shut down due to overheat, they will start up again after
a short cooling period.
Please allow for better airflow and ensure there's no obstruction around the Mono & Quattro for
thermal protection
4) Mono has low and high voltage protection. Working voltage is 9V~16V.
5) When over 4V DC comes into B2 series amplifiers, then, they will be DC protected.
1) Adjust the input level and check the quality of the speakers. Replace low quality speakers
1) Pls check speaker cables and reverse the polarity of one channel
1) Check the amplifier and the head unit ground and ensure it has a good clean connection
2) Check the Rca jack and replace it if faulty or try rerouting it.
1) Engine noise is caused by poor grounding of B2 series amplifiers, headunit, other