Baby's Dream Cirque Crib User manual

Cirque Crib
Instruction Sheet
Read All Instructions Before Assembling Crib. Keep Instructions For Future Use.
Allen
Wrench
Front Frame
Adult
Rail
DO NOT substitute parts. Contact 1-800-TEL-CRIB for replacement parts and instructional literature if needed.
(Spring) Mattress Support
PARTS LIST
(1) Front Frame Assembly
(1) Back Frame Assembly
(2) Right Side Assembly
(2) Left Side Assembly
HARDWARE LIST
(2) Caps
(2) M8*100mm Flat Head Bolts
(2) M8*80mm Flat Head Bolts
(8) M8*25mm Round Head Bolts
(4) M6*15mm Round Head Bolts
(8) M8 Metal Washers
(4) M6 Metal Washers
(1) Allen Wrench
(1) Mattress Support (Spring)
ITEMS INCLUDED WITH ADULT BED CONVERSION
(sold separately)
(2) Set of Metal Adult Rails (5) Cross Slats
(4) Bolt Caps
(2) M8*25mm Flat Head Bolts
(2) M8*60 mm Flat Head Bolts
(18) M8*25mm Round Head Bolts (10 for cross slats)
(18) M8 Metal Washers (8 pcs for cross slats)
(8) Plastic Washers
(1) Allen Wrench
Side Frames (2)
Model___________________________ MFG. Date______________________ P.O. #______________________
M8 Metal
Washer
M8 Plastic
Washer
Bolt Cap
Cap
M6 Metal
Washer
Cross Slat
M6* 15mm
Round Head Bolt
Back Frame
M8* 25mm
Flat Head Bolt
M8* 25mm
Round Head Bolt
M8* 60mm
Flat Head Bolt
M8* 80mm Flat Head Bolt
M8* 100mm Flat Head Bolt

CRIB ASSEMBLY INSTRUCTIONS
Step 1: To begin, you will need the Right and Left Side
Frames, two caps, two M8*80mm Flat Head
Bolts, four M8*25mm Round Head Bolts,
four M8 Metal Washers and the Back
Frame Assembly. Attach one
cap to the highest part of
the top rail of the Right
Side Frame and align the
frame to the Back Frame
Assembly making sure the
top rail is aligned with the top
hole of the Back Frame. You
will attach the Right Side
Frame with the cap to the Back
Frame Assembly using a
M8*80 mm Flat Head Bolts by
sliding the bolt thru the top
pre-dilled
hole of the
Back Frame. Then,
you will slide two M8*25mm
Round Head Bolts and two
washers thru the bottom hole. Now,
using your Allen Wrench tighten all the
bolts at this time. ***Repeat the steps for the
Left Side Frame.
Next, you will need to attach the Front Frame. For this step,
you will need the Front Frame Assembly, four M8*25mm
Round Head Bolts, and four M8 Metal Washers. First, remove
the protection caps at the end of the Right Side Frame using
the Allen Wrench. Then, attach the Front Frame to the Right
Side Frame using two M8*25mm bolts and two M8 Metal
Washers. Slide the bolts thru the two bottom pre-drilled holes
on the Right Side Frame post into the inserts of the bottom
post of the Front Frame Assembly. Next, slide an M8*100mm
Flat Head Bolt into the hole in the ball on the top of the Front
Frame Assembly into the nut of the Right Frame top rail end.
Now using your Allen Wrench tighten all the bolts at this time.
***Repeat the steps for the Left Side Frame.
In this step, you will attach the Mattress Support by using four
M6*15mm Round Head Bolts and four M6 metal washers,
and the Allen Wrench. Swing the support arms out on the
Mattress Support and place them in the against the desired
Mattress Support holes level. Slide the bolts with the washers
thru the Mattress Support arm into the Back Frame and Front
Frame post holes. Tighten all the bolts at this time using the
Allen Wrench.
Step 2:
Step 3:

ADULT BED CONVERSION
Conversion from crib using Adult Conversion Kit by Baby’s Dream (sold separately).
Step 1:
***If you are converting from crib to adult bed, follow these
steps. If not, please move on to step 2.
Remove the Mattress Support by removing the four M6*15mm
bolts with the
Allen Wrench.
Using the same
wrench, you are
then going to
remove the Front
Frame Assembly
connected with
the two M8*25mm
bolts and two
M8*80mm bolts.
Finish by
removing the Side
Frame Assemblies
by removing the rest of
the M8*25mm bolts and
M8*80mm bolts that attach the
sides to the Back Frame Assembly
with the Allen Wrench.
To attach the metal side rails (packaged in
the Adult Conversion Kit) to the
Headboard and the Footboard, you will
need eight M8*25mm Round Head Bolts, eight M8 Metal Washers, eight Plastic Washers, and
your Allen Wrench. You’re going to align a Plastic Washer followed by the adult rail then the
M8 Metal Washer and the M8*25mm bolt in the second-to-bottom and third-to-bottom holes.
The Plastic Washer should be between the back or front frame and adult rail. Tighten the bolts
at this time. ***Repeat the steps for the Front Frame Assembly and the opposite side adult rail.
To attach the five metal cross slats to the metal side rails, you will need ten M8*25mm Round
Head Bolts, ten M8 Metal Washers, and the Allen Wrench. You will align the M8*25mm Round
Head Bolts with the M8 Metal Washers then pass them through the pre-drilled holes under
the metal adult rails. Slide the bolt into the nut in the metal cross slats and tighten the bolts at
this time using the Allen Wrench. ***Repeat the steps for each metal cross slat on both sides
of the metal rails.
In the Front Frame Assembly, you will need to cover the holes on the balls in the top rail
corners and on the post of the Back Frame Assembly. For this, you need two bolt caps, two
M8*60mm Flat Head Bolts, two M8*25mm Flat Head Bolts and the Allen Wrench. Insert the
caps on any of the balls through the upper hole and attach the M8*60mm Flat head Bolt
through the bottom. Then, insert the cap on any of the upper holes on the Back Frame post
through the front of the post and attach the M8*25mm Flat Head Bolt through the back.
Tighten the bolts with the Allen Wrench at this time. ***Repeat the steps for the opposite ball
and opposite post. Now your adult bed assembly is complete.
The adult bed is not intended to be used by children under 6 years of age without proper adult
supervision. This adult bed is NOT a toy. DO NOT allow children to play or climb on adult bed.
Step 2:
Step 3:
Step 4:

REV 12/14