Babyletto Gelato 12901 User manual

Gelato 4-in-1 Cot Assembly Instructions
Item# 12901
1
revised 10DEC2019

* Tools Needed (not included)
Phillips screwdriver
2
Thank you for purchasing this nursery product! To ensure safe use of your product, please follow
these assembly instructions closely. If you are missing parts or have any questions, please visit our
website at www.designkids.com.au.
For assembly, use the Allen wrench if it is included in the hardware box. We also recommend using
a Phillips head screwdriver (not included) to complete assembly. Please do not substitute parts or
use power screwdrivers. Our pieces are made from natural woods. Due to the nature of wood, some
variation in color, grain, or texture is to be expected.
We hope you and your growing family enjoy our product.
With thanks,
Ubabub International Pty Ltd
* You will need two people to
assemble this cot.
Thank you for purchasing this nursery product! To ensure safe use of your product, please follow
these assembly instructions closely. If you are missing parts or have any questions, please visit our
website at www.designerbabybrands.co.nz
For assembly, use the Allen wrench if it is included in the hardware box. We also recommend using
a Phillips head screwdriver (not included) to complete assembly. Please do not substitute parts or
use power screwdrivers. Our pieces are made from natural woods. Due to the nature of wood, some
variation in color, grain, or texture is to be expected.
We hope you and your growing family enjoy our product.
With thanks,
Designer Baby Brands Limited
For New Zealand :
For Australia :

H5. Lock Washer (24)H2. 4.4 cm Allen Head Bolt (4)
H1. 5.08 cm Allen Head Bolt (16)
B. Side Panel (2)A-1. End Panel (2)
E. Foot (4)
G. Toddler Bed Conversion Kit
C-1. Front Left Leg
C-2. Front Right Leg
D-1. Rear Left Leg
D-2. Rear Right Leg
F-1. Mattress Support U12901
H7. 3.8 cm Allen Head Bolt (4) H8. Nut (4)
H6. Allen Wrench
PARTS
Not to Scale
HARDWARE
Bolts in Actual Size
H9. 2.0 cm Allen Head
Bolt with cap (4)
3

ASSEMBLY INSTRUCTIONS
X4
E
H5
H1
H5
H1
H5
H1
H5
H1
A-1
C-1 D-1
H1
H5 X8
H5
H1
H5
H1
H5
H1
H5
H1
A-1
D-2 C-2
1
2
C / D
E
C / D
DO NOT OVERTIGHTEN.
4

H1
H5
B
A-1
A-1
C-1
C-2
D-1
D-2
H1
H5
H1 H5
H1 H5
B
X4
H5 H1
DO NOT OVERTIGHTEN.
3
5

H9
X4
CARE AND SAFETY:
THIS UNIT IS SUPPLIED WITH EXTRA BOLTS THAT SECURES THE HOLES ACCESSIBLE TO
THE CHILD. FAILURE TO USE THIS COULD RESULT DANGER. WE RECOMMEND THAT YOU
USE THIS SAFETY DEVICE.
When putting the mattress support (F-1) at the higher position, use the provided bolts and caps (H9)
and plug the corresponding holes at the lower position as illustrated. Tighten each bolt with the Allen
wrench (H6). You will install totally 4 sets of bolt and cap.
If putting the mattress support (F-1) at the lower position, use the provided bolts and caps (H9) and
plug the corresponding holes at the higher position. Tighten each bolt with the Allen wrench (H6). You
will install totally 4 sets of bolt and cap.
DO NOT OVERTIGHTEN.
H9
H9
H9
H9
A-1 B
A-1
4
6

!
* Make sure the mattress support U12901 (F-1) is level.
H1
H5
H8
H7
H5
DO NOT OVERTIGHTEN.
X4
X4
H8
H7
H5
H8
H7
H5
H8 H7
H5
H8
H7 H5
A-1
A-1 A-1
B
B
B
A-1
H1
H5
H1
H5
H1
H5
H1
H5
F-1
5
6
7

CAUTION: ANY MATTRESS USED IN THIS COT MUST BE AT LEAST 27 1/4 INCHES (69CM)
BY 51 5/8 INCHES (131CM) WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).
Please refer to the label (sample below) on the inside face
of the headboard. Record the model/ item number and serial
number of your cot, the name of the store where you made
the purchase, the date of purchase and the wood finish in
the box to the lower right.
WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL
WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE
REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR
WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE
REFERENCE.
Please read the Caution and Warning
Statements insert before using your cot.
SAMPLE LABEL
THIS PRODUCT CONFORMS TO THE
APPLICABLE REGULATIONS OF THE
CONSUMER PRODUCTS SAFETY COMMISSION.
CAUTION: ANY MATTRESS USED IN THIS COT
MUST BE AT LEAST 27 1/4 INCHES (69CM) BY
51 5/8 INCHES (131CM) WITH A THICKNESS
NOT EXCEEDING 6 INCHES (15CM).
KEEP THIS MANUAL IN A
SAFE PLACE FOR FUTURE
REFERENCE.
Recheck all screws and bolts to
be sure they are fastened
securely. Do not overtighten.
Before using your cot, please
read all cautionary statements
on the insert sheet.
Finish
7
8

WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING
COT. KEEP THE MANUAL FOR FUTURE USE.
WARNING:
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
•
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed•
on their backs to sleep, unless otherwise advised by your physician.
Strangulation Hazard: Strings can cause strangulation! Do not place items with•
a string around a child’s neck, such as hood strings or pacifier cords. Do not
place cords, straps,or similar items that could become wound around the child’s
neck in or near this cot. Do not suspend strings over a cot or attach strings to
toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the•
body or clothing on loose fasteners.
DO NOT place a cot near a window where cords from blinds or drapes may•
strangle a child. Do not place this cot near a window or a patio door where a
child could reach the cord of a blind or curtain and be strangled.
Fall Hazard: When a child is able to pull to a standing position, set the mattress•
to the lowest position and remove bumper pads, large toys and other objects
that could serve as steps for climbing out.
•
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use cot if
any parts are missing, damaged or broken. DO NOT substitute parts. Contact
Ubabub International Pty Ltd (for Australia) /
Designer Baby Brands Limited (for New Zealand)
for replacement parts and instructional literature if needed.
• DO NOT use a water mattress with this cot.
• For cots equipped with teething rails, replace teething rail if damaged, cracked
or loose.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic films as mattress covers
because they can cause suffocation.
Parents should ensure a safe environment for the
child by checking regularly, before placing the
child in the product, that every component is
properly and securely in place.
Please do NOT remove any wood screws
in the normal disassembly of the cot.
WARNING:
Do not use this cot if the child is able to climb out unaided or is taller than
35 in. (89cm).
• Do not use this cot if you cannot exactly follow the accompanying instructions. • Infants can suffocate in gaps between cot sides when
used with a mattress that is too small.
• Follow warnings on all products in a cot.
• Ensure that the sides are properly latched or locked
in place when the cot is occupied.
• The mattress used with this cot should not be more
than 15cm thick and should be of such length with
width that the gap between the mattress and the sides
of the cot is no more than 3cm when the mattress is
pushed into the corner of the cot.
• Place cot at a reasonable distance from curtains,
blinds, heater and power points.
• Keep medication, string, elastic, small toys or small
items, such as money, out of reach from any position in
the cot.
9

RECOMMENDED MATTRESS SIZE:
This cot has been manufactured for use with a mattress which
measures 690 mm wide by 1310 mm long and 150 mm (or
less) in thickness. The width and length are specified because
it is important that the gaps between the mattress and the
sides and ends of the cot will not exceed 40 mm when the
mattress is pushed to one side or end, and 20mm when the
mattress is centred in the cot. The thickness of the mattress
has been specified to ensure that the depth of the cot is greater
than 500 mm with the mattress base in the lower position to
minimize the risk of a child climbing or falling out of the cot.
WARNING:
TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED
TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.
Storage:
• Pine woods exchange moisture with the air adjusting to major changes in room temperature and humidity. There-
fore, it is best to place your furniture away from heating or air-conditioning vents.
• Sunlight is not friendly to solid wood furniture and prolonged direct exposure to harsh sunlight can discolor the
finish. Be careful not to place your furniture in direct sunlight for extended periods of time. As with all your fine furni-
ture, blot up spills immediately.
Care and Cleaning:
• Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on a soft rag.
Rinse and dry thoroughly. If you ever refinish this furniture, be sure to use only a non-toxic finish specified for
children’s products. If you choose to refinish this furniture, the warranty will be voided.
10

AUSTRALIA - WARRANTY
Ubabub International Pty Ltd warrants that your Gelato 4-in-1 Cot will be free from defects the
whole product for a period of one year, from the date of purchase. This warranty only applies
where the product is completely and correctly assembled and used in accordance with all
accompanying recommendations and users instructions. This warranty is in addition to your
rights under the Australia Consumer Law.
Ubabub International Pty Ltd will provide you with a replacement for this product if the Gelato
4-in-1 Cot becomes defective within the warranty period. Ubabub International Pty Ltd will bear
the reasonable expense of claiming the warranty. This warranty will no longer apply where the
defect is a result from installation and assembly, normal wear and tear, abuse, negligence,
improper use or alteration to the finish, design, and hardware of the cot.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Please retain your receipt as proof of purchase and contact Ubabub International Pty Ltd for
further assistance on how to process any warranty claims.
Business name: Ubabub International Pty Ltd
Business address: PO Box 4129, Ringwood VIC 3134
Phone number: [phone]
Email address: [email protected]
Manufacturer name: Hsing’s Industrial Corp
Manufacturer address: No.186, Chih Kan N.Rd. Tzu Kuan Hsiang, Kaohsiung Hsien,
Taiwan 826, ROC.
Contact us:
Ubabub International Pty Ltd
PO Box 4129, Ringwood VIC 3134
[phone]
[email protected]
www.designkids.com.au
revised17APR2019
11

NEW ZEALAND - WARRANTY
Designer Baby Brands warrants that your Gelato 4-in-1 Cot will be free from defects for a period
of one year from the date of purchase, in accordance with the New Zealand consumer
guarantees act. This warranty only applies where the product is completely and correctly
assembled and used in accordance with all accompanying recommendations and users
instructions..
The warranty will not cover or apply where the defect is a result from improper installation and
assembly, normal wear and tear, abuse, negligence, improper use or alteration to the finish,
design, and hardware of the cot.
Should an item be deemed defective due to faulty materials or workmanship during the warranty
period, it will be repaired or replaced at Designer Baby Brands discretion.
Please retain your receipt as proof of purchase and contact Designer Baby Brands for further
assistance on how to process any warranty claims.
Business name: Designer Baby Brands Limited
Business address: 22B Saunders Place, Avondale 1026, Auckland
Phone number: ([phone]
Website: www.designerbabybrands.co.nz
Manufacturer name: Hsing’s Industrial Corp
Manufacturer address: No.186, Chih Kan N.Rd. Tzu Kuan Hsiang, Kaohsiung Hsien,
Taiwan 826, ROC.
Contact us:
Designer Baby Brands Limited
22B Saunders Place, Avondale 1026,
Auckland
([phone]
www.designerbabybrands.co.nz
revised06DEC2019
12

* All of the parts and hardware you will need are supplied with the crib at the time of purchase.
Gelato 4-in-1 Cot Toddler bed conversion assembly
Item# 12901
13

H9
CARE AND SAFETY:
THIS UNIT IS SUPPLIED WITH EXTRA BOLTS THAT SECURES THE HOLES ACCESSIBLE TO
THE CHILD. FAILURE TO USE THIS COULD RESULT DANGER. WE RECOMMEND THAT YOU
USE THIS SAFETY DEVICE.
When putting the mattress support (F-1) at the lower position, use the provided bolts and caps (H9)
and plug the corresponding holes at the higher position as illustrated. Tighten each bolt with the Allen
wrench (H6). You will install totally 4 sets of bolt and cap.
X4
DO NOT OVERTIGHTEN.
H9
A-1
H9
A-1
H9
H9
X4
H1 H5
B
H1
H5
H1
H5
H1
H5
H1
H5
F-1
ASSEMBLY INSTRUCTIONS
1
2
14

WARNING : STRANGULATION HAZARD
Failure to follow these warnings and the assembly instructions could result in
serious injury or death from entrapment or strangulation.
Openings in and between bed parts can entrap head and neck of a small child. NEVER use bed with children
younger than 15 months. ALWAYS follow assembly instructions. NEVER place bed near windows where cords
from blinds or drapes may strangle a child. NEVER suspend strings over bed. NEVER place items with a
string, cord, or ribbon, such as hood strings or pacifier cords, around a child’s neck. These items may catch
on bed parts.
TO AVOID DANGEROUS GAPS, ANY MATTRESS USED IN THIS BED SHALL BE
A FULL-SIZE COT MATTRESS AT LEAST 51 5⁄8 IN. (131 CM) IN LENGTH, 27 1⁄4
IN. (69 CM) IN WIDTH, AND A MAX THICKNESS OF 6 IN. (15 CM).
THE INTENDED USER'S MINIMUM AGE MUST BE AT LEAST 15 MONTHS OLD
AND MAXIMUM WEIGHT MUST NOT EXCEED 50 LBS (22.7 KG).
3
DO NOT OVERTIGHTEN.
H2
H5 H2
H5
H2
H5
H5
H2
X4
G
H2
H2
H5
G
H2
H5
!
A-1 B
A-1
G
H2
H5
Finish
15

This cot is convertible to a full size bed. M5789 Full Size Conversion Rail is recommended,
please contact your retailer.
Item# 5789
Full Size Conversion Kit (5789 - Sold Separately)
16