Baileigh Industrial PT-44AH-W User manual

OPERATOR’S MANUAL
CONTROLLER OPERATION
MODEL: PT-44AH-W
© 2019 Baileigh Industrial Holdings LLC
REPRODUCTION OF THIS MANUAL IN ANY FORM WITHOUT WRITTEN APPROVAL OF BAILEIGH INDUSTRIAL
HOLDINGS LLC IS PROHIBITED. Baileigh Industrial Holdings LLC, Inc. does not assume and hereby disclaims any
liability for any damage or loss caused by an omission or error in this Operator’s Manual, resulting from accident,
negligence, or other occurrence.
Rev. 07/2019
Baileigh Industrial Holdings LLC
P.O. Box 531
Manitowoc, WI 54221-0531
Phone: [phone]
Fax: [phone]
[email protected]

Table of Contents
INTRODUCTION.............................................................................................................1
GENERAL NOTES..........................................................................................................1
SAFETY INSTRUCTIONS ..............................................................................................2
SAFETY PRECAUTIONS ...............................................................................................5
Dear Valued Customer:................................................................................................... 5
TECHNICAL INFORMATION AND SUPPORT...............................................................7
Read This Manual .......................................................................................................7
Work Condition............................................................................................................7
Maintenance................................................................................................................7
High Voltages..............................................................................................................7
TECHNICAL SUPPORT ................................................................................................. 8
Cleaning ...................................................................................................................... 8
INTRODUCTION.............................................................................................................9
System Characteristics................................................................................................9
Technical Standard.................................................................................................... 10
System Interface........................................................................................................ 10
SYSTEM BOARD AND MAIN INTERFACE.................................................................. 11
Operating Board Introduction..................................................................................... 11
Power On Process And Main Interface......................................................................12
CUTTING FUNCTION................................................................................................... 14
Speed Control and Adjustment.................................................................................. 15
Forward ..................................................................................................................... 15
Backward................................................................................................................... 16
Edge Cutting / Offset Cutting / Return....................................................................... 17
Back to Reference Function ...................................................................................... 17
Perforation Point Selection........................................................................................ 18
Cutting Exit................................................................................................................ 18
Frame Function ......................................................................................................... 19
PART OPTIONS ........................................................................................................... 20
[F1] Mirror.................................................................................................................. 20
Angle Adjustment ...................................................................................................... 21
Array.......................................................................................................................... 22
Zoom in/out................................................................................................................ 26
Select row/number..................................................................................................... 26
Operation after select row/number ............................................................................ 27
Revert........................................................................................................................ 27
MANUAL FUNCTION.................................................................................................... 28
Fixed Moving Function .............................................................................................. 28
Continuous Moving Function..................................................................................... 29
Fixed distance moving............................................................................................... 29
Breakpoint Recovery................................................................................................. 29
FILE OPERATION ........................................................................................................ 30

Files in the Hard Disk ................................................................................................ 30
Files in the U Disk...................................................................................................... 30
Search File ................................................................................................................ 31
Edit Code................................................................................................................... 31
New Code.................................................................................................................. 31
Compile Code............................................................................................................31
PARAMETER SETTING............................................................................................... 32
Common Parameters ................................................................................................ 32
Flame Parameters..................................................................................................... 33
Plasma Parameters................................................................................................... 34
System Parameters................................................................................................... 36
Parameter Import....................................................................................................... 38
Parameter Export ...................................................................................................... 38
Save Parameters....................................................................................................... 38
DIAGNOSIS FUNCTION............................................................................................... 39
Diagnosis Interface Index.......................................................................................... 40
Output Diagnosis....................................................................................................... 41
Key-Press Diagnosis................................................................................................. 42
System Self-Check.................................................................................................... 43
Date and Time...........................................................................................................44
SHAPES ....................................................................................................................... 45
Choose Graph........................................................................................................... 46
G, M Code Guide....................................................................................................... 47

1
1
INTRODUCTION
The quality and reliability of the components assembled on a Baileigh Industrial Holdings LLC
machine guarantee near perfect functioning, free from problems, even under the most
demanding working conditions. However, if a situation arises, refer to the manual first. If a
solution cannot be found, contact the distributor where you purchased our product. Make sure
you have the serial number and production year of the machine (stamped on the nameplate).
For replacement parts refer to the assembly numbers on the parts list drawings.
Our technical staff will do their best to help you get your machine back in working order.
In this manual you will find: (when applicable)
•Safety procedures
•Correct installation guidelines
•Description of the functional parts of the machine
•Capacity charts
•Setup and start-up instructions
•Machine operation
•Scheduled maintenance
•Parts lists
GENERAL NOTES
After receiving your equipment remove the protective container. Do a complete visual
inspection, and if damage is noted, photograph it for insurance claims and contact your
carrier at once, requesting inspection. Also contact Baileigh Industrial Holdings LLC and inform
them of the unexpected occurrence. Temporarily suspend installation.
Take necessary precautions while loading / unloading or moving the machine to avoid any
injuries.
Your machine is designed and manufactured to work smoothly and efficiently. Following proper
maintenance instructions will help ensure this. Try and use original spare parts, whenever
possible, and most importantly; DO NOT overload the machine or make any modifications.
Note: This symbol refers to useful information throughout the manual.

2
2
SAFETY INSTRUCTIONS
LEARN TO RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol. When you see this symbol
on your machine or in this manual, BE ALERT TO THE
POTENTIAL FOR PERSONAL INJURY!
Follow recommended precautions and safe operating practices.
UNDERSTAND SIGNAL WORDS
A signal word –DANGER,WARNING,or CAUTION –is used with the safety alert symbol.
NOTICE, which is not related to personal injury, is used without a symbol.
DANGER: Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE: Indicates a situation which, if not avoided, could
result in property damage.
IMPORTANT
PLEASE READ THIS OPERATORS MANUAL CAREFULLY
It contains important safety information, instructions, and necessary operating procedures.
The continual observance of these procedures will help increase your production and
extend the life of the equipment.
DANGER
WARNING
CAUTION
NOTICE