Bali SRGF11605 User manual

Questions, problems, missing parts or needing replacement parts?
Before returning to your retailer, call our customer service department at 1-866-814-0585,
8 a.m. to 8 p.m., EST Monday to Friday.
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
Do not store or use gasoline or
other flammable vapors and liquids
in the vicinity of this or any other
appliance.
DANGER
WARNING
WARNING: For Outdoor Use
Only.
CAUTION:
Installer: Leave the User Manual to the
user for future use.
Consumer: Please keep this Manual
for future reference.
Read the instructions before use. This
appliance must be installed in accordance
with such regulations as are in force.
User Manual
An LP cylinder not connected for use
must not be stored in the vicinity of
this or any other appliance.
Square Gas Fireplace
Model# SRGF11605
Item# 11875024
TM

Square Gas Fireplace
SRGF11605
50,000 BTU/h
LP
20 lb. LP-gas cylinder
Max. 250 PSI, MIN 5 PSI
2.18 mm
11 inches water column
•Do not try to light the appliance.
•Do not touch any electrical switch; do not use any phone in the vicinity of this product.
•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
•If you cannot reach your gas supplier, call the fire department.
WARNING
CARBON MONOXIDE HAZARDS
: Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Read the installation, operation
and maintenance instructions thoroughly before installing or
servicing this equipment.
WHAT TO DO IF YOU SMELL GAS?
Installation and service must be performed by a qualified installer, service agency or gas
supplier.
!
WARNINGS AND CAUTIONS
This appliance can produce carbon monoxide which
has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such
as a camper, tent, car or home.
2

CONTENTS...................................................................................................................................3
WARNINGS AND CAUTIONS.............................................................................................1-2, 4-5
PREPARATION.............................................................................................................................5
EXPLODED VIEW.........................................................................................................................6
PARTS AND HARDWARE............................................................................................................7
ASSEMBLY INSTRUCTIONS..................................................................................................8-13
INSTALLATION INSTRUCTIONS...............................................................................................14
OPERATION..........................................................................................................................15-17
LOCATING HEATER FOR USE..................................................................................................18
MAINTENANCE AND STORAGE..........................................................................................19-20
TROUBLESHOOTING.................................................................................................................21
WARRANTY INFORMATION......................................................................................................21
CONTENTS
3

IMPORTANT SAFETY INFORMATION
•The installation must comform with local codes or, in the absence of local codes, with
the CAN/CGA-B 149.2, Propane Installation Code.
•Always place the appliance on a firm and level surface.
•Do not burn solid fuels in this gas appliance.
•Use the appliance outdoors in a well-ventilated space only, not in a building, garage, or any other
enclosed area.
•When using the appliance, keep the appliance area clear and at least 50 inches from combustible
materials, gasoline and other flammable liquid and vapors. Certain items or materials, when stored
under the appliance or nearby, will be subjected to radiant heat and could be seriously damaged.
•
Inspect the gas connections of appliance prior to each use. Do not operate the unit if there is a gas
•
Inspect the hose before each use of the appliance. The hose assembly must be replaced prior to the
appliance being put into operation if there is evidence of excessive abrasion or wear or if the hose is
damaged. The replacement hose assembly shall be that specified by the manufacturer.
leak. A qualified service person should inspect the appliance annually.
•Alert children and adults to the hazards of high surface temperatures and keep them away
to avoid burns or clothing ignition.
•Carefully supervise children and pets when they are near the appliance.
•Replace any guard or other protective device removed for servicing.
•Do not hang clothing or other flammable materials on or near the appliance.
•Do not use the appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.
•
•
Use only a cylinder supply system arranged for vapor withdrawal, and the cylinder must include a
•The LP-gas supply cylinder to be used must be: Constructed and marked in accordance with the
Specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT); or the Standard
for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission,
CAN/CSA-B339, as applicable;
The LP-gas supply cylinder to be used must be provided with a listed overfilling prevention device;
and provided with a cylinder connection device compatible with the connection for the appliance.
collar to protect the cylinder valve.
•This appliance requires 20 lb (9.07 kg) LP gas supply cylinder.
•The burner must be replaced prior to the appliance being put into operation if it is evident that the
burner is damaged. The replacement burner shall be that specified by the manufacturer.
•Installation and repair should be done by a qualified service person. The appliance should
be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners,
and circulating air passageways of the appliance be kept clean.
WARNINGS AND CAUTIONS
4

This appliance is designed to operate with a standard 20 Ib (9.07 kg) propane cylinder with approved
cylinder connection.
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES:
Before beginning assembly of product, make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Perform a leak test with a soapy solution:
1. To check gas connections.
2. After connecting a new cylinder.
3. Upon re-assembly after disassembly.
WARNINGS AND CAUTIONS
PREPARATION
TOOLS NEEDED: (NOT INCLUDED)
Philips screwdriver
Estimated time for assembly: 30 minutes with 2
adults.
5

EXPLODED VIEW
1
2
3
4
67
8
11
13
12
14
5
9
10
15
9
9
16
6

AA
BB
CC
DD
Parts Description Quantity Picture
PARTS AND HARDWARE
M6x20 Bolt Assembly
M5x16 Bolt
ST4.2x10 Bolt
M4x10 Bolt
28 pcs
8 pcs
4 pcs
3 pcs
Lid
Fire bowl assembly
Control panel assembly
Table top panel
Left panel
Rear panel
Right panel
Part QuantityDescription Part QuantityDescription
1
2
3
4
5
7
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
6
Support leg A
Foot pad
Strengthening bar
Door
Cylinder holder assembly
Door magnet
Cylinder locking bolt
8
9
10
11
12
13
14
15
3 pcs
4 pcs
2 pcs
1 pc
1 pc
1 pc
1 pc
Support leg B
16 1 pc
1 bagLava rocks
7

Turn the assembled table top over, and then attach three
support legs A (9) and one support leg B (16) to the table
top panel (5) with 16 M6x20 bolt assemblies (AA).
Make sure the support leg B (16) with the door magnet(14)
is at the left of the control panel as shown in the illustration.
Half-tighten 16 M6x20 bolt assemblies (AA) on the table
top panel (5) during this procedure.
AA M6x20 Bolt Assembly 16 pcs
Choose a soft and level location for the assembly. Remove all parts from the packaging, and check for missing parts.
If there are missing parts, please contact customer service.
BB M5x16 Bolt 4 pcs
Attach two strengthening bars (11) to the four support legs
(9 and 16) with 4 M5x16 bolts (BB).
ASSEMBLY INSTRUCTIONS
BB
9
AA
5
3
9
16
16
14
9
9
11
9
99
16
8

Step 4
Hardware Used
Fig. 4
Step 3 Fig. 3
BB M5x16 Bolt 4 pcs
Attach the cylinder holder assembly (13) to two strengthening
Make sure the cylinder locking bolt (15) on the cylinder holder
Screw the cylinder locking bolt (15) to the cylinder holder
assembly (13) as shown in the illustration.
assembly (13) is on the same side as the door magnet (14),
and that the cylinder holder ring on the cylinder holder
assembly (13) is far away of the control panel.
bars (11) with 4 M5x16 bolts (BB).
ASSEMBLY INSTRUCTIONS
13
15
BB
11
11
13
13
15
14
9

Step 5 Fig. 5
Attach the right panel (8) to the 2 support legs (9 and 16) with
4 M6x20 bolt assemblies (AA).
Make sure the control panel on the control panel assembly (4)
fits the position on the right panel (8).
Do not fully tighten the hardware until the entire step is
completed.
ASSEMBLY INSTRUCTIONS
AA
Thermocouple
Electrode
wire
Grounding
wire
DD
8
8
8
4
16
Hardware Used
AA M6x20 Bolt Assembly 4 pcs
9
Step 6 Fig. 6
Attach the control panel assembly (4) to the right panel (8)
with 2 pcs M4x10 bolts (DD).
Attach the grounding wire to the control panel assembly (4)
and the right panel (8) with 1 pc M4x10 bolt (DD).
Connect the thermocouple to the valve and insert the
electrode wire into the igniter under the control panel tightly.
Hardware Used
DD M4x10 Bolt 3 pcs
10

ASSEMBLY INSTRUCTIONS
AA
AA
7
9
9
6
6
7
8Fig. 8
Attach the left panel (6) to the 2 support legs (9) with
4 M6x20 bolt assemblies (AA).
Do not fully tighten the hardware until the entire step is
completed.
AA M6x20 Bolt Assembly 4 pcs
7Fig. 7
Attach the rear panel (7) to the 2 support legs (9) with
4 M6x20 bolt assemblies (AA).
Do not fully tighten the hardware until the entire step is
completed.
AA M6x20 Bolt Assembly 4 pcs
11

Attach the door panel (12) to the support leg (9) with
4 ST4.2x10 bolts (CC).
After that, tighten the16 M6x20 bolt assemblies (AA) on the
table top panel (5) shown on step 1.
9Fig. 9
10 Fig. 10
Place the lava rocks (2) (max. 7.7 lb/3.5 kg) onto the fire bowl
assembly (3).
CC
ASSEMBLY INSTRUCTIONS
CC
9
2
3
5
12
ST4.2x10 Bolt 4 pcs
12

Place the lid (1) onto the table top panel (5) when the fireplace
is not in use.
11
Unscrew the battery compartment cap on the control panel,
install one AAA 1.5 V battery (not included) with the anode
end of the battery located towards the battery compartment
cap.
Replace the battery compartment cap into position.
12
11
ASSEMBLY INSTRUCTIONS
1
1
5
12
13

13
3. Open the door panel (12) and place the cylinder into the cylinder
holder assembly (13). Turn the cylinder clamp screw clockwise to
secure the gas cylinder. (Fig. 13)
LAVA rocks (max, 7.7 lb/3.5 kg)
fireplace
fireplace
fireplace.
fireplace.
14
14
15
16
15 P2
P1
16
Tighten
regulator & cylinder
connection
INSTALLATION INSTRUCTIONS
12 13
14
fireplace ona
the fireplace on a level,

WARNING: DO NOT ATTEMPT TO OPERATE THE APPLIANCE UNTIL YOU HAVE READ AND
UNDERSTAND ALL PRECAUTIONS . FAILURE TO DO SO CAN RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, OR DEATH.
WARNING
WARNING
WARNING
FOR YOUR SAFETY:
DO NOT touch or move gas appliance
for at least 45 minutes after use.
Lighting operations should comply
with Lighting Instruction section.
Improper lighting operations will
cause serious injury and explosion.
Before turning gas supply ON
Your
fire pit was designed and approved for OUTDOOR
USE ONLY. DO NOT use it inside a building or any other
enclosed area.
Make sure surrounding areas are free of combustible
materials, gasoline, and other flammable vapors or liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris.
Be sure any component removed during assembly or
servicing is replaced and fastened prior to starting.
FOR YOUR SAFETY:
WARNING!
Do not use an open flame to check for leakage.
Do not smoke during testing.
Do not test indoors.
A leak check must be performed whenever the gas
cylinder is replaced.
NOTE:
U
se only the pressure regulator supplied with this fire pit.
Replace them with those specified by the manufacturer
only.
OPERATION
If at any time you are unable to
light burner and smell gas, wait five
minutes to allow the gas to dissipate
before attempting to light the gas
appliance. If after 1 minute you
are unable to light theburner, wait
5 minutes and allow flammable
vapors to dissipate before
attempting to light the gas appliance.
15

ATION
Before Lighting
The gas fire pit should be thoroughly inspected before each
use, and by a qualified service person at least annually.
If relighting a hot gas fire pit, always wait at least 5 minutes.
Lighting instructions
1. Make sure control knob is in the
"OFF" position.
2. Turn LP cylinder gas valve to fully
open position.
3. Press down control knob and turn it
counter clockwise to "MIN/IGNITE"
position, at the same time push in the ignition
button and keep the button depressing until
light the burner.
4. If the burner is lit, keep pressing down
the control knob for 1 minute before
releasing it.
5. If the burner is not lit, press down the
control knob and turn clockwise to "OFF" position, repeat from step 3 after 5 minutes.
6. When burner is lit, turn the control knob to the desired heat output position between "MIN"
and "MAX".
7. Press down and turn the control knob clockwise to "OFF" position to shut down the appliance.
Turn off cylinder gas valve.
Flame Characteristic
Normally the burner flame is yellow.
If the burner flame is blue and very small, please check the
erehtfI.ytpmeroe,russerpsagwolebyamtisa,rednilycsag
is enough gas in the cylinder, please contact customer service
to change the burner of the gas fire pit.
If flames lift away from burner or backfire happens, or produce
thick black smoke, the fire pit should be turned off immediately.
The fire pit should not be operated again until the unit is serviced
and/or repaired by a qualified service technician.
WARNING: DO NOT ATTEMPT TO OPERATE THIS HEATER UNTIL YOU HAVE READ
AND UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT IN
PROPERTY DAMAGE,SERIOUS INJURY,OR DEATH.
OPERATION
16
MIN/IGNITE (Min./allumer)
OFF (Arrêt)
MAX .
IGNITOR (bouton d'allumage)

CAUTION:AVOID INHALING FUMES EMITTED FROM THE GAS APPLIANCE'S FIRST
USE. SMOKE AND ODOR FROM THE BURNING OF OILS USED IN MANUFACTURING
WILL APPEAR. BOTH SMOKE AND ODOR WILL DISSIPATE AFTER APPROXIMATELY
30 MINUTES THE GAS APPLIANCE SHOULD NOT PRODUCE THICK BLACK SMOKE.
NOTE:
The burner may be noisy when initially turned on. To eliminate
excessive noise from the burner, turn the control knob to the
.derisedtaehfolevelehtotbonkehtnrut,nehT.noitisopNIM
Operation pressure checked:
If the flame is very small, this is because the supply pressure is
not enough. Please refill LP gas cylinder.
Re-light:
Turn the control knob to the "OFF " position.) 1
2)
3) Repeat steps beginning with step 3 of the lighting instruction.
Shut down instructions:
1) Push in and turn control knob clockwise to the "OFF" position.
2)
2) Turn LP cylinder valve to the "OFF" position.
The Event of Gas Leakage:
1) Turn the control knob to the "OFF" position.
3) Wait 5 minutes to allow gas to dissipate.
4) If odor continues, immediately call the gas supplier.
WARNING : Gas appliance will be hot after use.
Handle with extreme care.
Wait five (5) minutes before attempting to relight appliance.
Turn LP cylinder gas valve clockwise to the OFF position when
appliance is not in use.
OPERATION
MIN/IGNITE (Min./allumer)
MAX .
OFF (Arrêt)
MIN/IGNITE (Min./allumer)
MAX .
OFF (Arrêt)
17

58
36 36
17
17
FIREPLACE
LOCATING HEATER FOR USE
fireplace
fireplace
18

T
FOR YOUR SAFETY ;
DO NOT touch or mov the gas
appliance for at least 45 minutes
after use.
Allow all burner elements to cool
before touching.
WARNING:
NOTE:
In a salt-air environment (such as
near an ocean), corrosion occurs
more quickly than normal.
Frequently check for corroded
areas and repair them promptly.
NOTE:
Wait until gas appliance is cool before
covering.
CLEANING AND MAINTENANCE :
To enjoy years of outstanding performance from your
gniwollofehtmrofrepuoyerusekam,ecalperifsag
maintenance activities on a regular basis:
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use
flammable of corrosive cleaning agents.
While washing your unit, be sure to keep the area
around the burner dry at all times. If the gas control is
exposed to water in any way, do NOT try to use it. It
must be replaced.
Keep the appliance area free and clean from combustible
Check if there are cracks or worn sections on the hose. If
yes, please call our customer service to replace the hose.
materials, gasoline and other flammable vapors and
liquids; not obstructing the flow of combustion and
ventilation air; keeping the ventilation opening(s) of the
cylinder enclosure free and clear from debris.
Gas fireplace does NOT reach the desired temperature.
Gas fireplace glow is excessively uneven.
Gas fireplace makes popping noises.
At least once a year, the unit should be inspected for
the presence of spiders, spider webs or other insects.
Air flow must be unobstructed. Keep controls, burner,
and circulating air passageways clean. Signs of possible
blockage include:
Spiders and insects can nest in burner or orifices. This
dangerous condition can damage gas fire pit and render
it unsafe for use. Clean burner holes by using a heavy-duty
pipe cleaner. Compressed air may help clear away
smaller particles.
MAINTENANCE AND STORAGE
19

NOTE:
Wait until the appliance is
cool before covering.
Store the fire pit indoors during the winter if it will be subjected to
freezing temperatures.
Disconnect and remove the cylinder from the appliance before the
appliance can be stored indoors.
STORAGE
Turn the control knob to the "OFF" position.
,esuretfanwodloocotfireplaceehtrofsetunim54tsaeltawollA
Turn LP cylinder to the "OFF" position.
Take out the battery from the battery compartment during
periods of extended inactivity or when transporting.
and then turn regulator counterclockwise to disconnect the regulator
from cylinder, turn the cylinder clamp screw counterclockwise to
loose the cylinder and remove the cylinder.
Cylinder must be stored outdoors in a well-ventilated area out of
the reach of children. When the cylinder is disconnected,tightly
,gnidliubanitierotstonoddna,sgulpevlavdedaerhtehtllatsni
garage or any other closed area.
You may store product indoors ONLY if the cylinder is
disconnected and removed.
,slairetamelbitsubmocmorfeerfdnaraelcaerafireplaceehtpeeK
gasoline and other flammable vapors and liquids.
secafrusroiretxetcetorpottirevocfireplaceehtgnisutonerauoyfI
and to help prevent build up in air passages.
Store gas fireplace in an area sheltered from direct contact with
sleet, hail, snow, dust and debris).n,iarsahcus(rehtaewtnemelcni
A qualified service person should install and repair the fireplace and
inspect it annually.
It might be necessary to clean this fireplace frequently. You must
passageways clean.
MAINTENANCE AND STORAGE
keep the control compartment, burner and circulating air
20