Ballard Designs Mallorca AO127 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 12-16-2019 Page 1 of 4
PRODUCT NAME: Mallorca Fountain
ITEM NUMBER: AO127
ASSEMBLED DIMENSIONS : 28 1/2”H x 19 3/4”W x 10”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 4
Ltr.
A 1
C
Qty. Included Hardware
Ltr.
1
Qty. Component
NO TOOLS REQUIRED
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Fountain
B 1
Splash Guard
Pump
with attached power
cord

Back
Front
Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(A)
STEP 1: ATTACH PUMP / PULL CORD
Place Fountian (C) on clean, level surface. Set Flow Control on Pump (A) to MAXIMUM (+) setting
then insert Tube into top opening (Tube located in basin). Unwind, feed and pull power cord through
back of Fountain. Finally, place Splash Guard (B) into basin, screen facing up.
STEP 2: ADD WATER / CONNECT ELECTRICAL
Place Fountain (C) in location for use then fill basin with clean water. Plug Pump (A) into grounded
(preferably GFCI) outlet and adjust spigot/pump to desired water flow. (NOTE: As water flows into
basin, there will be some splash in area around Fountain. Protect sensitive surfaces in immediate
area.
Plug Pump into a GFCI Outlet or Circuit
Electrical Shock Hazard
Do Not Alter Plug or Cord
WARNING
(C)
Tube
(B)
C
l
e
a
n
,
C
o
o
l
,
F
r
e
s
h
W
a
t
e
r
O
n
l
y
(C)

Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MAINTENANCE
1. Keep water clean.
2. Periodically clean fountain and pump to prevent mineral deposits and contamination.
3. Disconnect power and empty basin during long periods of non-use.
4. Protect from freezing. Do not use fountain in area where temperature can
drop below 41 degrees. Permanent damage may result.
WARNING
1. To reduce risk of electrical shock, plug into a GFCI outlet or circuit.
2. Prior to installation, inspect cord for damage and do not use if insulation is missing or
compromised.
3. Periodically check cord for damage and replace if necessary.
4. Do not remove grounding pin from plug.
5. Do not exceed voltage rating listed on pump.
CAUTION
1. Keep cord away from high temperature or heat source.
2. Keep fountain out of reach of children.
3. In a freezing temperatures, remove water from basin, pump and supply tube.
Store entire fountain indoors, protected from freezing.
4. Disconnect electrical source when handling pump.
5. Do not permit pump to run dry.
6. Do not lift pump by cord.
7. Do not pump heated liquids.
8. Operate using fresh water only.
9. Keep pump fully submerged to ensure proper operation and cooling.
TROUBLESHOOTING
1. Ensure pump’s flow control switch is set to MAXIMUM (+) before operating. Once flow
is established it can be adjusted downward if desired.
2. If pump is running, but there is no water flow check the pump’s flow control and/or see
that pump is fully submerged or if the tube is kinked or pinched.
3. If pump is running, but there is no water flow, the pump is fully submerged, flow
control is set to maximum and the hose is not kinked or pinched, unplug pump,
disconnect supply tube and lift pump out of water. Clean supply tube inside and out
as well as clean away any debris from around outside of pump.