Bambi BC-62 User manual

Instruction
Manual

2
Thank you for purchasing our BC-62 baby monitor. Your unit has been
manufactured and checked under the strictest possible quality control to ensure
that each monitor leaves the factory in perfect condition. If in the unlikely event you
find any defects or have any problem, please contact your dealer, our branch or
service center.
Please read this manual carefully to obtain maximum performance & extend -
ed service life from the unit.
Features
- Full digital technique operating in the 902.000MHz---928.000MHz with zero
interference - Automatic search and hop to free channel
- Operating range of 800m in open space
- Low radiating power (only 8% of normal DECT and 40% of ECO DECT)
- Automatic power reduction system further reduce radiation level to half when
baby unit and parent unit are close to each other
- Night light with adjustable intersity on baby’s unit
- Audio and visual alert for out-of-range on parent unit
- LED level meter on parent unit
- Low battery warning on both baby and parent unit
- Adjustable microphone sensitivity on baby unit
- Vibration alert on parent unit

3
WARNING
The BC-62 baby monitor should not be regarded as a medical device.
Premature babies or those considered to be at risk should be under the supervision
of your doctor or health personnel.
Direct supervision of your baby at a regular interval by a responsible adult is
strongly recommended in addition to using the BC-62.
DIGITAL TECHNOLOGY AND APRS
This baby monitor employs full digital technology with zero interference.
The unit can automatically select free channel or hop to free channel during
communication to avoid interference from other electronic devices. In addition,
thanks to the Automatic Power Reduction System (APRS) which senses the
distance between baby and parent unit and automatically reduces the emission
power from baby unit when the two units are in close vicinity. The level of radiation
to baby is greatly reduced.

4
POWER SUPPY
(A) Baby Unit
1. Operation from batteries
Pr ess down the lock button and slide open the battery door in direction as
shown.
Insert three pieces AAA size (UM-4) alkaline batteries into the compart -
ment. Observe correct polarities indication.
N.B. For best performance, do not mix use old and new batteries or
alkaline and rechargeable batteries.
2. Operation using AC adapter
The baby unit can be operated on AC mains using the supplied 5V AC
adapter. Connect the output plug of AC adapter to USB port 12 of the baby
unit, make sure the polarity is correct. The battery will be cut off once the
AC adapter’s output plug is inserted into the USB port 12 .
12

2. Charging up the Lithium rechargable battery
Connect the output plug of the supplied 5V AC adapter to the USB port 22
of the unit, make sure the polarity is correct. With the parent unit being
switched off, the power on icon 1 8 will start flashing red, indicating the
battery is being charged. Once the battery is fully charged up (normally it
takes around 3 hours), the indicator 18 turns steady green. Now the parent
unit can be switched on for operation. Either you can disconnect the AC
adaptor or keep connecting will cause no damage to the battery. In the
latter case, when the battery is being consumed and voltage falls to a
certain level, the AC adapter will automatically start charging up the battery
again.
5
(B) Parent unit
1. Operation from battery pack
The Li polymer battery pack is already installed in the unit. To exchange
battery pack, press and open the battery cover, remove the belt clip in the
direction as shown, take out the battery pack and disconnect from socket.
Note : Before using the parent unit for the first time, charge up the Li
battery pack for at least three hours. Besure to switch off the unit before
charging.
Even without the Li battery pack being installed, the unit can still
operate normally once connecting to the AC adapter, while the power on
icon will always stay steady green.
CAUTION : BESURE THE BATTERY IN THE PARENT UNIT IS
RECHARGEABLE TYPE BEFORE CONNECTING TO AC ADAPTER,
OTHERWISE EXPLOSION MAY RESULT.
22
18

6
CONTROLS LAYOUT
7
8
6
1
11
2
4
18
19
17
13
14
16
15
22
20
21
5
3
12
9
10
BABY UNIT
PARENT UNIT
1
2
3
4
5
6
7
8
9
10
11
Power On/Off button
Microphone Sensitivity Down adjustment button
Microhone Sensitivity Up adjustment button
Night Light intensity adjustment button
Night Light VOX control button
Night Light
Power On/Battery low icon
Transmit icon
Night Light VOX icon
Micophone always ON icon
Microphone
USB port
Power On/Off button
Volume down button
Volume up button
Vibration button
Visual level meter/Out-of-range icon
Power On/Battery Low/Charging icon
Vibration icon
Speaker mute icon
Speaker
USB port
12
13
14
15
16
17
18
19
20
21
22
Model:A014302
IC:12292A-A014302

7
PAIRING
This process is to match the parent unit with baby unit so that they can
communicate with each other while no other devices (even baby monitor of identical
model) can interfere with you or receiving your signal.
The baby and parent unit are already paired with factory preset code when they are
shipped from factory. However, we recommend to perform pairing again in case
interference is experienced:
1. First press and hold the button 15 of parent unit.
2. Press the power ON-OFF button 13 and wait until the power on icon 18
starts flashing green. Release both buttons 13 & 15 .
3. Now press and hold the button 11 of baby unit.
4. Press the power ON-OFF button 1 and wait until the power on icon
7 starts flashing green. Release both buttons 1 & 11 .
5. Now short press the power ON-OFF button 1 of baby unit.
6. If pairing is successful, the power on icons 18 & 7 on both baby & parent
unit should stop flashing, at the same time, 2 beep sound will be heard from the
parent unit.
7. Long press buttons 1 & 13 to switch off both baby and parent units and then
switch them on again, the baby monitor is now ready for operation.
8. In case the baby and parent unit cannot communicate with each other, repeat
steps 1 - 7 again.

OPERATION
Baby unit
1. Long press the power ON/OFF button 1 for 3 sec to switch on the unit. The
power on icon 7 should light up steady green. To turn off, long press the
button 1 again.
2. Place the unit about 1 m from the crib with the microphone 11 facing towards the
baby.
3. Adjust the microphone sensitivity using the button 2 and button 3 such
that the unit will be set to transmit whenever the microphone 11 picks up a sound at
your desirable loudness level. The intensity of night light 6 will change during
adjustment. The higher the intensity, the more sensitive is the microphone 11 to
sound. There are total 5 levels of microphone sensitivity. When the maximum level
is reached, further press of the button 3 will set the unit into continuous transmis-
sion mode (i.e. the unit will transmit even without detecting a sound) and the000
icon 10 will light up steady green.
4. Once the unit is in transmit mode, the transmit icon 8 will light up green. The
unit will return to standby mode a few seconds after the microphone 11 stops picking
up any sound and the transmit icon 8 will go off. Except when the unit is set in
continuous transmission mode, the transmit icon 8 will stay steady on.
5. The night light 6 can be set permanently ON by pressing the button 4 . Each
press of button 4 will increase the level of light intensity ( maximum 5 levels).
The night light 6 can also be set to VOX (voice activated) by pressing button
5 . Under VOX mode, the icon 9 will light up and night light 6 will be
switched on once the microphone 11 detects a sound and automatically fade off a
few seconds after the sound stops.
5. The condition of the battery is shown by the power on/low battery icon 7 . When
the battery level becomes running low, the power on/low battery icon 7 turns
red. Replace with new battery or use the supplied AC adapter.
Parent unit
1. Long press the power ON/OFF button 13 for 3 sec to switch on the unit. The
power on icon 18 should light up steady green. To turn off, long press the
button 13 again.
2. Place this unit at a reasonable distance away from the baby unit to avoid feedback.
ON
Too close a distance will create a screeching sound at the speaker 21.
8

3. Once it receives a signal from the baby unit, the visual level meter 17 will light up.
The number of segments being lighted up vary along with the sound. This feature is
useful in case the parents prefer to turn down the speaker volume to keep the
environment quiet.
4. The speaker volume can be adjusted using the button 14 and button 15 .
Each press of button will change the volume by 1 step which is correspondingly
indicated by the visual level meter 17 . There are total 5 volume levels, more
segments shown in visual level meter 17 means higher volume. When the volume
setting is at minimum, further press of button 14 will cause the speaker 21 to be
totally muted with the icon 20 being lighted up.
5. This unit is equipped with a vibration alert. Press the button 16 and the icon
19 will show up. Once the received baby’s voice is loud enough, the vibrator starts
to function. This feature is useful when the parent is working under noisy environ-
ment (e.g. vacuum cleaning). To save battery power, it is recommended not to use
the vibration alert frequently. To switch off vibration, press the button 16 again
and the icon 19 goes off.
6. Once this unit is beyond the communication range of baby unit for over 30 sec, an
out of range alarm will be heard together with segments of the visual level meter 17
flashing to alert the parents. The alarm sound is independent of whether the speaker
is muted or not. This alarm will go off only when the parent unit falls back within the
communication range of baby unit.
N.B. This alarm will also be heard in case the baby unit is switched off, or its
battery has run down, or its power is cut off, or the pairing is not properly done
between the baby and parent unit.
7. The condition of the Li battery pack is shown by the power on/low battery icon 18.
When battery level becomes running low, the icon 18 turns red and an alarm will
be heard, reminding the parents to charge up the battery using the supplied AC
adapter.
8. Each time the buttons are pressed, a beep tone will be heard. To eliminate this beep
tone, press and hold the button 14 for 2 sec until a second beep tone is heard.
To resume the beep tone, press and hold the button 15 for 2 sec until a beep tone
is heard. Whenever the unit is switched off and then on again, the beep tone will
resume automatically.
9

Use only the supplied AC adapters, use of other adapters may cause damage to
10
STANDARD ACCESSORIES
a. 5V AC adapter x 2
b. Baby unit
c. Parent unit
d. 3.7V Li Polymer rechargeable battery pack
(installed in parent unit)
e. User manual
ab
d e
c
PRECAUTIONS
-
the BC-62 baby monitor.
- When not using the monitor for a long period of time, remove all batteries form the
PU, BU and movement sensor mat to avoid damage due to battery leakage.
- Disconnect the AC adapter form the wall outlet when the monitor is not to be
operated.
- The BC-62 is best performed within a temperature range of -19˚C to +50˚C.
- Do not open the cabinet, no serviceable parts inside.
- The BC-62 should not be exposed to dripping, splashing and that no objects filled
with liquids, such as vases shall be placed on it.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent.
- Batteries ( battery pack or batteries installed ) shall not be exposed to excessive
heat such as sunshine, fire or the like.
- The MAINS plug of an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
- Only use the power supply unit list in the user manual
I
nst ruc tion
M
an ual
Manufacturer:BABYMOOV ALT PARTNERS
Product Name:Digital Baby Monitor
Model No:A014302

TROUBLE SHOOTING GUIDE
11
PROBLEM
Baby Unit
has no
Transmission
Transmission
always on
Out-of-range
alarm
always on
Always
showing low
battery alert
Battery life
is short
Communication
frequently
Interrupted
Too short
Communication
range
POSSIBLE CAUSE
- Mic sensitivity is too low
- Battery has run down or AC
adapter improperly connected
- Mic Sensitivity is too high
- Unit is set to continuous
transmission mode
- Baby unit’s battery has run
down
- Distance between baby and
parent unit exceeds the
operating range
- Pairing is not successful
- Battery has run down
- Battery pack is damaged
- Night light is permanently
switched on
- Vibration alert is switched on
- Baby unit is located near
other electrical appliances
- Many steel structures
between baby & parent unit
- Baby unit battery has run
down
SOLUTION
- Adjust mic sensitivity higher using
button 3
- Replace with new battery or
check connection
- Adjust mic sensitivity lower using
button 2
- Set the unit to become voice
activated
- Replace with new battery or use
AC adapter
- Move the baby & parent unit
closer together
- Perform pairing again
- Recharge battery using AC
adapter ( parent unit )
- Replace with new battery or use
AC adapter ( baby unit )
- Replace with new battery pack
- Switch off night light or set to
VOX operate
- Switch off vibration alert
- Remove the electrical appliances
or re-locate the baby unit far
away from source of interference
or perform pairing again.
- Re-locate baby or parent unit
- Replace with new battery or use
AC adapter

12
All European Countries except Austria, Georgia, Greece, Norway, Russian,
Federation, Spain, Sweden, The Netheriands, Ukaine.

13

FCC
Caution: The user is cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
IC:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
14