Banner RSD1 Series User manual

Quick Start Guide

Remote Display and Conﬁguration Tool

To view or download the latest technical information about this product, including speciﬁcations, dimensions, accessories, and

wiring, see

www.bannerengineering.com

. Search 199621 to view the Instruction Manual. To check RSD1 compatibility with a

sensor, reference the sensor speciﬁc literature.

• Allows for conﬁguration of remote sensor heads

• Easy to set up and use with a 2-line, 8-character display

• Ability to display live distance measurement

• Ability to save up to 6 unique conﬁgurations

• Not required for continuous operation of conﬁgured sensor(s)

Models

Model Output A and B Connection

RSD1QP Conﬁgurable Integral 150 mm (6 in) PVC cable with 5-pin M12/Euro-style quick disconnect

Overview

The RSD1 remote display is designed to provide easy sensor conﬁguration and monitoring with the ability to copy settings between

sensors.

Features and Indicators

Output A

LED Indicator

Power

LED Indicator

Output B

LED Indicator

Display

Push Buttons

Figure 1. RSD1 Display Features

Three LED indicators on the RSD1 provide ongoing

indication of the connected sensor status.

Output A LED Indicator

Solid Amber = Output A On

Off = Output A Off

Power LED Indicator

Solid Green = Normal Operation, Power On

Output B LED Indicator

Solid Amber = Output B On

Off = Output B Off

RSD1 Buttons

Use the RSD1 buttons Down, Up, Enter, and Escape to view or change RSD1 settings and information and to program a

connected sensor.

Down and Up Buttons

Press Down and Up to:

• Navigate the menu systems

• Change programming settings

When navigating the menu systems, the menu items loop.

Press Down and Up to change setting values. Press and hold the buttons to cycle through numeric values. After

changing a setting value, the value slowly ﬂashes until the change is saved using the Enter button.

RSD1 Remote Display

Original Document

199622 Rev. B

4 September 2018

199622

Enter Button

Press Enter to:

•Conﬁrm selection

• Save changes

In the RSD1 Menu, a check mark in the lower right corner of the display indicates that pressing Enter accesses a

submenu.

Press Enter to save changes. New values ﬂash rapidly, and the sensor returns to the parent menu.

Escape Button

Press and hold Escape for 4 seconds to:

• Access the RSD1 Menu while in Run mode

Press Escape to:

• Leave the current menu and return to the parent menu

Important: Pressing Escape discards any unsaved programming changes.

In the RSD1 Menu, a return arrow in the upper left corner of the display indicates that pressing Escape returns to the

parent menu.

Press and hold Escape for 2 seconds to return to Run mode from the RSD1 Menu.

Programming a Sensor with the RSD1

When connected to a sensor and in Run Mode, the RSD1 mirrors the connected sensor's display. Program a sensor using the

buttons on the RSD1.

For sensor programming information, reference the literature speciﬁc to the connected sensor.

For more information on the options available in each RSD1 menu, reference the Instruction Manual (199621).

In addition to programming a connected sensor, the RSD1 buttons can be disabled to prevent unauthorized or accidental

programming changes. See the Instruction Manual for more information.

Wiring Diagrams

The following wiring diagrams are examples of different RSD1 outputs. Wiring is dependent on the sensor connected to the

RSD1.

Dual Discrete

shield

12–30 V dc

D1_Out

D2_Out

Input

−

Load

NPN

PNP

* User-configurable PNP/NPN setting

Load

Discrete Analog (Current)

shield

12-30V dc

D_Out

A_Out

Input

–

Load

* User-configurable PNP/NPN setting

4-20 mA

NPN

PNP

Discrete Analog (Voltage)

shield

12-30V dc

D_Out

A_Out

Input

–

Load

* User-configurable PNP/NPN setting

NPN

PNP

0-10V

Note: When connecting a 5-pin sensors to the RSD1, a double-ended 5-pin to 5-pin cordset is optional.

When connecting a 4-pin sensor to the RSD1, a double-ended 4-pin to 5-pin adapter cordset is required.

RSD1 Remote Display

2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 199622 Rev. B

Display Menu Full Map

Diag1

Diag2

Diag3

Run

Mode

Press and hold

> 4 sec.

ENTER

RSD1

If the Config

is Empty... Import

Export

Yes

Delete

Yes

Detail Model

S/N

FW Ver.

Comm Ver.

Comm P/N

Name Edit

New

CONFIG

------

Active Auto

Hi(PNP)

Low(NPN)

Disable

Sensor

RSD1

Type

Yes

Switch

View Normal

Invert

Sleep

Unlock

Oplock

Lock

Yes

Model

S/N

P/N

Diags

Version

Disable

1 min

5 min

15 min

60 min

Name Edit

New

CONFIG

RSD1 Menu = Default values

Config

Confg2

Confg3

Confg4

Confg5

Confg6

RSD in

RSD Disp

RSD Lock

RSD Info

Reset

End

------

If the Config

is Not Empty...

Figure 2. RSD1 Full Menu Map

RSD1 Remote Display

P/N 199622 Rev. B www.bannerengineering.com - Tel: +1-763-544-3164 3

Speciﬁcations

Supply Voltage

Use only with suitable Class 2 power supply

12 V dc to 30 V dc:

• Max. load of 330 Ω for analog current (4 mA to 20 mA)

15 V dc to 30 V dc:

• Max. load of 500 Ω for analog current (4 mA to 20 mA)

Power and Current Consumption

Maximum Power Consumption: < 3.6 W (At 30 V dc, 119 mA) with 2 discrete

outputs at 50 mA load each

Power Consumption, Normal Run Mode with No Load: < 0.6 W (At 30 V dc,

19 mA)

Supply Protection Circuitry

Protected against reverse polarity and transient overvoltages

Output Conﬁguration

Analog output: 4 to 20 mA or 0 to 10 V, depending on sensor

Discrete output rating: Discrete NPN/PNP, depending on sensor

Note: 2 ms output delay with white wire

Output Ratings

Discrete Output: 50 mA maximum (protected against continuous overload

and short circuit)

OFF-state leakage current–PNP: < 10 µA at 30 V

OFF-state leakage current–NPN: < 200 µA at 30 V

Output saturation voltage–PNP outputs: < 3 V at 50 mA

Output saturation voltage–NPN outputs: < 2 V at 50 mA

Analog current output: 330 kΩ max. at 24 V; max. load resistance =

[(Vcc-4.5)/0.02 Ω]

Analog voltage output: 2.5 kΩ min. load resistance

Connection

Integral 150 mm (6 in) PVC cable with 5-pin M12/Euro-style quick

disconnect

Construction

Housing: Polycarbonate

Environmental Rating

IEC IP65

Operating Temperature

–10 °C to +50 °C (+14 °F to +122 °F)

Storage Temperature

–40 °C to +70 °C (–40 °F to +158 °F)

Vibration and Mechanical Shock

All models meet MIL-STD-202G, Method 201A requirements. Also meets

IEC 60947-5-2. Vibration: 10 Hz to 60 Hz maximum, 0.06 inch (1.52 mm)

double amplitude, 10G maximum acceleration per IEC 60947-5-2. MIL-

STD-202G, Method 213B, Condition I (100G 6x along X, Y and Z axes, 18

shocks), with sensor operating. Also meets IEC 947-5-2 requirements: 30G

11 ms duration, half sine wave.

Certiﬁcations

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or

replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not

cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO

BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES

RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT,

STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously

manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the

product is identiﬁed as not intended for such purposes will void the product warranty. Any modiﬁcations to this product without prior express approval by Banner Engineering Corp will

void the product warranties. All speciﬁcations published in this document are subject to change; Banner reserves the right to modify product speciﬁcations or update documentation at

any time. Speciﬁcations and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:

www.bannerengineering.com

RSD1 Remote Display