BARKER AND STONEHOUSE TIVERTON T1VEDINIBULK User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT NOTICE
THIS BOOKLET CONTAINS USEFUL INFORMATION
ABOUT WARRANTY & CARE INSTRUCTIONS.
PLEASE KEEP FOR FUTURE REFERENCE.
TIVERTON 1.3M ROUND DINING TABLE
SKU: T1VEDINIBULK

ASSEMBLY INSTRUCTIONS
2
PARTS LIST
Part Qty Part Name
A 1 Table Top
B 1 Glass
C 2 Leg
D 2 Leg Support
E 1 Parasol Ring, Reducer & Cap
F 8 M6 x 25mm Screw
G 4 M6 x 15mm Screw
H12 Washer
I 1 Allen Key
Ax1 Bx1
Ex1 Dx2
Cx2
Ix1 Fx8 Hx12 Gx4

3
ASSEMBLY INSTRUCTIONS
SAFETY ADVICE - READ BEFORE YOU START:
• Never use power drills when assembling the table.
• Ensure that you read this manual before starting to assemble your table.
• Check that you have all parts from the parts list. Do not throw away any packaging
until you are confident that you have all parts.
• Assemble this product on a soft/flat surface.
• Place the table glass safely to one side until it is required and never lay the glass
on hard or rough surfaces during assembly.
• If you are using the table in conjunction with a parasol, ALWAYS make sure you
have a suitable weighted base to ensure the parasol does not blow over. Incorrect
use of a parasol will void your warranty.
• Always close and remove the parasol from the table when the parasol is not in use.
• It is recommended that two people lift the glass. Ensure you lift with the correct
posture & technique.
• Keep any plastic bags, tools, and fittings away from children and pets.
• After prolonged use we recommend you check all the fittings are tightened
securely.
• Please do not modify this product, use other tools, or substitute parts to build your
item(s), as this will void your warranty.
• Please only use this product for its intended purpose as outdoor furniture within a
residential environment. Failure to do so will void your warranty.
• Barker And Stonehouse holds no responsibility for any damages caused due to
normal wear and tear, incorrect assembly, misuse and/or negligence.
• We reserve the right to make changes for product improvements.
• Please recycle packaging where possible.

ASSEMBLY INSTRUCTIONS
ASSEMBLY
4 5
STEP 1
Loosely secure the leg onto the table top using the M6 x 15mm screws and
washers. Do not tighten any screws at this step.
TOP TIP!
Utilise the outer cardboard
packaging where possible. This
will protect your table when
assembling and prevent damage.
C
A
x1
IGC
x2x1
H
x2
A
x1
I
G
H

ASSEMBLY INSTRUCTIONS
5
ASSEMBLY
C
A
I
G
H
x1
IGC
x2x1
H
x2
STEP 2
Loosely secure the second leg onto the table top using the M6 x 15mm
screws and washers. Do not tighten any screws at this step.

ASSEMBLY INSTRUCTIONS
ASSEMBLY
6 7
STEP 3
Loosely secure the leg support to the inside of the legs using the M6 x 25mm
screws and washers. Do not tighten any screws at this step.
D
x1
IFD
x4x1
H
x4
H F I

ASSEMBLY INSTRUCTIONS
7
ASSEMBLY
STEP 4
Loosely secure the leg support to the inside of the legs using the M6 x 25mm
screws and washers.
D
x1
IFD
x4x1
H
x4
H F I
ITS TIME!
Tighten all the screws with the
provided Allen key

ASSEMBLY INSTRUCTIONS
ASSEMBLY
8 9
STEP 5
Turn the table over. Add the glass to the table top ensuring the suction rings
are flat.
B
x1
B
SAFETY WARNING!
Always lift and secure the glass with
two people.

ASSEMBLY INSTRUCTIONS
9
ASSEMBLY
STEP 6
Position the parasol ring into the centre of the table. Remove the ring reducers
to accommodate the size of your parasol pole. If you are not using a parasol,
cover the parasol ring with the blanket plate.
E
Blanket Plate
Up to 38mm
Parasol
Up to 48mm
Parasol
E
x1
COMPLETE!
Assembly of the table is now
complete!

CARE & MAINTENANCE ADVICE
ASSEMBLY INSTRUCTIONS
10
Please read the below Care & Maintenance tips to help
protect your garden table:
• To prolong the life of the tabletop we recommend you always use place mats and
coasters when putting glasses and plates onto the glass.
• Keep your table away from external extreme heat sources.
• We recommend you always use heat mats when placing hot objects on the
tabletop.
• Be careful not to drop any objects onto the table as this could damage the tabletop.
• We always recommend two people to lift the glass.
• The table is fitted with plastic feet for protection. Never drag the table as this will
accelerate wear and tear on the feet, which is not covered under warranty.
• We recommend cleaning the table with warm, soapy water. You can use a cloth or
a soft-bristle brush with gentle pressure. Never use abrasive cloths or detergents to
clean the glass. Once you have finished, wash off any residue with clean water.
• For optimum glass and rattan protection we recommend a protective cover is used
all year round.
• We recommend clearing any spills quickly when exposed to direct sunlight. Any
clear liquid on the glass will work as a magnifier, the temperature of the sun’s
rays will increase creating an extremely hot heat source which could damage the
rattan. The same applies to leaving a filled drinks glass on the glass tabletop for an
extended period.

ASSEMBLY INSTRUCTIONS
11