Furmanac MiBed Imperial Manual

ASSEMBLY INSTRUCTIONS
Made in EnglandMade in England
Easy set up instructions
for your new Imperial bed
IMPERIAL
DEEP BASE VERSION - 13 inch 3’0 & 2’6
SHALLOW BASE VERSION - 8 inch 3’0 & 2’6
OFFICE CODE:
LEAFLET - IMPERIAL

1. Unpack in the room the bed is
intended to be used, remove all
packaging and dispose of carefully,
keeping polythene out of the reach
of children.
Introduction
and components
The following tools are required for this assembly
1 x Allen Key
1 x 11mm Spanner
1 x Star Screwdriver (also known as a Phillips)
Tools required
Some stages of this Bed Assembly
will require two people to hold and
lift components that maybe heavy.
pLEASE NOTE
2. Place the 2 X slatted K frames
to one side for now, and follow the
next stages until ready to place these
components into the bed frame.
• 1x Head Rail
• 2 x Side Rails
• 1 x Foot Rail
• 2 x K Frames
• 4 x M8 Head Board
Fixing Bolts
• 4 x Country Oak Legs
• 8 x M8 Washers
(to x Head Board)
• 1 x Mattress Retaining Bar
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4
FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
FIXING BOLTS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4
FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
M8 HB WASHERS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
FIXING SCREWS
FOR SECURING
THE K FRAME
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
OAK LEGS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
RETAINER BAR
CONTENTS FOR 8INCH BASE:
• 1x Head Rail
• 2 x Side Rails
• 1 x Foot Rail
• 2 x K Frames
• 4 x M8 Head Board
Fixing Bolts
• 4 X M8 Washers
• 4 x 40mm Black Castors
• 8 x M8 HB Washers
(to x Head Board)
• 1 x Mattress Retaining Bar
• 1 x Allen Key
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4
FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
FIXING BOLTS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4
FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
M8 HB WASHERS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
FIXING SCREWS
FOR SECURING
THE K FRAME
Imperial 13 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
MRB-SMALL-SQUARE-COATED = x1
CASTOR-BLACK-40MM-TWIN-M8X25 = x 4
FIXING-ALLENKEY-5 = x1
(FOR BED ASSEMBLEY)
CASTORS
Imperial 8 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
LEG-WF5411-COUNTRY-OAK = X4
MRB-SMALL-SQUARE-COATED = x1
RETAIN BAR
CONTENTS FOR 13INCH BASE:
ALLEN KEY
Imperial 13 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
MRB-SMALL-SQUARE-COATED = x1
CASTOR-BLACK-40MM-TWIN-M8X25 = x 4
FIXING-ALLENKEY-5 = x1
(FOR BED ASSEMBLEY)
Imperial 13 inch 3'0 & 2'6
PACKING BAG
FIXING-SCREW-4.0X40 = x4
For securing kframe in place
FIXING-M8HBBOLTS-75 = x4 FIXING-M8HBWASHER = x8
MRB-SMALL-SQUARE-COATED
= x1
CASTOR-BLACK-40MM-TWIN-M8X25 = x 4
FIXING-ALLENKEY-5 = x1
(FOR BED ASSEMBLEY)
LEAFLET-IMPERIAL = x1
FIXING-WASHER-M8X20
= X 4
WASHERS - M8

• Place the boards “fabric side down”
as shown in the photograph.
• Lift each side and lock each of the
black brackets in place.
• Turn by hand each of the Wooden Legs into
the Black “Patented” Brackets.
• With the help of a second
person, turn the base over
ready to accept the two
slatted “K” frames.
3. Fixing the Side Boards in place
4. Securing the legs
Turn the Base ready to t the
2 x Slatted “K” Frames
Please Note: this step will require two
people and requires lifting.
Layout the Side Boards
as pictured
Turn each of the legs to lock the
Side Boards together
AA
AA
BB
BB
CC
CC
INSTRUCTIONS FOR
SHALLOW (8INCH) BASE:
THESE STEPS ARE SPECIFIC TO THE 6 INCH
BASE BECAUSE IT HAS SLIGHTLY DIFFERENT
WAY OF FIXING TO THE 13 INCH VERSION.

• Place the boards “fabric side down” as shown
in the photograph.
• Remove the “Allen Key” bolts from the
xings on each corner of the boards.
• Slot the “Patented Black Brackets” together.
• Place a washer onto the castor thread, and
place into the bracket as shown in image A
• Turn each of the castors into the
“Patented Black Brackets” by hand.
• Tighten with an 11mm Spanner, this will
strengthen the frame together.
3. Fixing the Side Boards in place
4. Turn the Base onto it’s side ready for the next steps
Please Note: this step will require two
people and requires lifting.
Layout the Side Boards
as pictured
Lock the
Brackets in
Place
AA
AA
BB
CCBB
CC
DD
INSTRUCTIONS FOR
DEEP (13INCH) BASE:
THESE STEPS ARE SPECIFIC TO THE 13 INCH
BASE BECAUSE IT HAS A LATCH BRACKET
AND CASTERS
Washer
Bracket
Castor Thread

• Lift each side and lock each of the
black brackets in place.
• Place the Head end rst as shown.
• Place the Foot end slatted frame
in place and then move onto next
step.
• Carefully lifting “by hand” the two slatted frames with the
outer frame still in place, secure with the four wooden
screws in the positions as shown in this diagram.
• With all the previous steps now completed,
turn the Bed onto it’s side ready to accept
the motor and corded remote.
6. Lower the slatted frames into the base.
7. Fix slatted frames in place
8. Turn the Bed onto it’s side
Easier to lower in
from the side.
Head End
Foot End
BB
BBAA
AA
Please Note that these
are not pre-drilled
Please Note: this step will require two
people and requires lifting.

• Remove the sliding caps off each end of the motor.
• Clip the motor in place as shown in image B.
• Once the motor is in place as shown in image C,
re-t the sliding caps back onto the motor.
• Connect the 9v Battery and slide back into it’s
safety compartment.
• Pulling the second to last slat to one side
on the Foot End, slide the retaining bar
into position as shown in Image C.
• Plug in your new bed to a nearby socket
• Make sure that the cables are clear of
the “K” frames and do not get trapped
when the bed is in use.
• Clip the remote onto the side of your
new bed.
9. Fixing the Motor
10. Fixing the Mattress retainer bar.
11. Connect your New Bed.
AACCBBDD
CCBBAA
Please Note: this step will require
two people to complete.
Guide
for the Spirit Upgrade Features Bed electrics
Connect
your remote to the bed
USB
CONTROL
BOX
MOTOR UNIT
PRESS TOP TWO
BUTTONS ON
REMOTE TO PAIR
CONNECT THE
CONTROLLER
CONNECT THE 9V
BATTERY
This is an important
back up power
source.
UPGRADE SPIRIT BED
CONNECT POWER
TO YOUR BED
This is a male ended
connector and
connects into the
motor directly.
POWER
HE 150
CONTROL BOX
LIGHT
USB UNIT
USB UNIT
HEAD END
MASSAGE
UNIT
FOOT END
MASSAGE
UNIT
PRESS BUTTON
TO ACTIVATE
PLUG INTO
SOCKET AND
POWER ON
12. Attach the motor to the bed.
Identify the head and foot sides of
the motor by the images on each end
of the motor.
• Ensure your motor is the correct
way up, please use the highlighted
icons as your guide.
• Slide the caps off each side
of the motor.
• Place the motor on to the cross
bars until you hear it “click” into
position.
• Slide the caps back on to the
motor.
• Connect the Battery
(this is a safety back-up)
HEAD FOOT
Slide off covers Click onto bar Connect battery
Plug controler to
socket on motor
MOTOR-OKIN-88802 ON SURFACE
MOTOR-OKIN-92391 ON SPIRIT
Connect USB power
unit plug
12. Attach the motor to the bed.
Identify the head and foot sides of
the motor by the images on each end
of the motor.
• Ensure your motor is the correct
way up, please use the highlighted
icons as your guide.
• Slide the caps off each side
of the motor.
• Place the motor on to the cross
bars until you hear it “click” into
position.
• Slide the caps back on to the
motor.
• Connect the Battery
(this is a safety back-up)
HEAD FOOT
Slide off covers Click onto bar Connect battery
Plug controler to
socket on motor
MOTOR-OKIN-88802 ON SURFACE
MOTOR-OKIN-92391 ON SPIRIT
Connect USB power
unit plug

Map
of the Spirit Bed Remote
Memory position one Memory position two
HEAD & FOOT UP button:
Press and hold the button, the Head
actuator will simultaneously go up.
Stop when released.
HEAD & FOOT DOWN button:
Press and hold the button, the Head
actuator will simultaneously go up.
Stop when released.
FOOT UP button:
Press and hold the button,
the Foot actuator will go up.
Stop when released.
FOOT DOWN button:
Press and hold the button,
the Foot actuator will go up.
Stop when released.
HEAD UP button:
Press and hold the button,
the Head actuator will go up.
Stop when released.
HEAD DOWN button:
Press and hold the button,
the Head actuator will go up.
Stop when released.
To Store
Memory Setting Under Bed Light
Torch
REMOTE INSTRUCTIONS
M1 M2
Map
of the Spirit Bed Remote
Memory position one Memory position two
HEAD & FOOT UP button:
Press and hold the button, the Head
actuator will simultaneously go up.
Stop when released.
HEAD & FOOT DOWN button:
Press and hold the button, the Head
actuator will simultaneously go up.
Stop when released.
FOOT UP button:
Press and hold the button,
the Foot actuator will go up.
Stop when released.
FOOT DOWN button:
Press and hold the button,
the Foot actuator will go up.
Stop when released.
HEAD UP button:
Press and hold the button,
the Head actuator will go up.
Stop when released.
HEAD DOWN button:
Press and hold the button,
the Head actuator will go up.
Stop when released.
To Store
Memory Setting Under Bed Light
Torch
REMOTE INSTRUCTIONS
M1 M2
MAP
of the Imperial Corded Handset

• The product has only being used for domestic use
• The original proof of purchase can be provided
• The product has remained with the original owner and has not
been resold or gifted
• The product has been used in accordance with the care and
safety guidelines outlined in this document
• The product has not been modified or attempted to be repaired
by any person not authorised by Furmanac
• For the complete terms and conditions please visit
www.furmanac.com
Making a Claim
• The Contract of Sale exists between you and the retailer. Consequently, if you have any concerns, please
contact your retailer in the first instance, giving proof of purchase and outlining the nature of your query.
If the warranty conditions have been satisfied, the retailer will then liaise with Furmanac on your behalf.
Any replacement, repair or refund during this period can only be obtained from your retailer under their terms
and conditions of sale.
• For electrical manufacturing faults within 5years, Furmanac will provide replacement parts to the retailer in to
be able to repair the bed. For other manufacturing faults within 5years, we will discuss with the retailer
whether a repair by a Furmanac technician or replacement will be offered. Whether your Furmanac bed is
repaired or replaced will be at our sole discretion.
• If you find that the retailer you purchased your bed from is no longer in business then please call
01384 408844. Please have details regarding date of purchase, product name and size along with details
of the retailer prior to contacting us. Our dedicated service team will then be able to advise you accordingly.
Your Furmanac Guarantee
We are delighted that you have bought one of Furmanac’s British, quality hand made beds. Don’t forget,
to obtain the full, 5year guarantee you must register your product online. To do this, please visit www.
furmanac.com/registermyguarantee and complete the online form within 30 days of delivery to your
address.
Your upholstered bed frame is provided with a standard 1 Year Guarantee, protecting you against
manufacturing defects. When you register for your guarantee online this will be extended to our 7 Year
Guarantee. If you feel that your product has developed a fault within your guarantee period then please
follow the process below. However, prior to starting this procedure Furmanac strongly recommends
reviewing all the information on the following pages to confirm that the issue is in fact a manufacturing
fault.
Guarantee T&Cs
Please note:
This guarantee is a back to base guarantee and we are not obliged
to repair or replace our product in the end user’s premises.
This guarantee is valid from date of delivery to our customer’s
address and we reserve right at our discretion to repair or replace
any parts that are faulty subject to the following conditions;

Upholstery Care Guide
This guarantee does not cover the general wear and tear of fabrics. Any claims for upholstery faults outside the
realms of general wear and tear. Please ensure the following guidelines have been adhered to as failure to do so will
invalidate your guarantee.
Major cleaning of fabric must be conducted by an upholstery specialist
A multitude of fabrics consisting of different materials, fibres and constructions make up the Furmanac swatches.
As a result of this it is difficult to provide generalised cleaning instructions, therefore it is recommended that any
major cleaning is conducted by an upholstery specialist.
Minor stains
Some stains can be removed by means of a damp (not over wet) cloth and soapy water or mild detergent if
necessary. It is recommended that any chemicals are pretested in an inconspicuous area of the product. After
cleaning the test area please check the compatibility of the fabrics used, specifically monitoring if any colours have
faded or any shrinkage has occurred. If a ring remains around the stain after cleaning, you’ll need to deep clean the
entire product. For more stubborn stains, please consult a professional cleaning company.
Third Party Treatments
Furmanac will not accept liability for upholstery problems caused by any third parties when applying fabric
protection.
Fabric Fading
To reduce fabric fading avoid letting direct sunlight on product by using blinds or curtains.
Spillages
In the event of a spillage the surface must first be blotted dry with an absorbent colour fast cloth or plain kitchen
roll. Avoid using coloured towels or printed paper towels as they may transfer dye or ink to the upholstery.
• DO NOT apply excessive pressure / rub the spillage as this could permanently damage the fabric.
• If a large amount is spilled, remove as much as possible with clean towelling, a scraper or spoon; blot up the
rest, then treat any remaining stains in the same manner as a minor clean.
• Please note fabrics with a high cotton content are at risk of becoming lighter after spot cleaning.
Pile Crush
All pile fabrics, including Chenilles, are subject to a certain degree of shading or ‘pile crush’. This is not a fabric
fault, but the effect of ‘pile crush’ can be minimised (not eliminated) by using a soft brush to lightly brush the pile in
a different direction over areas that show signs of wear.