BARKER AND STONEHOUSE BSH-CD-6002B User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT NOTICE
THIS BOOKLET CONTAINS USEFUL INFORMATION
ABOUT WARRANTY & CARE INSTRUCTIONS.
PLEASE KEEP FOR FUTURE REFERENCE.
AMBLE RISING TABLE
SKU: 5AMBCORNBRWN / 5AMBCORNGREY
BSH-CD-6002B / BSH-CD-6002G

ASSEMBLY INSTRUCTIONS
2
PARTS LIST
Part Qty Part Name
A 1 Upper Table Base
B 1 Table Top
C 1 Lower Table Base
D 1 Glass
E 4 M6 x 40mm Screw
F 4 Washer
G 1 Allen Key
Ax1 Bx1
Cx1 Dx1
Ex4 Gx1 Fx4

3
ASSEMBLY INSTRUCTIONS
SAFETY ADVICE - READ BEFORE YOU START:
• Never use power drills when assembling the table.
• Ensure that you read this manual before starting to assemble your table.
• Check that you have all parts from the parts list. Do not throw away any packaging
until you are confident that you have all parts.
• Assemble this product on a soft/flat surface.
• Place the table glass safely to one side until it is required and never lay the glass
on hard or rough surfaces during assembly.
• It is recommended that two people lift the glass. Ensure you lift with the correct
posture & technique.
• Keep any plastic bags, tools, and fittings away from children and pets.
• After prolonged use we recommend you check all the fittings are tightened
securely.
• Please do not modify this product, use other tools, or substitute parts to build your
item(s), as this will void your warranty.
• Please only use this product for its intended purpose as outdoor furniture within a
residential environment. Failure to do so will void your warranty.
• Barker And Stonehouse holds no responsibility for any damages caused due to
normal wear and tear, incorrect assembly, misuse and/or negligence.
• We reserve the right to make changes for product improvements.
• Please recycle packaging where possible.

ASSEMBLY INSTRUCTIONS
ASSEMBLY
4 5
STEP 1
Loosely secure the upper table base to the table top using M6 x 40mm screws,
washers and the allen key. Once secure tighten all the bolts.
A
E F G
B
G
E
F
x1
A B
x1 x1
E F G
x4 x4
TOP TIP!
Utilise the outer cardboard
packaging where possible. This
will protect your table when
assembling and prevent damage.

ASSEMBLY INSTRUCTIONS
5
ASSEMBLY
STEP 2
Secure the table top to the lower table base by positioning the legs onto
the lower clips located on the inside of the frame and applying pressure
downwards. (Two people required).
C
C
A B
A B
A B

ASSEMBLY INSTRUCTIONS
ASSEMBLY
6
STEP 3
Secure the glass onto the table top ensuring the suction cups are flat.
D
A B
A B D
x1 x1
COMPLETE!
Assembly of the table is now
complete!

ASSEMBLY INSTRUCTIONS
ADJUSTING THE RISING TABLE
7
STEP 1
To adjust the table from the coffee table position, place your foot in the holes
located either side the of table base (two people required).
C
A B

ASSEMBLY INSTRUCTIONS
8
OPERATING THE RISING TABLE
STEP 2
Release the table top from the clips by lifting up the table top, while pushing
the base down with your feet.
C
A B

ASSEMBLY INSTRUCTIONS
9
OPERATING THE RISING TABLE
C
C
A B
A B
TOP TIP!
Dont forget to remove the
protective film from the feet!
STEP 3
Move the table top 3 - 4cm to align it with the higher clips. Once aligned,gently
lower the table top and press downwards to lock into place.

ASSEMBLY INSTRUCTIONS
10
CARE & MAINTENANCE ADVICE
Please read the below Care & Maintenance tips to help
protect your garden table:
• To prolong the life of the tabletop we recommend you always use place mats and
coasters when putting glasses and plates onto the glass.
• Keep your table away from external extreme heat sources.
• We recommend you always use heat mats when placing hot objects on the
tabletop.
• Be careful not to drop any objects onto the table as this could damage the tabletop.
• We always recommend two people to lift the glass.
• Never drag the table as this will accelerate wear and tear on the feet, which is not
covered under warranty.
• We recommend cleaning the table with warm, soapy water. You can use a cloth or
a soft-bristle brush with gentle pressure. Never use abrasive cloths or detergents to
clean the glass. Once you have finished, wash off any residue with clean water.
• For optimum glass and rattan protection we recommend a protective cover is used
all year round.
• We recommend clearing any spills quickly when exposed to direct sunlight. Any
clear liquid on the glass will work as a magnifier, the temperature of the sun’s
rays will increase creating an extremely hot heat source which could damage the
rattan. The same applies to leaving a filled drinks glass on the glass tabletop for an
extended period.

ASSEMBLY INSTRUCTIONS
11