BARTON TOOLS LZ-240C User manual

Company information
◎ Do not use strong chemical cleaning agents or strong detergents to
clean the tools.
◎ In order to ensure the service life of the tool, it is recommended to
replace the hydraulic oil in the tool once a year.
◎ Your tool is a product with excellent design and craftsmanship. You must
not disassemble the internal parts at will.-All damage caused by the user's
unauthorized disassembly or improper use is not covered by the warranty
service, but it can be paid for the user Repair (only charge the cost of parts).
◎ Do not store tools in cold or hot places. Too cold or too hot will deform
the plastic parts of the tool, shorten the life of electronic components, and
damage the battery.
◎ When the tool is left unused for a long time, please reset the piston to
the bottom, wipe the surface of the tool clean, and evenly apply anti-rust
grease on the metal surface of the crimping mold and tool, and put it in the
tool box for storage.
◎ Keep tools and spare parts dry. Rain, humidity, and various liquids or
moisture may corrode tool housings, metal surfaces and electronic
circuits.If the tool gets wet, please remove the battery and wait until the tool
is completely dry before reinstalling the battery.
Instruction Manual of LZ-240C/300C/400C
Plug in Hydraulic Pliers
Repair and Maintenance
LZ Plug in Hydraulic Pliers
◎ Please keep this manual properly. When the user of the product changes,
please give this manual to the new user.
◎ For your safety, please read and understand this manual carefully before use,
and use this product after fully understanding
www.barton-tools.com www.barton-tools.com

Caveat：
3. Remove any grease and dust, especially on the handle and control
components, so as to prevent extremely slipping during use.
4. The built-in safety valve undergoes strict pressure testing before leaving
the factory, and users must not adjust it without authorization! If you
encounter insufficient pressure, please hand the tool to professional
maintenance personnel to handle it and pass the pressure test before using
it.
5. When there is no mold in the working jaw, please do not perform crimping
operation, otherwise it will damage the tool and may cause personal injury!
1. No part of the tool should be hammered or knocked. Before operation,
check whether the tool is damaged, aging, missing parts, inaccurate
adjustment or component jamming, and any other unfavorable factors that
endanger safety and normal operation. Ensure that the switch It can be
operated effectively without any jamming phenomenon. If you find any
problems, please stop using it immediately until the problem is solved.
2. The limit blocks and screws on the clamp head are to prevent the clamp
head from falling off or popping out. Do not remove it by yourself!
Warning: During the process of extending the tool piston, do not put your
fingers or any part of the human body into the working jaws to avoid being pinched!
Company information
◎ Thank you for purchasing and using our company's LZ handheld plug-in hydraulic
tongs. This series fully considers the user's cost-effectiveness. It adopts direct plug-in
220V input voltage and 1100W rated power, which saves battery costs for customers.
The power is strong, reliable and stable, and high quality and low price. The perfect
experience.
Technical Parameters
DIES
LZ-240C LZ-300C
LZ-400C
MODEL
VOLTAGE
FREQUENCY
RATE
LOAD RATE
WORKING RANGE
WEIGHT
AMBIENT
TEMPERATURE
LZ-240C
220V
50Hz
1100W
2200W
2
16-240mm
6.8Kg
12.5Kg
LZ-300C
220V
50Hz
1100W
2200W
2
16-300mm
6.5Kg
12Kg
LZ-400C
220V
50Hz
1100W
2200W
2
16-400mm
8.5Kg
16Kg
-10~40℃
DIES
2
2
16、25、35、50、70、95、120、150、185、240、300mm
【L Z- 30 0C 】：
2
16、25、35、50、70、95、120、150、185、240、300mm
【LZ-400C】：
【LZ-240C】：
GROSS WEIGHT
Instruction Manual of LZ-240C/300C/400C Plug in Hydraulic Pliers
Specification of standard crimping die (hexagonal)
matched with this tool :
1 6, 25, 35, 50, 70, 95, 120, 150, 185, 240, 300
50, 70, 95, 120, 150, 185, 240, 300, 400
The corresponding mold specifications are printed on the side
of the arc.If there are different wire and terminal specifications
to be crimped, please contact the relevant distributor or
manufacturer. The manufacturer can customize crimping
molds of different sizes and special shapes for users.
Note: Please select the crimping mold reasonably according to the wire
specifications and the corresponding copper/aluminum terminals. Improper selection
of crimping dies will cause the wire to be crimped to the copper/aluminum terminal
improperly or produce a lot of flash.
16、25、35、50、70、95、120、150、185、240、300、400mm
www.barton-tools.com www.barton-tools.com