Basic Equipment Floor Dragon User manual

1
Operators Manual
& Parts Schematic
1001 Brown Avenue Toledo, Ohio 43607
TM

2
General Instructions for the Floor Dragon
Operating Instructions
Check machine for damage to cord or plug.
Use suitable pads or brushes.
To install or change the pad:
1. Unplug the machine.
2. Tip the machine back on the wheels.
3. Install brush or pad driver.
4. Center the pad on the pad driver.
To operate the machine:
1. Plug into a grounded outlet.
2. Release the handle and lower it.
3. The handle can be locked into a comfortable
position for the operator.
4. Press the safety lever and squeeze the trigger to
start the machine.
5. Do not operate in one place as damage to the
floor or finish could result.
6. Do not operate the machine with the handle in
the upright position.
7. Remove the pad after every use.
8. Store the machine with the pad
or brush removed.
9. Use only new or clean pads and
reverse them as needed.
Maintenance
To maintain appearance - wipe the machine with a damp cloth
after use.
Warning - Unplug the machine before servicing
Do not operate the machine with a defective or worn cord.
Once per month check the following:
1. Check the cord and electrical system.
2. Check the safety lockout on the trigger.
3. Check wheels.
Safety
Read and understand the manual before operating
this machine.
• Do not operate in explosive areas or use near
flammable liquids, gasses, or dust.
• Attach only to properly grounded outlet.
• Do not expose to rain, store indoors.
• Do not operate the machine with a damaged
cord or plug.
• Do not block or disconnect the safety lever.
• Do not leave the machine plugged in
while unattended.
• Unplug the machine before servicing.
• Do not put fingers under the pad or pad holder.
• Unplug the machine before installing or
removing the pad.
• Use only with suitable pads or brushes.
Warranty
10 Year Coverage
Subject to the conditions stated below, Basic warrants
the plastic parts to be free from defects in materials and
workmanshp for a period of 10 years
to the original purchaser.
3 Year Coverage
Subject to the conditions stated below, Basic offers a
threee year warranty to the original purchaser on other
components to be free from defects in
materials and workmanship.
Exempt Wear Items:
The following items are not included in the coverage
above: Power cords, transport wheels, pad drivers,
clutch plates, and handle grips. This warranty is void if
products are used for any purpose other than that which
was intended. There are no other warranties
expressed or implied.
Specifications
Length - 22 in.
Width - 17.5 in.
Height - 49 in.
Weight - 95 Lbs. (with cord)
Pad Speed - 175 RPM
Pad Diameter - 16 in.
Drive motor - 1.5 HP, 120v, 12 A, 60 HZ
Cord - 14-3 ST, 50 ft.

3
ref# part# description
1E83191
Motor, 1.5hp, 115v, 60hz,
w/3 planet gear box.
2E81140 Cover, motor 9’O.D.x 1.65’ Blk
3E81526 Screw, 10-32 x 1/2
4E81176 Plate, Weldment 17” Stl Floor Machine
5E83563 Ring
6E81230 Base, Steel 17” with bumper & handle
7E81294 Hose Barb 1 1/2”
8E81363 Hose 33” x 1 1/2” w/ cuffs
9E81362 Hose Bracket w/coupling 1 1/2”
10 E81518 Nut, conduit 1 1/2”
11 E81582 Plug, 3/8 Blk
12 E81381 Dust Band 4” wide
13 E81148 Pad Driver, 16” Tri-lock
14 E81089 Bolt, 5/16-18 x 3/4
15 E81067 Washer, lock 5/16
16 E81062 Washer, Flat USS 5/16”
17 E83143 Cap, axle 1/2’
18 E81124 Wheel, 5” Flat
19 E83145 Washer, nylon 1/2”
22 E81092 Bolt, shoulder 1/2 x 1/2
23 E81076 Nut, 3/8 Nylock
FLOOR DRAGON PARTS

4
Basic Equipment
1001 Brown Avenue
Toledo, Ohio 43607
800.441.1934
FLOOR DRAGON PARTS
ref# part# description
1E83523 Nylon Cable Tie
2E83132 Cord, Handle, 14-3
3E83789 Nut, Electrical Conduit, 1/2”
4E83790 Cord, 50 Feet, 14-3ST
5E83496 Strain Relief for Replacement
6E81064 Bolt, Hex. 1/4-20 x 3/4
7E83520 Nut, Nylock, 1/4-20
8E83127 Grip
9E83651 Screw, Phillips, No. 6x1
10 E83426 Screw, Phillips, 1/4-20 x 1.75”
11 E83130 Spring
12 E83270 Clip, Spring
13 E85032 Switch
14 E83129 Safety Lock
15 E82752 Trigger, Switch
16 E83325 Cover, Switch Box
17 E82750 Switch Box, Handle, Dual Speed
18 E81105 Plate, Switch
19 E83451 Handle Tube, 7/8 x 16
20 E81065 Bolt, Hex. 1/4-20 x 1.75” Grade 5
21 E81070 Nut, Nylock, 1/4-20
22 E83519 Grommet, .375” ID
23 E83137 Cord Hook
24 E83135 Oval Washer
25 E81133 Handle, Cam Lock Assembly
26 E81379 Washer, Spring, 3/8
27 E81063 Nut, Nylock, 5/16-18
28 E83145 Washer, Nylon
29 E81077 Bolt, Shoulder, 3/8 x 1
30 E83269 Washer, Spring, 1/2
31 E83143 Caps, Axle, 0.5
32 E83717 Handle attachment, Welded ‘T’
33 E83136 Bracket, Flat Handle
34 E83711 Handle Tube
35 E81394 Axle, 1/2 x 6.625”
B9164-9212 Sept14I