Bastow OXFORD AND NELSON GEORGIAN G5343E User manual

with Cross Handles
G5343E
Basin Set - English Outlet
165mm
100mm
120mm
51mm 51mm
100mm
165mm
100mm
120mm
51mm 51mm
110mm
with Lever/Porcelain Handles
G5343ELV / G5343EPLV
Basin Set - English Outlet
GEORGIAN
basin set english
G5343E
Specifications
Features
Recommended Use Domestic, Commercial, Hotel
Material Brass Body
Finishes Satin Chrome, Nickel, Brushed Nickel, Gold, Brass Gold N18, Brushed
Gold N18, Rose Gold, Brushed Rose Gold, Matt Black, Black Sapphire
Brushed Black Sapphire, Gunmetal, Satin Pearl, Copper, Antique Copper
Dimensions
Standards
Handle
Tap Outlet
WELS Rating
120W x 100D x 165H mm x 51Ø mm Flange
AS/NZS 3718
Cross Handle, Lever Handle, Porcelain Lever Handle
Fixed, Swivel and English
Flow Rate: 6L/min, Stars: 5 AS/NZS3718 Lic WMKA 26319
WaterMark
TM
Products in this specification manual must by regulation be installed by licensed and registered trade people.
Under our commitment to product development and improvement, we may change product specifications
and dimensions or delete models from the range without prior notification. Dimensions and set-outs listed
are correct at time of publication and could contain dimensions which are approximate due to tolerances in
manufacturing processes. It is important that you thoroughly review the product and check specifications
and dimensions prior to surface preparation, cut-out and installation.
During the installation of the product by a qualified trained personnel, make sure that the entire fastening
surface is even and smooth (no protruding seams or tile oset), that the finish of the wall is suitable to apply
the product and has no weak points. It is recommended that all accessories are secured to timber studs.
Disclaimer:

Specifications
Pressure Rating As per AS/NZS3500 pressure must be limited to 500kPa on any new
home, extension or renovation.
For best performance and longer life we recommend 150-500kPa.
Hot and cold water inlet pressure should be equal.
Temperature Rating 80°C maximum continuous working temperature
Suitable Hot Water Units Storage Tank - Yes
Continuous Flow - Yes
Gravity Feed - Not suitable
Cleaning Instructions
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty - refer to our
Warranty Conditions.
Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference
For the Plumber
Check 1. All work should be carried out by a licensed plumber. Responsibility will not be accepted by
Tribata for incorrect installation of this tapware, or any tapware not installed by a Registered Plumber.
Check 2. The water supply lines need to be ‘flushed out’ prior to installation. This will avoid any foreign
materials blocking the flow regulator, damaging the cartridge/valve and reducing the flow of water.
Check 3. Ensure all connections are tight.
Check 4. Turn on the main water supply and check for leaks.
GEORGIAN
basin set english
G5343E
Specifications
Products in this specification manual must by regulation be installed by licensed and registered trade people.
Under our commitment to product development and improvement, we may change product specifications
and dimensions or delete models from the range without prior notification. Dimensions and set-outs listed
are correct at time of publication and could contain dimensions which are approximate due to tolerances in
manufacturing processes. It is important that you thoroughly review the product and check specifications
and dimensions prior to surface preparation, cut-out and installation.
During the installation of the product by a qualified trained personnel, make sure that the entire fastening
surface is even and smooth (no protruding seams or tile oset), that the finish of the wall is suitable to apply
the product and has no weak points. It is recommended that all accessories are secured to timber studs.
Disclaimer:

Installation Instructions
IMPORTANT INFORMATION, please read before starting installation.
CHECK 1
For packaging purposes, this tapware may come partially assembled.
CHECK 2
Before installation, please ensure that you have checked the assembly of all components and joints.
CHECK 3
Always use plumbers tape or a recommended sealing compound on all threaded joints.
CHECK 4
Please pressure test the tapware prior to installation using recommended testing equipment.
CHECK 5
The installer is responsible for selecting the correct fittings and that the distances are correct
before installation.
Plumber Instructions
Note: Installation should only be carried out by a licensed plumber. Tribata do not accept any
responsibility of incorrect installation if not installed by a registered plumber.
Note: Foreign materials can block the flow regulator, damage the valve and reduce water flow.
Please flush the supply lines prior to installation.
Note: Mixers require flexible hoses which are included and marked in red (hot) and blue (cold).
INSTALLATION
1. Take the rubber seal and place it on the underside of the base ring. Screw the flexible hoses
into the mixer and tighten, and remove any kinks in the hoses.
2. Screw the mounting stud to the underside of the mixer, and then tighten with a screwdriver.
3. Seat the mixer in the allocated hole, with the hoses going through first.
4. Underneath the bench top you can now fit the base washer, base plate and fixing nut.
5. Clamp the mixer firmly to the vanity by tightening the fixing nut.
6. Flush the lines to clear the debris
7. Now connect the water supply to the isolating stop valve.
REPLACING THE MIXER CARTRIDGE
1. Remove the grub screw inside the lever handle and lift o the handle
2. Unscrew the dome cap and the nut lock.
3. Remove the old cartridge and clean the casing
4. Insert the new cartridge ensuring the lungs line up with the holes in the main body.
5. Assemble the fixing nut, the dome cap and finally the handle.
GEORGIAN
basin set english
G5343E
Specifications
Products in this specification manual must by regulation be installed by licensed and registered trade people.
Under our commitment to product development and improvement, we may change product specifications
and dimensions or delete models from the range without prior notification. Dimensions and set-outs listed
are correct at time of publication and could contain dimensions which are approximate due to tolerances in
manufacturing processes. It is important that you thoroughly review the product and check specifications
and dimensions prior to surface preparation, cut-out and installation.
During the installation of the product by a qualified trained personnel, make sure that the entire fastening
surface is even and smooth (no protruding seams or tile oset), that the finish of the wall is suitable to apply
the product and has no weak points. It is recommended that all accessories are secured to timber studs.
Disclaimer: