BAT BATmode S User manual

1
QUICKSTART GUIDE
BATmode S / S+
Set Up and First Start Up

2
SAFETY INSTRUCTIONS
Please read these safety instrucons carefully before startup your
BATmode system! !
Only use power supplies authorized by bat bioacousctechnology.
Avoid excessive mechanic strain on the BATmode-System, especially on
plugs and connectors if cables are connected to the BATmode or the antenna
and microphone disc. Strong vibraons, shaking or dropping may damage system parts.
Ensure a safe and stable mounng of the BATmode and the corresponding discs.
Dropping can harm persons, property or the BATmode-system.
Ensure that nobody can stumble on installed and connected wires.
Stumbling can harm persons and damage system parts.
Only use accessories supplied or authorized by bat bioacousctechnology.
The use of unauthorized accessories may damage the device.
Please contact our support if the BATmode-System shows any damage or does not work
properly. Do not open system parts and try to repair damage by yourself or through unauthorized
personnel. This will cause the loss of warranty.

3
Table of Contents
SAFETY INSTRUCTIONS ................................................................
Learn about your device ...................................................................
LED Status Indicators .......................................................................
Antenna Disc and UltraSoundGate ...................................................
Microphones .....................................................................................
Connect ...........................................................................................
Remote Access via WIFI .................................................................
Remote Access via LAN ..................................................................
First Start Up ...................................................................................
Mobile Set Up ..................................................................................
Daily Status SMS..............................................................................
Remote SMS ...................................................................................
Set Up .............................................................................................
Installation .......................................................................................
2
4
5
6
7
10
12
13
14
16
17
18
22
myBAT ............................................................................................ 20
21

4
Learn about your device
- Front View BATmode S/S+ -
mode
BAT S+
- Back View BATmode S/S+ -
WWAN
19V
-+
WIFI
On-/Off-Switch
Mobile Service LED
WIFI-Hotspot LED (only BATmode S+)
Power LED
Status LED
SIM-Card Slot (Mini-SIM)
USB-Port for UltraSoundGate (monitored)
USB 2.0-Port e.g. for keyboard and mouse
Temperature Sensor Input (only BATmode S+)
Precipitaon Sensor Input (only BATmode S+)
Cellular Antenna Connector
Heang Output
Power Supply
Minidisplay Port
LAN Connector
USB 3.0-Ports e.g. for Backup-Sck
Kensington-Lock
WIFI Antenna Connector (only BATmode S+)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2 3 4 5 6 7 8 9 10
1
18
12 13 14 15 16 17
11

5
How to interpret the LED status indicators of your BATmode correctly:
LED Status Indicators
Power LED (orange)
On
Off
Device on
Device off
WIFI Hotspot LED (green)
On
Off
WIFI-Hotspot on
WIFI-Hotspot off
Status LED (blue)
On
Off BATcontrol not started
Monitoring stopped,
BATcontrol on
Mobile Service LED (green)
On
Single blinking
Mobile connecon connected
Registered to mobile network
Blinking Monitoring started
Double blinking SIM locked, SIM not recognized,
no mobile service connecon

6
- Antenna Disc (only BATmode S+) -
- UltraSoundGate 116Hnbm -
WIFI Antenna Connector
Temperature Sensor Connector
Cellular Antenna Connector
BATmode S Systems do not use an Antenna
Disc. Instead, please connect the enclosed magnec
base antenna for mobile connecon to the cellular
antenna connector of the BATmode S.
Microphone XLR Connector
USB-2.0 Interface
Antenna Disc and UltraSoundGate
1
2
3
4
5
3
1
2
45

7
Microphones
- Front View -
Reference Signal Speaker Connector (UltraSoundGate)
Microphone XLR Connector (UltraSoundGate)
Screws for removing the mounng plate
Reference Signal Speaker
Microphone Capsule
The Microphone Disc GM50 can either be used with
the enclosed mounng plate or with an oponal
tripod.
Microphone Disc GM50
Be careful not to touch the microphone capsule and to
protect it from moisture!
- Back View -
To connect the microphone and the reference signal
of the GM50 speaker please use the Y-XLR
microphone cable.
1
2
3
4
5
5
4
GM50
3
1
2

8
- Front View -
Microphone XLR Connector (UltraSoundGate)
Heang Connector
Windscreen made of foam
Reference Signal Speaker
Microphone Capsule
Do not remove the windscreen foam,
as this has an essenal influence on the
calibraon of your microphone disc!
Microphone Disc GM90
Be careful not to touch the microphone capsule and to
protect it from moisture!
- Back View -
Microphones
2
1
5
4
3
1
2
3
4
5

9
Tower Microphone TM10
Microphone XLR Connector (UltraSoundGate)
Microphone Capsule
Oponally available movable tripod for
tower wall mounng
Be careful not to touch the microphone capsule and to
protect it from moisture!
Tower Microphone TM20
Microphone XLR Connector (UltraSoundGate)
Microphone Capsule and Reference Signal
Speaker
Oponally available movable tripod for
tower wall mounng
1
2
3
4
5
6
1 2 3
4 5 6

10
Connect
- BATmode S+ -
How to connect all components of your BATmode S+ System correctly:
- Antenna Disc -
- Microphone -
- UltraSoundGate 116Hnbm -
- Monitor -
- Keyboard / Mouse -
- Precipitaon Sensor -
- Backup-Sck -
Please follow the manual
of the precipitaon sensor
Depending on the selected microphone,
the heang can be omied
Oponal and not included in delivery scope
mode
BAT S+
WWAN
19V
-+
WIFI - Power Adapter -

11
- BATmode S -
How to connect all components of your BATmode S System correctly:
- Magnec Base Antenna -
- Microphone -
- UltraSoundGate 116Hnbm -
- Monitor -
- Keyboard / Mouse -
- Backup-Sck -
Depending on the selected microphone,
the heang can be omied
Oponal and not included in delivery scope
- Power Adapter -
mode
BAT S+
s
WWAN
19V
-+

12
Remote Access via WIFI
How to access your BATmode with your Windows running laptop via WIFI:
Step 2
Open the Windows program
,Remote Desktop Connecon
insert the WIFI IP of your BATmode
in Computer and press . Connect
Step 3
Insert the Username „BAT“ and the
Windows Password and press . OK
Step 1
Connect the WIFI of your Windows running laptop
with the WIFI-Hotspot of the BATmode.
Default SSID: „BATmode“
Default Password: „12345678"
Default WIFI IP: „192.168.137.1“
Default Windows Password: „12345“
WIFI connecon is only available for BATmode S+.

13
Remote Access via LAN
How to access your BATmode with your Windows running laptop via LAN:
Step 2
Open the Windows program
,Remote Desktop Connecon
insert „batmode“ in Computer
and press . Connect
Step 3
Insert the Username „BAT“ and the
Windows Password and press . OK
Step 1
Use an Ethernet cable to connect the LAN port
of your Windows running laptop (RJ45)
with the one of the BATmode (RJ45).
Default Windows Password: „12345“
WWAN
19V
-+
WIFI

14
First Start Up
Starng of the BATmode System and the BATcontrol control soware:
Step 1
Start the BATmode System.
Step 2
Use mouse, keyboard and monitor or
connect your laptop via WIFI or LAN as
described on page 12 and 13.
The control soware BATcontrol starts
automacally.
1
Status Bar
Task Bar for page choosing
Message Bar
Selected Page
Monitoring Start-/Stop-Buon
1
2
3
4
5
1
2
3
4
5

15
Step 3
To stop data acquision click on the Start-/
Stop-Buon or close the recording soware.
The recording soware will open and the
acousc monitoring as well as the
simultaneous data acquison of
temperature and precipitaon begin.
Starng of the Aviso-RECORDER USGH recording soware and the start of the acousc
monitoring and data acquision of the external sensors:
The external sensors for temperature and precipitaon acquision are only available for BATmode S+.
Step 1
Aer selecng your sengs on the different
pages of BATcontrol, start the monitoring
with a click on the Start-/Stop-Buon.
Step 2
The recording soware Aviso-RECORDER USGH offers
lots of sengs. However, the BATmode system is
configured especially for the bat detecon on wind
turbines according to the requirements specified in the
research project RENEBAT. Consequently, sengs in
the recording soware should only be changed by
experts following the instrucons in the detailed
manual. Otherwise validity of collected data may expire.

16
Step 2
Mobile Set Up
Use the Mobile sengs in Windows to remove
a possibly acvated PIN from your SIM card.
Step 3
Enter the number of the SMS center of your
provider in in BATcontrol. SMSC-Number
How to set up your BATmode for SMS and mobile Internet connecon:
Step 4
Insert the APN of your provider in the mobile
sengs of Windows.
Step 1
Insert the Mini-SIM card in the SIM card slot
(For this, the BATmode must be turned off).
An acvated PIN will prevent the BATmode
system to restore a mobile connecon
aer a possible power failures, automacally.

17
Daily Status SMS
Sengs in BATcontrol
Enable and insert the phone numberDaily Status SMS
of the receiver of the Daily Status SMS in .Receiver Number(s)
Use the internaonal format: e.g. [phone].
Use ; to separate mulple receiver numbers.
Select the daily transmission me and the desired
format.
HRI: Values preceded by acronym.
CSV: Values separated by commas.
ID
MON
LRL
LRD
ID of the BATmode Systems
Current monitoring status
Last reference value
Time of the last reference value
Recordings in the last 24 hours
Time of last recording
Meaning of the sent values and acronyms
Acron. Meaning
LFD
FL24
FT
FC
FD
SL
Total number of recordings
Free space on C: in GB
Free Space on D: in GB
Current mobile signal level in %
Status of the WIFI-Hotspot
Status of the Internet connecon
Acron. Meaning
WWW
WIFI

18
Remote SMS
Start monitoring!
Start monitoring: 11:00-14:00!
Start monitoring: 11:00-14:00 and 20:00-02:00!
Start monitoring: -20/10!
Stop monitoring!
Kill Recorder!
Monitoring will start ungated
Monitoring will start from 11 am to 2 pm
Monitoring will start from 11 am to 2 pm and 8 pm to 2 am
Monitoring will start from 20min before sunset to 10min
aer sunrise
Monitoring will stop
Recording soware RECORDER will be killed
Use these SMS commands to control your BATmode systems via text SMS
Command System response
Download from the Google Play Store our free
Android App for SMS remoteBATconnect SMS
control of your BATmode systems.
Sengs in BATcontrol Android-App
Enable the checkbox.SMS Remote
Add the mobile number of the command
sending device to the . Security Number(s)

19
Enable Status-Mail!
Send LAN-IP!
Disable Status-Mail!
Enable Status-SMS!
Disable Status-SMS!
Daily Status Mail will be enabled
System will send its LAN IP
Daily Status Mail will be disabled
Daily Status SMS will be enabled
Daily Status SMS will be disabled
Reset USG!
Send MAC!
Send WIFI-IP!
System will reset UltraSoundGate
System will send its MAC adress
System will send its WIFI IP
Reboot!
Shutdown!
Send Mail to max(at)moritz.de
Send status!
Send Mail!
Start WIFI-Hotspot!
Stop WIFI-Hotspot!
Connect WWAN!
Disconnect WWAN!
System will reboot
System will shut down
Systen will send Status Mail to ma[email protected]
System will send Status SMS
System will send Status Mail
WIFI-Hotspot will start
WIFI-Hotspot will stop
Mobile Connecon will be connected
Mobile Connecon will be disconnected
Kill Recorder! Recording soware RECORDER will be killed

20
myBAT
Use the mybat cloud service to monitor your BATmode systems from anywhere in
the world.
myBAT requires an acve Internet connecon via LAN or mobile connecon.
Step 1
Acvate myBAT in BATcontrol on your BATmode.
Step 2
Sign Up by using your Purchase-Code on:
hps://www.mybat.bioacousctechnology.de
Step 3
Assign your BATmodes to your account by using
the MAC addresses of your BATmode systems.
Purchase-Code:
MAC adress of this BATmode: