BATHSELECT BSTD005-1ORB User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
BATHSELECT 16" DARK OIL RUBBED BRONZE/MATTE
BLACK SQUARE COLOR CHANGING LED RAIN
SHOWER HEAD INSTALLATION INSTRUCTIONS
Product code: BSTD005-1ORB
1
Please read installation instructions below. All plumbing should be
installed in accordance with applicable building codes and regulations.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
All products must be installed by a professional and certified plumber
otherwise warranty may be voided.
PRIOR TO INSTALLATION
Customer Service: 800-500-9895
bathselect.com

Customer Service: 800-500-9895
bathselect.com
2
Ceiling Mount Shower Installations Instructions
Step 1: Step 2:
Step 3: Step 4:
Step 5:

Customer Service: 800-500-9895
bathselect.com
3
Step 1: Take Out the Old Shower Head
You can easily remove it by hand, but depending on how long the rain showerhead has
been installed, you might need to use an adjustable wrench. Hence, if you find it difficult
to remove, rotate the showerhead with an adjustable wrench in a counterclockwise
direction to unscrew it.
Step 2: Keep the Shower Arm Clean and In Good Shape
After you have removed the head, check the shower arm threads for any debris and old
Teflon tape. If you find any, remove it and clean them off thoroughly. It’s best to use a
microfiber cloth when cleaning the thread because it removes Teflon tape perfectly and
works great to pick up tiny grits.
Once you’re done cleaning, check if it is corroded or leaking. For damaged threads, it will
be best you replace it entirely so you can have a comfortable shower experience any time.
Step 3: Time to Add New Teflon Tape
Since you have removed the old Teflon tape, you have to replace it with new ones. The
reason is that this tape helps to protect the shower from leaking after installing the
showerhead. Now apply the new Teflon tape about 3-5 turns on the thread and tear the
end part. Use your hands to smooth it out to keep it leveled to the thread. Keep in mind
that when applying the tape, you should go in a clockwise motion so that it doesn’t come
off when you attach the head in the same direction.
Step 4: Connect the Showerhead
As said earlier in the tools needed, we’re using the rubber sealing washer that comes with
the showerhead. This tool helps to make the showerhead stay watertight and secured on
to the thread. Ensure you place it properly before installing it.
After that, reconnect the shower head and tighten it down with your hands. You can
employ a chair or ladder to make things easier for you.
Step 5: Tighten the Showerhead
On To the Thread You will need to get the adjustable wrench handy to tighten down the
shower very well. But make sure you wrap the threads with a terry cloth, so it doesn’t
damage the finish when tightening the showerhead.
Once you have done that, now use the adjustable wrench to tighten down the
showerhead. However, don’t over-tight or force it so that it’s easier to remove in the future.
The LED light will change its color by detecting water temperature:
0-30°C (32-86°F): Blue LED
30-40°C (86-104°F): Green LED
40-50°C (104-122°F): Red LED
50-100°C (122-212°F): Flashing Red LED
Note: The LED lights are powered by water flow, and will be activated once the water is
turned on.

Customer Service: 800-500-9895
bathselect.com
4
Wall Mount Shower Installations Instructions
Step 1: Step 2:
Step 3: Step 4:
Step 5: Step 6:

Customer Service: 800-500-9895
bathselect.com
5
Step 7:
1. Apply plumber's tape to the threads on both ends of the shower arm and slide on the
decorative escutcheon.
2. Insert the new arm into the fitting in the Wall and twist to tighten. Finish tightening
with your adjustable wrench. Wrap a dry cloth around the shower arm to protect the finish
while tightening with adjustable wrench.
3. Thread the new shower head onto the arm and hand-tighten. Hold the shower arm in
place with groove joint pliers and finish tightening the shower head with your adjustable
wrench. Wrap both in a dry cloth to protect the finish.
4. Before securing the decorative escutcheon, turn on the water supply to make sure that
all connections are tight and there is no leaking. If no leaks are detected, continue with the
installation. If leakage does occur, use your adjustable wrench to tighten the connections
as necessary.
5. Apply a bead if silicone sealant to the back of the escutcheon and press firmly into place
against the installation surface. Wipe away any excess sealant with your damp cloth.
The LED light will change its color by detecting water temperature:
0-30°C (32-86°F): Blue LED
30-40°C (86-104°F): Green LED
40-50°C (104-122°F): Red LED
50-100°C (122-212°F): Flashing Red LED
Note: The LED lights are powered by water flow, and will be activated once the water is
turned on.

Customer Service: 800-500-9895
bathselect.com
6
Acid
Care & Cleaning
General Information
1. The product can be cleaned with warm water, a mild soap and a clean soft cloth.
2. Clean progressively and gently.
3. It is not required to use any abrasive cleaning pads, wire wool or cloths to clean the
product.
4. Avoid a vigorous cleaning action, as this could contribute to denaturing and dulling
5. Abrasive or strong cleaning products containing ammonia, bleaches, alcohol, dyes,
acids (hydrochloric, formic, phosphorus, chlorine or acetic) will be not be affected.
All products manufactured and supplied by BathSelect are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected
6. If using a spray cleaner, apply the cleaning agent onto a soft cloth, never directly
spray onto the product as the cleaner may enter gaps and openings and cause
damage. Do not allow the cleaner to remain on the product for a period of time. After
cleaning, rinse thoroughly with clean water.