Baumatic BRZF1760W User manual

d yo
BRZF1760W
245 litre Freezer

USER MANUAL FOR YOUR BAUMATIC
BRZF1760W
245 litre freezer
2
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference, for
you or any person not familiar with the operation of the appliance.
GS 29/06/12

3
Contents
Environmental note 4
Important safety information 5 – 7
Specifications of your freezer 7 – 8
Specifications 7
Dimensions of the appliance 7
Description of the appliance 8
Using your Baumatic freezer 8 - 10
Before switching on 8 - 9
Duringfirstuse 9
Switching on the appliance and setting the thermostat 9 - 10
Storing food in the **** freezer 10 - 13
Freezing fresh food 11
Tipsonfreezing 11
Storing commercially frozen food 12
Defrostingfrozenfood 12
Normaloperatingnoises 12-13
Saving energy when using your freezer 13 - 14
Cleaning and maintenance 14 - 15
Defrosting the freezer compartment 15
Installation 16 - 19
Electrical connection 16 – 17
Reversing the door swing 17 - 18
Positioning 18-19
Troubleshooting 19 – 22
Baumatic consumables 23
Technicaldata 24
Contactdetails 25

Environmental note
Note : Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
oThe packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
oPlease discard all packaging material with due regard for the
environment.
4

Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Customer
Care Department.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
Use of the appliance
oYour appliance is only designed to be used in the
home. It is suitable for storing food that needs to
be frozen. If it is used for any other purpose or it is
not used correctly, then Baumatic Ltd. will accept
no liability for any damage that is caused.
oAltering the specification of the appliance must not be attempted
for reasons of safety.
Before using your appliance
oCheck the appliance for any signs of transport damage. If you
notice any damage, then you should not connect your appliance
to your mains supply and should contact your retailer.
Refrigerant
oYour appliance contains R600a refrigerant, which is a natural gas
that does not contain CFCs that can damage the environment.
However it is a flammable substance, therefore care should be
taken:
During the transportation and installation of the
appliance, make sure that the refrigeration pipework
does not get damaged.
If it does become damaged then sources of ignition
and open flames should be avoided. Also the room
that the appliance is situated in should be thoroughly
ventilated.
5

oDo not place any objects on top of the appliance, as
this may damage the table top.
Child safety
oPackaging material should be kept away from
children.
6
oChildren should not be allowed to touch the
controls or play with the appliance.
General safety
oDo not pull on the power supply cable to remove the plug from
your mains supply socket.
oDo not pull out or insert the plug with wet hands.
oDo not attempt to use your appliance outdoors or
any place where it is likely to come into contact
with the elements.
oBefore cleaning the appliance or performing
maintenance work, ensure that the appliance has been
disconnected from your mains supply.
oNever allow the back coils of the appliance to come into contact
with the wall surface.
oAlways ensure that the location where you are installing your
appliance is free of stored items such as papers and other
flammable materials.
oNever block the ventilation openings of the appliance, either on
the inside or its exterior.
oIt is vital to keep your appliance well ventilated,
so that there is proper air flow between the
bottom of the unit and the plinth/kick plate
which it is sitting on.
oDo not place electrical devices inside of the appliance, such as
mixers or ice cream makers.

Service
You should not attempt to repair the appliance
yourself, as this could cause injury or a more serious
malfunction. If you require a service call then please
contact the Baumatic Customer Care Department.
Specifications of your freezer
oTotal gross/net capacity: 245 / 225 litres
oEnergy efficiency class: A+ (0.71 kW per 24 hours)
oFreezer star rating: ****
oFreezing capacity (kg / 24 hour): 11 kg
oAdjustable thermostat
oManual defrost
o7 x Transparent freezer drawers
oReversible door
oAdjustable feet
Dimensions of the appliance
Height: 1700 mm
Width: 600 mm
Depth: 600 mm
IMPORTANT: When you install your appliance it is important to bear
in mind its climatic rating.
In order to find out the climatic rating of your appliance, you should
check the rating plate. The rating plate is located on the front edge of
the inside of the freezer, behind the drawers. The rating plate will
indicate the ambient temperature range that your appliance will
function correctly within.
Model number ………………………………………………………………………
Serial number ………………………………………………………………………
Date of purchase ………………………………………………………………………
7

Description of the appliance
8
Using your Baumatic freezer
Before switching on
oMake sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
oAfter delivery, wait for eight hours before connecting the
appliance to your mains supply. This will allow any refrigerant
gasses that may have been disturbed during the transportation
process to settle.
oThe outside of the appliance and the removable accessories
contained within it, should be cleaned with a solution of liquid
detergent and water.
oThe interior of the appliance should be cleaned
with a solution of sodium bicarbonate dissolved in
lukewarm water. The interior and accessories
should be thoroughly dried, after the cleaning
process has been completed.

oThere can be an odour when you first switch on the appliance. It
will lessen as the appliance starts to cool.
During first use
oWhen you first switch on the appliance, the compressor will run
continuously for approximately 24 hours or until the freezer
reaches a cool enough temperature.
oWith dry hands, connect your appliance to your mains supply.
Set the control dial to position MAX for a 24 hour period, before
placing food in the freezer drawers.
oDuring this period of time, you should try not to open the door
frequently or place a large amount of food within the appliance.
oIt is strongly recommended that you use a freezer thermostat to
check that the temperature in the freezer is below -18°C before
loading any food into it.
oIf the unit is switched off or unplugged, you must allow at least 5
minutes before restarting the appliance on the thermostat or
reconnecting it to your mains supply.
Switching on the appliance and setting the thermostat
oYou switch on your appliance by connecting it to your mains
supply and setting the thermostat.
oThe thermostat automatically regulates the temperature inside
the freezer depending on what you have the control panel set to.
oIt is recommended that the control dial is set to position
NORMAL after the 24 hour cooling period. You should use a
suitable thermometer to check the temperature after 2 hours to
ensure the freezer is below -18°C.
9

oThe freezer compartment temperature will vary between -18°C
and -25°C during a typical cycle.
oIMPORTANT: The ambient temperature of the room,
the temperature of food and the amount of food that
has been placed in the freezer and how often the door is
opened, will all affect the temperature being maintained
by the appliance.
oOn the MAX setting your freezer will work harder to maintain a
lower temperature and will increase the energy usage. There is
no need to run your appliance at this setting for prolonged
periods. Unless you are freezing fresh food, you should have the
digital thermostat set to NORMAL.
oIf the unit is switched off or unplugged, you must allow at least 5
minutes before restarting the appliance or reconnecting it to
your mains supply.
Storing food in the **** freezer
The freezer is suitable for storing and freezing food.
oThe freezer temperature must have already reached -18 degrees
centigrade (or lower) before you attempt to store food that is
already frozen or freezing fresh food.
oThe freezer is only able to freeze a certain quantity of food at
one time. You should not attempt to freeze more than 11
kilograms of fresh food within a 24 hour period.
oAny of the drawers can be used for freezing various foods.
oWarm food should be allowed to cool down before you attempt
to freeze it. If you place warm food in the freezer section, then
the increased humidity will cause quicker ice formation and
increase the amount of power that the appliance uses.
oDo not open the freezer door too often or leave the door open
for long periods of time, as this will increase the temperature
inside of the appliance and will increase the energy usage.
oThe guidance of the food manufacturer should be followed, in
regard to the maximum storage time.
oThawed foods must not be frozen for a second time.
10

oIf power is cut to your appliance, DO NOT open the door to the
freezer. Your freezer will store food safely for approximately 9
hours.
oIMPORTANT: If the food has started to defrost before power is
restored, then DO NOT re-freeze the items. The food should be
used within a relatively short period of time.
Freezing fresh food
oFresh food should be packed into airtight containers
or packaging. This will help to make sure that the
food doesn’t dry out or lose its flavour. It will also
ensure that flavour does not transfer from other
foods.
oDo not allow fresh food to touch items
that are already frozen.
oChill fresh food in a fridge before freezing if possible.
Tips on freezing
oFreezer bags, polythene wraps, aluminium foil (extra thick) and
special cans for frozen foods are suitable packaging for storing
frozen goods in.
oTape, rubber bands or plastic clips are
suitable for sealing bags and wrappings.
11
oBefore sealing a suitable bag, you should
compress the air out of it, as this will help
the food to freeze more easily.
oFlat packages freeze more easily.
oIf you are freezing liquid, then do not fill the
container to the brim. Liquids will expand
when being frozen.
oDo not place bottles (glass or tin)
containing liquids (especially sparkling
liquids) into the freezer as they could

12
cause the bottle to burst during freezing.
Storing commercially frozen food
oThe storage time and recommended temperature for storing
commercially frozen foods are indicated on the packaging.
oAlways follow the manufacturer’s instructions for storage and
use of frozen food.
oWhen shopping, be careful to choose food which is adequately
packed and is provided with complete storage instructions. It
should have been stored in a freezer where the temperature
does not rise above -18°C.
oDo not buy packages of food that are covered with frost. This
could indicate that the package has thawed at least once before.
oTake care that your frozen food packages do not start to thaw
before you place them in your freezer. This will shorten the
length of time that you can safely store the food for.
Defrosting frozen food
oPartially thawed or defrosted foods should be used as soon as
possible.
oCold air preserves the food but it does not destroy the micro
organisms which rapidly activate themselves after defrosting and
make foods perishable.
oPartial defrosting reduces the nutritional value of food, especially
fruits, vegetables and readymade meals.
Normal operating noises
Ice cracking noise
oCan be caused by expansion and contraction within the freezer.
Short cracking noise
oCan be heard when the thermostat turns the compressor on and
off.
Compressor noise
oThere will be an operating noise when the compressor is running.

13
oAfter installation, the compressor may be noisier for a short
period of time.
Bubbling and burbling sound
oThis noise is emitted as the coolant flows through the pipework
within the freezer.
Saving energy when using your freezer
Installing:
oInstall the appliance in a cool position. If it is placed in direct
sunlight or next to an oven or other heat source, the energy
consumption can increase substantially.
oEnsure the appliance is installed with the correct ventilation
requirements. Restricting ventilation can increase the energy
consumption by 15%.
Cleaning and Maintenance:
oOccasionally clean the condenser coils (if present) at the back of
the appliance to maintain a high performance level.
oClean the door gasket with warm water or a neutral detergent
that leaves no residue. A tight-sealing door gasket is critical to
the efficiency of your appliance.
Usage:
oDo not open the door repeatedly or more frequently than you
have to.
oDo not set the thermostat too low. A change of just one degree
can effect the energy consumption by 5%. Use a thermometer to
check the temperature.
oThe freezer compartment should operate at -15 to -18 degrees
Celsius.
oAllow food to sufficiently cool before putting it in the appliance
(but don’t let it sit at room temperature for too long).
oIn the freezer, food packages should be scattered and never
grouped or stacked together until they are completely frozen.
oIf you are going away for a long period of time, turn off the
appliance, empty and clean it and leave the door ajar.

oIf you have a second appliance that is not used, make sure that
it is stored with the power off and the door left ajar until it is
actually required.
Disposing:
oIf you're going to throw out your old freezer, see if there's a
chlorofluorocarbons (CFCs) recycler in your area. The
government department which looks after the environment in
your area may be able to help you.
Cleaning and maintenance
WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO CLEAN IT.
14
oDo not clean the appliance by pouring water onto
it or spraying water over it.
oThe freezer should be cleaned periodically, using a
solution of bicarbonate of soda and lukewarm water.
oClean the accessories separately with soap and water.
Do not clean them in a dishwasher.
oDo not use abrasive products, detergents or soaps.
oAfter washing the appliance, wipe over the area that you have
cleaned with a damp cloth and then dry it thoroughly.
oWhen cleaning is complete, dry your hands and then reconnect
the plug to your mains supply.

Defrosting the freezer
Every so often you could get ice building in the freezer section. If this
occurs, then you should follow the steps below.
oWhilst defrosting the appliance, the food should be removed
from the compartment and wrapped in several layers of paper
and stored in a cool place. The foods rise in temperature will
shorten its storage life and therefore the food should be used
within a relatively short period of time.
oDO NOT PLACE FOOD BACK IN THE FREEZER
COMPARTMENT THAT HAS STARTED TO THAW.
oTurn the appliance off by turning off the power supply to the
freezer.
oRemove the drawers from the freezer and leave the door open.
You can place a bowl of warm water inside the freezer to speed
up the defrost process.
oYou can use a sponge to mop up the defrost water that will run
into the bottom of the freezer.
oIMPORTANT: You should place some old towels on the flooring
that is immediately in front of the appliance. In case any defrost
water comes out of the freezer and onto the floor.
oOnce all the ice that has built up has melted, then the inside of
the freezer should be dried thoroughly. Failure to do this will
result in immediate ice build up when the appliance is turned
back on.
oWith dry hands, reconnect your appliance to your mains supply.
You should select thermostat position MAX for a 24 hour period,
before returning it to the temperature setting of NORMAL.
oYou should not attempt to freeze fresh food inside the freezer
compartment until this 24 hour time period has elapsed.
oDo not defrost the appliance with other electrical devices
(e.g. hair dryer). Do not use sharp metal objects to
remove the ice on the freezer, as this could cause damage
to the refrigerant system.
15

16
nstallationI
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
ary for normal use and the regular operation of the
IS INTENDED FOR FITTED AND PERMANENT
.
nd who will comply with the I.E.E. and local regulations.
, then a 13 amp
ored as follows:
l
ifying the terminals
e connected to the terminal marked “L”
ected to the terminal marked “N”
arth), or by the earth symbol, or coloured green
and yellow.
plate can be found behind the freezer drawers.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necess
electric system.
Electrical connection
YOUR FREEZER
INSTALLATION.
We recommend that the appliance is connected by a
qualified electrician, who is a member of the N.I.C.E.I.C
a
oYour freezer comes supplied with a 13 amp plug fitted. If in
future you need to change the fuse in this plug
ASTA approved (BS 1362) fuse must be used.
The wiring in the mains lead is colou
Brown Live
Blue Neutra
Green and yellow Earth
oAs the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings ident
in your spur box, please proceed as follows:
The brown wire must b
(live), or coloured red.
The blue wire must be conn
(neutral), or coloured black.
The green and yellow wire must be connected to the terminal
marked “E” (e

oWhen the connection is completed, no stray strands or cut wire
should be present. The cord clamp must be secured over the
outer sheath.
Reversing the door swing
The freezer is supplied with the door hinges on the right. You can
choose whether you want the doors of your appliance to open from the
left or the right according to your kitchen design or personal
preference. If you wish to have the door hinges on the left, please
follow the instructions below.
oIt is important that this procedure is carried out before the
freezer is positioned in the desired location. The appliance
should not be connected to the mains supply.
oThe door reversal process should only be carried out by a
suitably qualified person. It is recommended that 2 people
handle the freezer during assembly. All parts that are removed
should be saved for reinstallation.
oThe freezer should be rested on something solid so that it will
not slip during the door reversal process. Do not lay the
freezer flat as this may damage the coolant system.
BEFORE: AFTER:
17

18
oUnscrew the two screws (8) that hold the bottom right hand
hinge (5) to the frame. Take away the bottom hinge (5).
oLift the door off the right upper hinge (2) and place it on a
cushioned surface to prevent scratching it.
oUnscrew the two screws (4) holding the front top panel (1) in
position. Pull gently to remove the front top panel.
oUnscrew the screw nut of the right upper hinge bin (3). Refit the
upper right hinge bin (3) into the left upper hinge (10).
oUnscrew the left front leg (9) and transfer it to the right side.
oSet the door in place, making sure the door is seated at the left
upper hinge bin (10).
oBefore replacing the bottom hinge (5), remove the bolt-pin (6)
and reverse the direction of the bottom hinge (5).
oInsert the bolt-pin (6) into the bottom hinge (5).
oWhile holding the door in the closed position, attach the bottom
hinge (5) onto the left side of the bottom frame with two screws
(8). Do not tighten the two screws (8) until the top of the door
is parallel to the counter top.
Positioning
oIt is advisable that your appliance is only installed in a location
where the ambient temperature of the room, corresponds with
the climate classification that is stated on the rating plate of your
appliance. Your appliance may not function correctly if the
ambient temperature falls outside of the following ranges.
Climate classification
Appropriate ambient temperature
SN +10 to +32 degrees centigrade
N +16 to +32 degrees centigrade
ST +18 to +38 degrees centigrade
T +18 to +43 degrees centigrade
oPositioning the appliance requires two people in order to avoid
injuries or damage to the appliance.
oKeep a minimum of 50 mm between your freezer and the back
wall. There should also be a gap of 25 mm either side and 50
mm clear space above the freezer. If there is insufficient space
this can create the sound of vibration, weakening of the
appliance’s power and a waste of electricity.

oThe appliance should never be placed upside down or carried in a
horizontal position.
oYour appliance should not be located in direct sunlight or
exposed to continuous heat or extremes of temperature (e.g.
next to a radiator or boiler). If this is not possible, then you
should install an insulation plate between the appliance and the
adjacent heat source.
oYou should check whether there is an electrical socket available,
which will be accessible after your appliance is installed.
oPlace the appliance flatly and firmly on a solid base. The
appliance is fitted with adjustable feet on the front side, which
can be used to level the appliance.
oIf the front of the appliance is positioned slightly higher than the
rear, the door can be opened and closed more easily.
19
oIf your freezer tilts down to the left, turn the
left adjusting leg until the appliance is level.
oIf your freezer tilts down to the right, turn
the right adjusting leg until the appliance is
level.
oBe sure to leave enough space for the
opening of the door, to avoid damage to the appliance or
personal injury.
Troubleshooting
IMPORTANT: If your freezer appears not to be
operating properly, before contacting the Baumatic
Customer Care Department, please refer to the
checklist below.
My freezer does not appear to be working/there is no
power to my appliance.
oCheck that the plug is fully inserted into the power socket.
oCheck that there is power to your mains supply (e.g. that there
hasn’t been a power cut or that the fuse hasn’t blown).
oCheck that the control dial has not been turned to the off setting.

oCheck that your mains supply voltage, corresponds to the
voltage stated on the rating plate of your appliance.
My freezer appears to be performing poorly.
oCheck that the appliance isn’t overloaded and that food hasn’t
been packed too tightly into it.
oThe thermostat setting is too low; you should turn the
thermostat dial to a higher setting.
oEnsure that the doors are closing properly and that the doors
have not been opened for a prolonged period in error.
oEnsure that there is adequate ventilation for your appliance and
that the ambient temperature is appropriate.
My freezer is noisy.
oThe refrigerant gas that circulates the pipework of the appliance
may make a slight noise, even if the compressor is not running.
oIf the noise worsens or the appliance gets louder than normal;
check that it is levelled off correctly, that nothing is touching the
rear of the freezer and that nothing placed inside the appliance is
rattling.
Excessive frost and ice has built up in the freezer.
oMake sure that the door is not left open for prolonged periods of
time.
oCheck there is nothing preventing the door from closing correctly
and that the door gasket is clean and intact.
oIt is normal for frost to build up over a period of time and when
this happens you should follow the “Defrosting the freezer”
instructions on page 15.
20