Bazooka BASE TUBE Guide

TOYOTA FJ CRUISER 2007- BASE TUBE (BAZOOKA
®)
Part Number: 00016-60009
Accessory Code:
Kit Contents
Item # Quantity Reqd. Description
1 1 Bazooka Tube Assembly
2 1 Wire Harness
3 1 Hardware Bag
4 1 Care Card
Hardware Bag Contents
Item # Quantity Reqd. Description
1 4 4” Wire Ties
2 4 M6 X 30mm Bolts
3 2 M6 X 25mm Bolts
4 2 Main Plate w/ mounts
5 2 L- Mounting Plates
6 4 M6 X 30mm Bolts
7 2 Washers
Additional Items Required For Installation
Item # Quantity Reqd. Description
1
Conflicts
None
Recommended Tools
Personal & Vehicle
Protection
Notes
Vehicle Protection Seat/Floor Covers
Part Protection Blankets
Special Tools Notes
Installation Tools Notes
Panel Removal Tool Nylon Removal Tool (NRT)
Socket/Ratchet 10mm
Socket Extension 6 inch
Torque Wrench 3 lbf·ft
Pliers 1. Diagonal Cutters
2. Long Nose (optional)
Screwdriver Magnetized Philips # 2
Special Chemicals
General Applicability
All Toyota FJ Grades
Recommended Sequence of Application
Item # Accessory
1 Install Security/Audio
2 Install Bazooka Tube
3 Install Door Sills
4 Install Molded Dash
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item # Quantity Reqd. Description
1
Bass Tube Specifications
Woofer Size 8”
Voice Coil Size 1”high power/high
temp.
Magnet Size 15 oz.
Frequency Response 39 – 85 hz.
Efficiency 105dB
Power Handling 100 watts
Dimensions 18.125” x 8.5” x 10”
Weight 14 lbs.
Impedance 2 ohms DVC
Southeast Toyota Distributors, LLC Page 1 of 9

TOYOTA FJ CRUISER
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-
•Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
•Safety (eye protection, rechecking torque procedure, etc.).
•Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
•Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Pre-installation Precautions
(a) Use Seat & Floor Protectors and Fender
Covers/Blankets to avoid damage to
surfaces. Operator Safety Warning (if
applicable.)
2. Battery Disconnect
(a) NOTE: Be sure to open the rear hatch,
PRIOR to disconnecting the battery.
(b) Remove the NEGATIVE (-) battery
terminal using a 10mm socket before any
disassembly starts. (Fig. 2-1).
3. Disassemble Center Rear Storage Area
(a) Remove Cargo Net Cleats using 10mm
Socket. Place in a safe location.
(b) Remove Side Trim Cover, Quarter Trim
Pocket, Quarter Trim Pocket Tray. (Fig.
3-2)
Fig 2-1
Fig 3-2
STOP
STOP
STOP
Southeast Toyota Distributors, LLC Page 2 of 9

BASS TUBE (BAZOOKA®)
4. Mount L-Brackets
(a) On wheel well, slide L-brackets under
side garnish ensuring no wires are
pinched. Insert Ground ring between
front L-bracket and vehicle. DO NOT
TIGHTEN AT THIS POINT! (Fig. 4-1)
NOTE: It may be necessary to unsnap
factory harness clip to align rear L-bracket.
5. Route Wire Harness
(a) Plug harness in at point shown. (Fig. 5-1)
(b) Route Wire harness as shown. (Fig. 5-2)
(c) Secure Wire harness at regular intervals
using 4” wire ties.
Fig. 4-1
Fig 5-1
(1) Fig. 5-2
Southeast Toyota Distributors, LLC Page 3 of 9

BASS TUBE (BAZOOKA®)
6. Install Main Plate
(a) Using the Cargo Cleats and the M6 x
35mm, loosely mount the top of the main
plate. DO NOT TIGHTEN AT THIS
POINT! See Fig 6-1.
(b) Route wiring harness through slot in
Main plate as shown. (Fig 6-2)
(c) Using two M6 x 20mm bolts and a
washer, bolt the lower points of the main
plate to the L-Brackets. DO NOT
TIGHTEN AT THIS POINT! (Fig. 6-3)
7. Tighten All Bolts
(a) Tighten bottom L-bracket bolts.
(b) Tighten Cargo cleat bolts.
(c) Tighten Main Plate bolts to L-brackets.
Fig 6-1
Fig 6-2
Fig 6-3
Southeast Toyota Distributors, LLC Page 4 of 9

BASS TUBE (BAZOOKA®)
8. Install Bass Tube
(a) Hang Bass Tube on Main Mounting
Plate as shown
(b) Using two M6 x 20MM bolts, tighten
down upper bolts as indicated in Fig 8-4.
(c) Plug Harness Connector into Bass Tube.
Fig 8-4
Southeast Toyota Distributors, LLC Page 5 of 9

TOYOTA FJ CRUISER 2007 - BASS TUBE (BAZOOKA®)
Checklist - these points MUST be checked to ensure a quality installation.
Check: Look For:
Accessory Function Checks
Turn on Radio
Verify CD & Satellite Tuner (if equipped)
Antenna is functioning
Bazooka Tube operation
Vehicle Function Checks
Hazard Button
HVAC
Rear Window Defogger
Passenger Seat Belt Warning Light
Radio display turns on & sound is heard
CD player functions & Satellite Tuner
stations are playing (if equipped)
Reception of AM/FM stations
Bazooka Tube – Listen to Bazooka Tube to
make sure it is functioning properly or by
feeling the Bazooka for vibration. Be sure
the Phase Switch is in the “UP” position.
Functioning Hazard Lights
All HVAC controls function properly
Functioning Rear Window Defogger
Functioning Seat Belt Warning Light
Southeast Toyota Distributors, LLC Page 6 of 9

TOYOTA 2007 - BASS TUBE (BAZOOKA®)
Troubleshooting
Troubleshooting
Condition: Check For:
No sound from Bass Tube, however factory
speakers still play
Distorted Sound
Low Sound
Rattling Noises
1. Is the green L.E.D. lit on the Bass Tube?
If not, check for 12 volts on pins of the Bass
Tube Connector with the ignition on. If
either pin doesn’t indicate 12 volts, check T-
Harness connectors behind the radio.
2. Is the 14-pin Molex connector securely
connected to the Bass Tube?
3. Is the ground ring securely fastened to the
rear center Anchorage bolt?
1. Close the back hatch of the vehicle
2. Adjust the radio to a comfortable listening
level, and then turn the “gain control” knob
on the Bass Tube counter-clockwise until the
sound becomes clean.
1. Close the back hatch of the vehicle
2. Adjust the radio to a comfortable listening
level, and then turn the “gain control” knob
on the Bass Tube clockwise until the sound
becomes audible. Do not adjust the level too
high, as this will result in distorted sound.
Rattling will be evident in some panels at
extreme volume conditions, but make sure
you have performed the following to
minimize noise:
1. Securely tightened Mounting Hardware so
Bass Tube Bracket does not move.
Southeast Toyota Distributors, LLC Page 7 of 9

TOYOTA 2007 - BASS TUBE (BAZOOKA®)
Troubleshooting
Troubleshooting
Condition: Check For:
Dimming Radio Lights
Radio does not come on
No Sound at all
Bass Tube produces sound on the right or
the left, but not both.
Dimming Radio Lights could occur when the
Bass Tube is played at high volumes.
Check to ensure that the main connector,
antenna connector, and auxiliary connector
have been correctly plugged back in.
1. Is the fuse under the hood still
operational?
2. Is the battery ground reconnected?
3. Is the radio connector securely seated?
Check T-Harness connections at the back of
the radio. All connectors must be securely
fastened to the correct wiring for both
channels to produce audio output.
Southeast Toyota Distributors, LLC Page 8 of 9

TOYOTA FJ CRUISER 2007- BASS TUBE (BAZOOKA®)
Wire Harness & Radio Wiring Schematics
Wire Harness & Radio Wiring Schematics
WIRING CONNECTOR SCHEMATICS:
Harness Split Radio Connector Subwoofer Connector
Harness Split Connector
Pin No. Wire Color Function
1 Red 12 Volt Battery Connection (B+)
2 White/Black Left Front Speaker (-)
3 Gray/Black Right Front Speaker (-)
4 Blue/White Remote Turn-On/Ignition (Switched+)
5 White Left Front Speaker (+)
6 Gray Right Front Speaker (+)
Subwoofer Connector
Pin No. Wire Color Function
1 Black Chassis Ground
2 N/A N/A
3 N/A N/A
4 N/A N/A
5 White Left Front Speaker (+)
6 Grey Right Front Speaker (+)
7 N/A N/A
8 Red 12 Volt Battery Connection (B+)
9 Blue/White Remote Turn-On/Ignition (Switched+)
10 N/A N/A
11 N/A N/A
12 White/Black Left Front Speaker (-)
13 Grey/Black Right Front Speaker (-)
14 N/A N/A
Radio Connector (R4 GRAY)
Pin No. Wire Color Function
1 Right Front Speaker (+)
2 Left Front Speaker (+)
3 NO CONNECTION NO CONNECTION
4 NO CONNECTION NO CONNECTION
5 12 Volt Ignition Switched (B+)
6 12 Volt Battery Connection (B+)
7 Right Front Speaker (-)
8 Left Front Speaker (-)
9 Chassis Ground (B-)
10 Power Antenna Control (+)
11 Power Antenna Control (-)
12 Dimmer / Illumination Control (B+ variable)
Southeast Toyota Distributors, LLC Page 9 of 9