Beacon FP0121-P User guide

1
INSTALLER: Leave this manual with the
appliance.
CONSUMER: Retain this manual for future
reference.
When Fire Pit is not in use — disconnect
Propane Tank.
If Fire Pit is stored indoors — remove
Propane Tank.
This Fire Pit must be attended at all times!
Do not store or use gasoline or other
ammable vapors or liquids in the
vicinityof this or any other appliance.
An LP-cylinder not connectedfor use
shall not be stored in the vicinity of this or
any other appliance.
For use with tanks marked PROPANE only.
DO NOT connect to a remote gas supply.
Propane Tanks sold separately.
Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
If the information in this manual is not
followed exactly, a fire or explosion
may result causing property damage,
personal injury, or loss of life.
Shut off gas to the appliance.
Extinguish any open ame.
If odor continues, leave the area
immediately.
After leaving the area, call your gas
supplieror fire department.
Failure to follow these instructions could
result in fire or explosion, which could
cause property damage, personal injury,
or death.
FIRE OR EXPLOSION HAZARD
If you smell gas:
Design certified under ANSI Z21.97-2017/CSA2.41-2017 Standard Outdoor Decorative Gas Appliances.
WINE BARREL
GAS FIRE PIT
MODEL#: FP0121-P
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as camper, tent,
car or home.
DANGER

WARNING Read and follow all instructions and warnings in this Owner’s Manual thoroughly
before installing, operating, or servicing this Fire Pit.
Improper installation, use, maintenance, adjustment or storage can cause fire or
explosion, resulting in serious injury or property damage.
prepare for use:
Keep away from Combustible/Flammable Items
• Combustible materials should never be within 1.83 m/6 ft of the top, 1.22 m/4 ft of back or sides of Fire Pit.
Inspect for leaks, wear and damage
• Open door and check for gas leaks before use - See page 7, Step #9 for instructions on how to check for gas leaks.
• Inspect burner and hose before use - Replace if there is evidence of excessive abrasion, wear, or damage.
• Inspect hose before each use. Hose assembly must be replaced prior to use if there is evidence of excessive abrasion or wear or if
hose is damaged. Use a manufacturer-specified replacement hose only.
Prepare area, ensure proper use of Fire Pit Cover
• Make sure ventilation openings on sides of Fire Pit (BODY) are open and clear of debris.
• Do not lay Nylon Fire Pit Cover over Fire Pit for at least 4 hours after it is turned OFF and has completely cooled down.
and to replace any part of the control system and any gas control that has been under water.
• Remove Nylon Fire Pit Cover from Fire Pit before operating.
when in use:
Do’s
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• Keep fuel supply hose away from any heated surfaces.
Don’t’s
• Do not use Fire Pit for cooking.
• Do not burn any other materials other than what is supplied with and intended for use in Fire Pit.
• Solid fuels shall not be burned in this Fire Pit.
• Do not pour water into Fire Pit.
• Do not move Fire Pit while in operation.
• Fire Pit should never be operated by children. Children must be supervised when they are anywhere near Fire Pit.
• Do not rest feet on Fire Pit.
when not in use:
• The cylinder must be disconnected when the Fire Pit is not in use.
• Remove battery from ignitor when not using Fire Pit for an extended length of time.
• Clean battery contacts and also those on the device prior to battery installation.

3
DANGERS AND WARNINGS
THIS PRODUCT USES PROPANE ONLY
when storing Fire Pit:
Storage of Fire Pit indoors is permissible only if the cylinder is disconnected and removed from Fire Pit. Cylinders must be stored outdoors in a
well-ventilated area out of reach of children. Disconnected cylinders must have threaded valve plugs tightly installed and should not be stored in a
building, garage or any other enclosed area.
Turn OFF control knob and close propane cylinder valve. Turn coupling nut counterclockwise by hand only—do not use tools to disconnect. Loosen
cylinder screw beneath bottom shelf, then lift propane cylinder up and out of stand. Place dust cap on cylinder valve outlet whenever the cylinder is
not in use.
WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner's information
manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.
The Propane-gas supply cylinder must be disconnected when this appliance is not in use.
Repairs should be done by a qualif ied service person. Fire Pit should be inspected before use and at least annually by a qualified service person.
More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the
appliance are kept clean.
Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• Max gas supply 28cm/11 in w.c. (2.74kpa)
• Only cylinder marked "propane” may be used.
• lf you see, smell or hear the hiss of escaping gas from the propane cylinder:
2. Do not attempt to correct the problem yourself.
• A dented or rusty propane cylinder may be hazardous and should be cleared by your gas supplier prior to use.
• The gas pressure regulator provided with Fire Pit must be used.
• Do not use a propane cylinder with a damaged valve and any other worn out parts.
• Transport and store empty propane cylinders carefully and properly.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid
burns or clothes catching fire.
• Young children should be carefully supervised when they are in the area of Fire Pit.
or near Fire Pit.
Observe flame color and flame height after the Fire Pit is ignited:
1) Flame color should be yellow.
2) Flame height burns at 2 - 10 inches high.
}
2 inches to
10 inches.
Propane-gas supply cylinder to be used must be:
• Constructed and marked in accordance with the U.S. Department of
Transportation (DOT) Specifications for LP-Gas Cylinders, or the Standard
for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and
Commission, CAN/CSA-B339, as applicable;
• Provided with a listed overf illing prevention device; and
• Provided with a cylinder connection device compatible with the
connection for the appliance.
i

4
PREPARATION FOR ASSEMBLY
PACKAGE CONTENTS AND COMPONENTS
Before beginning assembly of Fire Pit, make sure all parts are present. Compare parts with package contents list. If any part is missing or
damaged, do not attempt to assemble Fire Pit.
Estimated Assembly Time: 25 minutes
NOTE: You must follow all steps to properly assemble Fire Pit. Make sure the gas valve is turned OFF before assembling.
Do not attempt to assemble without proper tools.
Maximum amount of Lava Rock to be used is 5kg (11.023 lbs).
Maximum amount of Fire Glass to be used is 10 kg (22.046 lbs).
PART DESCRIPTION QTY
A Fire Bowl 1
B Body 1
C Door 1
D Burner Ring (preassembled) 1
E Gas Screen (preassembled) 1
F Fire Glass 2 boxes
G Nylon Cover 1
H Battery 1
I Adjustable Feet 4
J Control Knob (preassembled) 1
K 1
M 1
Electric Igniter (preassembled)
Burning Components
(preassembled)
N Door Knob (preassembled) 1
C
Failure to position the parts in accordance with
these diagrams or failure to use only with parts
specifically approved with this appliancemay
result in property damage or personal injury.

5
ASSEMBLY INSTRUCTIONS
Make sure the gas supply
system is turned to “OFF”.
1
2
Turn knob (N), remove door (C)
which must remain removed when burner is
in operation.
WARNING
This fire pit requires air flow under
the unit. Do not place on uneven
surface or on grass, turf or carpet.
Questions? Please call us at
[phone] for assistance.
3Place propane tank (not included) in the metal stand inside
Body (B) and make sure the gas tank sits on the metal stand
completely. Turn the wing screw on the outer part of metal
stand clockwise to secure the gas tank tightly.
1
2
3

5
K
H
6
K
H
4a
4b
6
6
ASSEMBLY INSTRUCTIONS
4 a) Turn cylinder valve on the top
gas supply. See Figure 4a
b) Screw regulator coupling
clockwise by hand only. Make sure it
is fastened. See Figure 4b
5
Replace door (C) onto body (B) and turn knob (N) to secure.
To install battery (H), unscrew rubber cap of electric igniter (K) and place battery (H) into the battery case.
Make sure the positive pole ("+") faces out towards cap. Screw cap back to battery case tightly.
(included)
H
Hardware Used
AAA Battery x 1
Cylinder
Valve
Regulator
Coupling

7
9
ASSEMBLY INSTRUCTIONS
Before using Fire Pit, check for gas leaks.
Perform leak test in a well-ventilated area outside and where no source of spark can occur.
a) After opening door for access, open tank valve fully (counter-clockwise).
b) Turn control knob to the OFF position.
c) Apply soapy water solution (3 drops dish detergent plus 4 oz. water) to check all connections for leaks before attempting to light Fire Pit.
See Figure 9
e) Turn control knob to the ON position. If there are any leaks, soapy water
will bubble where leak is occurring.
WARNING
Keep lava rock/ re glass and
other objects off of screen (shown
at left).
Holes in the screen must be
exposed in order to allow gas to
escape.
Blocked screen can cause gas to build
inside Fire Pit and ultimately cause an
explosion and risk of serious injury.
Screen
Burner
Ring
CORRECT
Burner ring is completely
covered (except for screen).
INCORRECT
Note that the burner ring
is visible.
7a
7c
7c
Screen
7a 7b
8c
7a) Place lava rock/fire glass evenly in f ire bowl (A). Use caution when handling f ire glass as it is sharp. See Figure
7a
b) Do not place any lava rock/f ire glass over the screen. See figure 7b
c) Completely cover the entire burner ring with lava rock/fire glass. See figure 7c
Failure to completely cover the burner ring with the lava rock/f ire glass will cause flame to extinguish
occasionally.
1234
5
9

88
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
• Store the Fire Pit in a cool dry place away from direct sunlight.
• The propane tank must be disconnected and removed from the Fire Pit before the Fire Pit can be stored indoors.
• Use manufacturer-approved or -supplied replacement parts and accessories only. Use of unauthorized replacement parts may void the warranty.
• Keep Fire Pit free and clear from combustible materials.
•Visually inspect burner ring for blockages (spider webs, dirt, etc.). Keep Fire Pit free and clear from debris.
To Extinguish See figure 11
1. Push and turn control knob clockwise to "OFF" position.
2. Turn cylinder valve on gas tank to close gas supply if not in use for a long time.
WARNING! Do not place lid or nylon fire pit cover on top of Fire Pit for at least 4 hours
after use and until Fire Pit has cooled.
WARRANTY
The manufacturer's warranty will be voided by, and manufacturer disclaims any responsibility for,
the following actions:
• Use of any component part not manufactured or approved by manufacturer.
• Use and installation other than as instructed in this manual.
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
WARRANTY
Before each use, open the door to inspect hose. Replace hose if there are any signs of cutting, wear or abrasion.
WARNING!
and cause injury to the face or eyes.
Caution: Only use pressure regulator and hose assembly supplied with Fire Pit. Replacement
pressure regulator and hose assemblies must be specified or supplied by manufacturer.
To Light
1. Turn cylinder valve on top of propane tank counterclockwise to open gas supply.
2. Close door on body of Fire Pit.
3. To ignite burner ring: See figure 10
a) press and hold electric igniter button (a), and
b) at the same time, push in and turn control knob (b) counterclockwise, to LOW position.
c) Keep the control knob (b) pushed in to light the burner ring.
WARNING! If ignition does NOT immediately occur
• release electric igniter button (a) and turn control knob to OFF (clockwise).
• WAIT 5 MINUTES to clear out the gas!
• repeat lighting instrutions in Step 3, above
4. After ignition, release electric igniter button (a).
Continue to push and hold the control knob for 45 seconds.
Note: Flame should be yellow/blue color.
i i
i
i i
a
b
10
a
b
11

9
No Igniter battery or igniter battery low on
power Replace with new igniter battery.
Igniter battery is incorrectly inserted Reinsert the battery properly.
Igniter broken or cracked Call customer service for replacement part.
Ignition wire is loose or disconnected to
igniterReinsert ignition wire.
Electricity leakage in ignition wire or the
needle of ignition wire not aimed at the
burner hole while lighting
Call customer service for replacement part.
Gas cylinder valve not
openGas cylinder valve not open Open gas cylinder valve.
Inproperly connect between
regulator and gas cylinder
No gas in cylinder No gas in cylinder
Regulator is loose or disconnected to gas
cylinder Check and reconnect the regulator to gas cylinder.
Check whether gas cylinder is empty; if so, replace it.
Gas cylinder valve is opened; when there is
safety valve activated
Turn the control knob to "OFF.” Close the valve
of gas cylinder and disconnect the regulator from the
gas cylinder valve. Turn the control knob to
"LOW.” Wait 30 seconds. Turn the control to
"OFF.” Reconnect the regulator to the gas
cylinder valve. Light the appliance as indicated
in the “To Light"section of manual.
Obvious gas leakage in gas system activatesCheck the gas system to see if gas leakage. If yes,
call customer service for help.
Bends or kinks in regulator hoseBend or kinks in regulator hose causeStraighten hose of all bends or kinks.
Little or no gas See"Little or no gas" above See"Little or no gas" above.
High or gusting winds Flame extinguished by high or gusting
winds
Move the appliance to the place without high or
gusting winds.
Loose connection of
thermocouple
Loose connection between thermocouple
and valveCall customer service for help.
Debris falls into inside guard and blocks
Inside guard blocked by debris
the entrance of oxygen
Debris falls into inside guard and blocks the
low temperature while igniting
Guard covered by debrisGuard covered by debris causes
improper burning inside hole of guard
Remove the debris from the guard as indicated in
manual.
Too much carbon deposited
inside guard
The carbon deposits will occur if the
the appliance
Open the top of guard by using pincer and clean the
carbon deposits in guard, hermocouple, ignition
wire, and burner. Replace the top of guard .
been activated
Little or no
gas
No spark
between
ignition wire
and burner
hole while
pushing the
igniter button.
Flame goes
out
No power in igniter
The ignition wire isn't conducting
electricity
other components.
Toll free number: 1-844-613-9170 (English); Monday to Friday from 9:00 AM to 5:00 PM (Eastern time)
i