Kingsman Fireplaces FP2085 Manual

FPB30SGT / FPB30TBT / FPB32SGT / FPB32TBT
Fire Bowl Setup
Requires Kingsman FP2085 Round Fire Pit
Kingsman Fireplaces 2340 Logan Ave., Winnipeg, Mb Canada Ph: 204-632-1962 Printed in Canada P/N 30FBT-MAN17 December 3, 2021

2

FPB30SGT / FPB30TBT / FPB32SGT / FPB32TBT Fire Bowl Warranty
All Fire Bowl (Bola) products are warranted against manufacturing defects for one year. Should your Kingsman product
experience damage due to a manufacturing defect, Kingsman will replace the damaged product free of charge (proof of
purchase is required). Installation, labor, and freight are not included.
This warranty does not include splitting, chipping, cracking or other damage that may be caused by impact, abrasion,
overloading or improper installation.
TABLE OF CONTENTS
Fire Bowl Warranty......................................................................................................................
3
Table Of Contents.......................................................................................................................
3
Warnings......................................................................................................................................
3
Fire Bowl Setup............................................................................................................................
4-6
Kingsman Outdoor Fire Pit Media Section...................................................................................
7-8
Fire Bowl Accessories…………………………………………………………………………………..
9
WARNINGS
• Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised
when they are in the area of the appliance.
• Clothing or other flammable materials should not
be hung from the appliance, or placed on or near
the appliance.
• Any guard or other protective device removed for
servicing the appliance must be replaced prior to
operating the appliance.
• Installation and repair should be done by a
qualified service person. The appliance should be
inspected before use and at least annually by a
qualified service person. More frequent cleaning
may be required as necessary. It is imperative the
control compartment, burners and circulating air
passageways of the appliance be kept clean.
• Inspect the fuel supply connection (including the
hose for LP Propane models) before each use of the
appliance.
• If it is evident there is excessive abrasion or wear,
or the hose is cut, it must be replaced prior to the
appliance being put into operation.
• Cylinders must be stored outdoors in a well-
ventilated area out of the reach of children.
Disconnected cylinders must have threaded valve
plugs tightly installed and must not be stored in a
building, garage or any other enclosed area.
• Storage of this appliance indoors is permissible
only if it has been disconnected from its fuel supply
(Natural gas line or LP Propane gas cylinder).
LP PROPANE GAS WARNINGS
• The LP Propane gas supply cylinder used with LP
models must be constructed and marked in
accordance with the specifications for LP Propane
gas cylinders of the U.S. Department of
Transportation (DOT).
• The pressure regulator and hose assembly supplied
with LP Propane models must be used. Replacement
pressure regulators and hose assemblies must be
those specified in this manual.
• The LP Propane gas cylinder supply system must
be arranged for vapor withdraws.
• The LP Propane gas cylinder used must include a
collar to protect the cylinder valve.
• When an LP Propane model is not in use, the LP
Propane gas must be turned off at the supply
cylinder.
• Fuel Supply line must not come into contact with
surfaces having temperatures in excess of 140°F. LP
gas cylinder must be kept a minimum of 4.5 feet from
the appliance.
• You must use an approved LP Propane cylinder
retention device.
⚠WARNING:
DO NOT LEAVE FIRE PIT UNATTENDED
WHEN IN USE
⚠ WARNING:
Failure to position the parts in accordance with
these diagrams or failure to use only parts
specifically approved with this appliance may
result in property damage or personal injury.
3

FPB30TBT / FPB30SGT / FPG32SGT / FPB32TBT Fire Bowl Setup
THE INSTALLATION OF THIS KIT MUST ONLY BE UNDERTAKEN BY A QUALIFIED AND CERTIFIED
GAS APPLIANCE INSTALLER.
PARTS LIST:
• Fire Bowl
• Mounting Plate with Backplate
• [1] Bag MLR1410 – ¼” Lava Rock
(20LBS)
• Leg Extension Set (3 Leg Pieces, 3
Cross Braces)
• Filler Strip Ring (3 Pieces - Assembled)
• Bag of Hardware
(3 Machine Screws & Nuts, 3 DT Screws)
1. Invert Fire Pit and attach Leg
Extensions to Fire Pit with [3] DT Screws.
Attach [3] cross braces to Leg Extensions
with hardware provided.
1/4” - 3/8” GAP
NOTE: Support sides of Fire Pit when
inverted so that Igniter Electrode does
not become damaged. Gap must be
maintained at 1/4” - 3/8”.
Upper Mount is
for 32” Bowl
Lower Mount is
for 30” Bowl
NOTE: The Leg Extensions have 2 mount positions for the FP2085 Fire Pit:
FPB30TBT / FPB30SGT
30” Bowl
FPB32TBT / FPB32SGT
32” Bowl
4

2. Disconnect
LP Propane
Hose from Valve
Assembly if
connected.
Remove Valve
and Push Button
Igniter from
Instrument
Panel. Route
Valve and Push
Button Igniter
lines to the right
of the original
location on
the Fire Pit.
Disconnect
LP Hose
Valve
Push Button Igniter
3. Insert gas supply line into Fire Bowl through one of
the bottom holes. Place Fire Pit into Fire Bowl. Connect
Gas Supply to Valve.
Gas Supply
Route Lines Here
4. Insert Push
Button Igniter
through Backplate.
Place Mounting
Plate into opening
in Fire Bowl.
Secure Igniter with
retaining nut. Next
insert Valve
through Backplate
and secure with
retaining nut.
Tighten
thumbscrews on
Backplate.
Mounting Plate
Backplate
Thumbscrew
Thumbscrew
Push Button Igniter
Valve
Route Lines Here
Push Button Igniter
Valve
NOTE: Push Button
Igniter wires must
have 1” clearance
from Brass Fittings
5. Install battery and cap onto Push Button Igniter.
Install knob onto valve.
Original Location
Original Location
5

6. Assemble Filler Strip Ring
and place onto Fire Pit.
7. Refer to Kingsman Outdoor Fire Pit Media Section for media options.
6

Kingsman Outdoor Fire Pit Media Section
REQUIRED AMOUNT OF MEDIA
ACCESSORY ITEM
FP2785 Rectangular
Fire Pit
FP2085 Round Fire
Pit Only
FP2085 Round Fire
Pit With Fire Bowl
ROCKS
*MLR1410 - 1/4" Lava
Rock 10 LBS
10 LBS
(1 BAG)
10 LBS
(1 BAG)
20 LBS
*(2 BAGS)
*Fire Bowl Includes: ¼” Lava Rock – 10LBS
-MQ DEALERS ONLY-
MQSTONE -
Decorative Stones 1 BAG 1 BAG 2 BAGS
NOTE: The MQSTONE requires a Glass or Lava Rock Base.
GLASS
MQG5W -1/2” White
Glass 5LBS
20LBS
(4 BAGS)
20LBS
(4 BAGS) 30-35LBS
(6-7 BAGS)
MQG5C - 1/2”Bronze
Glass 5LBS
20LBS
(4 BAGS) 20LBS
(4 BAGS) 30-35LBS (6-7 BAGS)
MQG5A - 1/2”Cobalt
Blue Glass 5LBS
20LBS
(4 BAGS) 20LBS
(4 BAGS) 30-35LBS (6-7 BAGS)
MQG5B -1/2” Black
Glass 5LBS
20LBS
(4 BAGS) 20LBS
(4 BAGS) 30-35LBS (6-7 BAGS)
MQG10C - 1/4"
Reflective Bronze
Glass 10 LBS
20LBS
(2 BAGS) 20LBS
(2 BAGS) 30-35LBS (3-4 BAGS)
MQG10B - 1/4" Black
Glass 10 LBS
20LBS
(2 BAGS) 20LBS (2 BAGS) 30-35LBS (3-4 BAGS)
Media Examples Shown Below.
FP2085 Without Media
¼” Lava Rock (1 Bag – 10LBS)
MEDIA REQUIREMENTS OPTIONS: (When not using LOGC85 Log Set)
20 LBS of Glass Required for Fire Pits, if using the Fire Bowl add an additional 10-15LBS of Glass.
One bag of MQSTONE may be used for the Fire Pit, if using the Fire Bowl an additional bag may be used.
One [10LB] bag of 1/4" Lava Rock is required for the Fire Pit and an additional [10LB] bag for the Fire Bowl (2-10LB bags
of 1/4” Lava Rock are supplied with Fire Bowl) may be used to fill the entire Bowl with the same material.
7

¼” Lava Rock & ¾” Lava Rock (Supplied with Fire Pit).
(1/4” Lava Rock is used as Base.)
¼” Reflective Bronze Glass - (20LBS)
MQSTONE with ¼” Lava Rock Base – (10LBS)
MQSTONE with ¼” Bronze Glass Base – (20LBS)
NOTE: MQSTONE Requires a Glass or Lava Rock Base.
8

Fire Bowl Accessories
FPB30TRG Trim Ring for FPB30TBT & FPB30SGT
FPB30COVB Cover for FPB30TBT & FPB30SGT
Caring for your Fire Pit Cover
The key to keeping your outdoor fabric looking great and extending its
life is periodic cleaning followed by repellency treatment. Mildew can
be a problem for any outdoor fabric. Mildew will not grow on a clean
synthetic fabric. Combined with humidity, the dirt and debris, which
accumulate on and in the fabric, create the ideal conditions for mildew
propagation. Thus, keeping outdoor fabric both clean and dry is
essential to eliminate or minimize mildew growth.
* Brush surfaces with soft brush to remove soil.
* Soak with warm, soapy water (not to exceed 100 degrees
Fahrenheit).
* Use a mild soap such as Ivory, or Dawn. Do not use detergents,
abrasives or cleaners.
* Rinse fabric thoroughly after cleaning.
* Let fabric air dry after rinsing
* Do not machine dry.
Treating your Fabric
* Before "retreating" or "protecting" a fabric, the fabric must be thoroughly cleaned. Fabric protector products bond most effectively to
perfectly clean fabric. Anything not removed from the fabric will interfere with the bonding and performance of the product. All dirt,
body oils, sweat, soap residue will impede bonding and performance.
* Do not over spray. Saturation is not necessary. The surface needs to be slightly damp, but not soaked. Two lighter coats are better
than one heavy coat. An even coating is more likely with two applications. Let the first coating dry to the touch before applying the
second - generally an hour.
* The quicker you can get a fabric protector product to dry, the better bonding and performance you will achieve. It is best to treat the
fabrics in warm weather, such as a hot day in full sun.
* Maintenance is essential. You can lightly mist the surface every 6 months to check the water repellency. Friction will wear away
product more quickly leaving the fabric unprotected. If this is the case, such areas can be spot treated to renew repellency.
* Just a note - Silicone water repellents are not true "fabric protectors". While they do develop good repellency, they often retain a
tackiness that attracts dirt. Silicone treated fabrics soil much more rapidly than untreated fabrics, have no resistance to oil-based
stains, and can make fabrics more difficult to clean once soiled.
Fabric Guard
Recommended as the best fabric protectant 303® High Tech Fabric Guard™ is a premium patented formula that restores fabrics lost
water and stain repellency. Yearly maintenance with 303 Products will add to the life of your fabrics.
9

10